Search results

This study aims to determine the influence of bruise damage generated from the impact test on the physical, chemical and nutritional responses of tomato fruit.

The impact loading was applied from different heights. The impact energies for 20, 40 and 60 cm drop heights were 129.59, 259.18 and 388.77 mJ, respectively. The injured samples were kept for 48 hours at low (10 °C) and ambient (22 °C) storage temperatures. Weight loss, firmness, color, total soluble solids (TSS), lycopene and carotenoids were measured before the impact test (day 0) and after 48 hours of the impact and storage.

The drop height of 60 cm and storage at 22 °C showed the highest values in the bruised area. The impact from the 60 cm drop height significantly reduced weight, lightness, yellowness, hue, firmness, lycopene and carotenoids, particularly at 22 °C storage condition. Redness (a*) and color index (CI) showed a remarkable increase (p < 0.05) at 22 °C on tomatoes affected from the highest impact level (388.77 mJ) after 48 hours of storage. No pronounced significance was seen between TSS and drop heights. This study has confirmed that tomato bruising for a short-term storage period induces physiological changes at different storage temperature conditions.

The study can confirm the crucial role of inappropriate handling in increasing fresh produce loss within short-term storage. Also, this research can be considered as a guideline for transporters, handlers, processors, distributors and horticulture researchers in the fresh produce supply chain during postharvest operations.

The South African wool industry is integral to the country's agricultural sector, particularly sheep farming and wool production. Small-scale farmers play a vital role in this industry and contribute to employment and food security in rural communities. However, these farmers face numerous challenges, including a lack of funding, poor farming practices and difficulty selling their wool at fair prices. This study aims to address these challenges, the University of Free State launched a wool value chain project for small-scale farmers.

In this project, one of the studies conducted assessed the effectiveness of different detergents suitable for traditional wool scouring methods for small-scale farmers who lack access to sophisticated machinery. The investigation was conducted by scouring 160 wool samples using three different detergents and filtered water as a control. The wool samples were then evaluated for their cleanliness, brightness and fibre properties through a combination of scanning electron microscopy, spectrophotometry and statistical analysis at different scouring times (3, 10, 15 and 20 min, respectively).

The results showed that the combination of scouring time and the type of scouring solution used could significantly impact wool quality. It was found that using a combination of standard detergent or Woolwash as a scouring solution with a scouring time of 10–15 min resulted in the best outcome in terms of fibre property, wool colour and scouring loss.

This study demonstrated that traditional wool scouring methods could be an option for small-scale farmers and anyone who want to learn how to scour wool without expensive machinery to make wool products.

This study aims to investigate the effect of the copresence of ferrous (Fe²⁺) ions and sodium dodecyl sulfate (SDS) on the activity of an amylase enzyme during the desizing of greige viscose fabric for potential industrial applications. The removal of starches is an essential step before processing the fabric for dyeing and finishing operations. The authors tend to accomplish it in eco-friendly and sustainable ways.

The experiments were designed under the Taguchi approach, and the results were analyzed using grey relational analysis to optimize the process. The textile properties of absorbency, reducing sugars, bending length, weight loss, Tegawa rating and tensile strength were assessed using the standard protocols. The control and optimized viscose specimens were investigated for certain surface chemical properties using advanced analytical techniques including scanning electron microscopy (SEM), X-ray diffraction (XRD) and thermal gravimetric analysis (TGA).

The results demonstrate that the Fe²⁺ concentration and process time were the main influencing factors in the amylolytic desizing of viscose fabric. The optimized process conditions were found to be 0.1 mm Fe²⁺ ions, 3 mm SDS, 80°C, 7 pH and 30 min process time. The copresence of Fe²⁺ ions and SDS promoted the biodesizing of viscose fabric. The SEM, Fourier transform infrared spectroscopy, XRD and TGA results demonstrated that the sizing agent has efficiently been removed from the fabric surface.

The amylase desizing of viscose fabric in the presence of certain metal ions and surfactants is a significant subject as the enzyme may face them due to their prevalence in the water systems. This could also support the biodesizing and bioscouring operations to be done in one bath, thus making the textile pretreatment process both economical and environmentally sustainable.

The authors found no report on the biodesizing of viscose fabric in the copresence of Fe²⁺ ions and the SDS surfactant under statistical multiresponse optimization. The biodesized viscose fabric has been investigated using both conventional and analytical approaches.

Gourd fibres (GF) are a natural biodegradable fibre material with excellent mechanical properties and high tensile strength. The use of natural fibres in composite materials has gained popularity in recent years due to their various advantages, including renewability, low cost, low density and biodegradability. Gourd fibre is one such natural fibre that has been identified as a potential reinforcement material for composites. However, it has low surface energy and hydrophobic nature, which makes it difficult to bond with matrix materials such as polyester. To overcome this problem, chemically adapted gourd fibre has been proposed as a solution. Chemical treatment is one of the most widely used methods to improve the properties of natural fibres. This research evaluates the feasibility and effectiveness of incorporating chemically adapted gourd fibre into polyester composites for industrial fabrication. The purpose of this study is to examine the application of chemically modified GF in the production of polyester composite engineering materials.

This work aims to evaluate the effectiveness of chemically adapted gourd fibre in improving the adhesion of gourd fibre with polyester resin in composite fabrication by varying the GF from 5 to 20 wt.%. The study involves the preparation of chemically treated gourd fibre through surface modification using sodium hydroxide (NaOH), permanganate (KMnO₄) and acetic acid (CH₃COOH) coupling agents. The mechanical properties of the modified fibre and composites were investigated. It was then characterized using scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR) to determine the changes in surface morphology and functional groups.

FTIR characterization showed that NaOH treatment caused cellulose depolymerization and caused a significant increase in the hydroxyl and carboxyl groups, showing improved surface functional groups; KMnO₄ treatment oxidized the fibre surface and caused the formation of surface oxide groups; and acetic acid treatment induced changes that primarily affected the ester and hydroxyl groups. SEM study showed that NaOH treatment changed the surface morphology of the gourd fibre, introduced voids and reduced hydrophilic tendencies. The tensile strength of the modified gourd fibres increased progressively as the concentration of the modification chemicals increased compared to the untreated fibres.

This work presents the designed composite with density, mechanical properties and microstructure, showing remarkable improvements in the engineering properties. An 181.5% improvement in tensile strength and a 56.63% increase in flexural strength were got over that of the unreinforced polyester. The findings from this work will contribute to the understanding of the potential of chemically adapted gourd fibre as a reinforcement material for composites and provide insights into the development of sustainable composite materials.

This paper aims to compare the wear behavior, surface roughness, friction coefficient and volume loss of high-velocity oxy-fuel (HVOF) sprayed WC–Co and WC–Cr₃C₂–Ni coatings on AISI 1095 steel with spraying times of 10 and 15 s.

In this study, the pin-on-disc testing technique was used to evaluate the wear characteristics at a speed of 0.24 m/s, load of 40 N and test time of 60 min under dry conditions at room temperature. The wear characteristics were examined and analyzed by scanning electron microscopy and energy dispersive X-ray spectroscopy. The surface roughness of a coated surface was measured, and microhardness measurements were performed on the cross-sectioned and polished surfaces of the coating.

Spraying time and powder material affected the hardness of HVOF coatings due to differences in the porosity of the coated layers. The average hardness of the WC–Cr₃C₂–Ni coating with a spaying time of 15 s was approximately 14% higher than that of the WC–Cr₃C₂–Ni coating with a spraying time of 10 s. Under an applied load of 40 N, the WC–Co coating with a spraying time of 15 s had the lowest variation in the friction coefficient compared with the other coatings. The WC–Co coating with a spraying time of 10 s had the lowest average and variation in volume loss compared to the other coatings. The WC–Cr₃C₂–Ni coating with a spraying time of 10 s exhibited the highest average volume loss. The wear features changed slightly with the spraying time owing to variations in the hardness and friction coefficient.

This study investigated tribological performance of WC–Co; WC-Cr₃C₂-Ni coatings with spraying times of 10 and 15 s using pin-on-disc tribometer by rotating the relatively soft pin (C45 steel) against hard coated substrate (disc).

The aim of this paper is to solve the toxic and harmful problems caused by traditional volatile corrosion inhibitor (VCI) and to analyze the effect of the layered structure on the enhancement of the volatile corrosion inhibition prevention performance of amino acids.

The carbon dots-montmorillonite (DMT) hybrid material is prepared via hydrothermal process. The effect of the DMT-modified alanine as VCI for mild steel is investigated by volatile inhibition sieve test, volatile corrosion inhibition ability test, electrochemical measurement and surface analysis technology. It demonstrates that the DMT hybrid materials can improve the ability of alanine to protect mild steel against atmospheric corrosion effectively. The presence of carbon dots enlarges the interlamellar spacing of montmorillonite and allows better dispersion of alanine. The DMT-modified alanine has higher volatilization ability and an excellent corrosion inhibition of 85.3% for mild steel.

The DMT hybrid material provides a good template for the distribution of VCI, which can effectively improve the vapor-phase antirust property of VCI.

The increased volatilization rate also means increased VCI consumption and higher costs.

Provides a new way of thinking to replace the traditional toxic and harmful VCI.

For the first time, amino acids are combined with nano laminar structures, which are used to solve the problem of difficult volatilization of amino acids.

The purpose is to provide decision support for tourists recommending scenic spots and corresponding suggestions for the management of scenic spots.

Based on the Baidu index data generated, this paper analyzes the temporal and spatial characteristics of network attention of 5A scenic spots in Sichuan Province. The online comment data are used to build the assessment model of scenic spots based on network attention, and the comment information of tourists is mined and analyzed through statistical analysis. At the same time, the key attributes of scenic spots from the perspective of network attention are evaluated and analyzed by using the probabilistic linguistic term set. Finally, this paper further constructs a recommendation model based on the key attribute set of scenic spots.

This paper uses different types of tourism network information, integrates multi-types of data and methods, fully excavates the value information of tourism network information, constructs the research framework of “scenic spot assessment + scenic spot recommendation” from the perspective of network attention, analyzes the network attention characteristics of scenic spots, evaluates the performance of scenic spots, and implements scenic spot recommendation.

This paper integrates multi-source data and multidisciplinary theoretical methods to form a scenic spot research framework of “assessment + recommendation” from the perspective of network attention.

This empirical study aims to investigate the erosion wear performance of two different 3D-printed materials (acrylonitrile butadiene styrene [ABS] and polylactic acid [PLA]) with various micro textures. The two different textures (prism and square) were created over the surfaces of both materials by using the 3D-printed technique.

The erosion experiments on both materials were performed by using Ducom Erosion Jet Tester. Erosion tests were performed at four different impacting velocities (15, 30, 45 and 60 m/s) with the four different particle sizes (17, 39, 63 97 µm) at the impact angles (30°–90°) for the time duration of 5, 10, 15 and 20 min. The two different textures prism and cone were used for performing the erosion experiments. Taguchi’s orthogonal L16 (mixed level) was used to reduce the number of experiments and to determine the impact of these parameters on erosion wear performance of both 3D-printed materials.

The PLA with cone texture was found to be best (against erosion) than the ABS cone and prism textures due to their high hardness (68 HV). Also, the average signal to noise (S/N) ratio for PLA and ABS was measured as 56.4 and 44.4 dB, respectively. As the value of the S/N ratio is inversely proportional to the erosion rate, the PLA has the least erosion rate as compared to the ABS. The sequence of erosion wear influencing parameters for both materials was in the following order: velocity > erodent size > texture > impact angle > time interval.

Both PLA and ABS with different micro textures for erosion testing were studied with Taguchi’s optimization method, and the erosion mechanisms are well analyzed by using scanning electron microscopy and Image J techniques.

This study aims to investigate the impact of regular Kung Fu and Taekwondo practice on the health and quality of life among elderly individuals in the Maule region, Chile.

The authors designed a 12-week Kung Fu and Taekwondo workshop with activities suitable for their age. Through semistructured interviews (at the beginning and the end of the workshop), along with periodic monitoring of vital signs and cardiovascular components, the authors observed an improvement in participants’ physical (strength, speed of reaction and flexibility) and psychological conditions (self-esteem and resilience), quality of life (relationships with family and friends and ability to deal with stressful events in working life) and health (waist circumference, percentage of oxygen saturation in blood, blood pressure, among other values).

From these results, the authors affirm that this workshop improves health and physical condition and helps the participants develop the coping capacity to deal with stressful situations and complicated interpersonal relationships. In this sense, the authors conclude that Kung Fu and Taekwondo as regular sports activities can benefit senior citizens’ aging process.

This research is based on an original study project.

Ireland’s ageing population has resulted in an increasing number of older adults living with frailty. Despite growing attention towards older adults’ and health professionals’ perspectives of frailty, occupational therapy research is limited. This study aims to explore occupational therapists’ perceptions of frailty and how their perceptions impact their approach to the assessment and management of frailty.

Using qualitative descriptive design, 19 occupational therapists working with older adults participated in online focus groups. Data were analysed using thematic analysis.

Perceptions of occupational therapists were constructed into three main themes: conceptualising frailty; management of frailty; and advancing frailty practice. Findings indicate that occupational therapists perceived frailty as a multidimensional concept but highlight a reluctance to use frailty terminology with patients. Findings also suggest that although occupational therapists are involved in provision of care for older adults living with frailty, the profession’s scope is not optimised in the assessment and management of frailty.

Findings provide insight into occupational therapists’ perceptions of frailty. Development of a shared understanding of frailty between clinicians and patients and enhancement of undergraduate frailty education are recommended to progress occupational therapy’s role in frailty management.