Search results

Punching can trigger catastrophic failures in flat slabs because of its sudden nature resulting from exceeding the shear capacity of slabs. Effect of using recycled aggregate, as an environmental-friendly alternative to traditional RC structures, on punching behavior of these slabs was not sufficiently investigated in the literature. Hence, this paper aims to experimentally study the effect of using recycled coarse aggregate (RCA) on the punching shear capacity (PSC) of RC flat slabs. The RCA is produced by crushing of waste of concrete standard cubes obtained from compression tests.

A total of 12 slab-column connection specimens with different slab thicknesses (140, 160 and 200 mm) and different RCA percentages (0%, 30% and 70%) were prepared and tested under a central point load, to test its effect on the behavior of flat slabs. The punching failure loads of the tested specimens were compared with those obtained according to the provisions of different international building codes.

Compared with natural aggregate concrete, mixes with 30% and 70% RCA experienced reductions in the compressive that did not exceed 4% and 21%, while reductions of 4% and 13% were observed for the tensile strength, respectively. The increase in the amount of RCA reduced the PSC by 0%–7%, 0%–4% and 4%–10% for slabs with a thickness of 140, 160 and 200 mm, respectively. For slabs with punching shear reinforcement (PSR), ACI 318 provided the closest estimation for the PSC by 9%, whereas EURO 2 overestimated the PSC by 25% and ECP 203 underestimated the PSC by 41%.

The provided conclusions are obtained from the conducted experimental work where a constant W/C ratio, aggregate type and a maximum aggregate size of 19 mm for the RCA were adopted.

Enhancement in the behavior of flat slabs with various thicknesses and amounts of RCA because of introducing PSR is experimentally evaluated. The failure loads of the tested slabs with recycled and normal coarse aggregates were compared against different code provisions.

This study aims to provide a salt ready-mix to instant fried noodles manufacturers.

Response surface methodology was used to get optimized salt ready-mix based on carbonate salt, disodium phosphate, tripotassium phospahte, sodium hexametaphosphate and sodium chloride. Peak viscosity of flour and yellowness, cooking loss and hardness of noodles were considered as response factors for finding optimized salt formulation.

The results showed that salts have an important role in governing quality of noodles. Optimum levels of five independent variables of salts, namely, carbonate salt (1:1 mixture of sodium to potassium carbonate), disodium phosphate, sodium hexametaphosphate, tripotassium phosphate and sodium chloride were 0.64%, 0.29%, 0.25%, 0.46% and 0.78% on flour weight basis, respectively.

To the best of the authors’ knowledge, this is the first study to assess the effect of different combinations of different salts on the quality of noodles. These findings will also benefit noodle manufacturers, assisting in production of superior quality noodles.

The purpose of this paper is to develop a high-performance composite emulsion cement waterproof coating. The coating has excellent durability and is effective in protecting cement mortar substrates from harmful ions.

The polymer cement waterproof coatings with different emulsion compounding ratios were tested for mechanical properties and water resistance after alkali immersion, water immersion, thermal aging and UV aging, and the coatings were analyzed by infrared spectroscopy after aging to evaluate its durability. Meanwhile, the coating that presents favorable durability was applied to cement mortar test blocks. The protective effect of the coating on the test blocks was tested by immersion method, and X-ray diffraction analysis was performed on the eroded test blocks.

The coating with neoprene latex/acrylate latex weight ratio of 90/10 presents favorable durability and has superior overall performance. Besides, when it is applied to cement mortar blocks, the coatings effectively reduced the erosive effect of harmful ions on cement mortar blocks, resulting in much lower mass change ratios and less internal structural damage of the blocks significantly.

The obtained coating will be of great application potential for use in building waterproofing construction. Moreover, the coating can practically prevent chloride ions and sulfate ions from penetrating cement-based materials.

This paper aims to study the effects of plum powder and apple pomace powder additions on the quality properties of buffalo meat emulsion.

Buffalo meat emulsions were prepared using different levels (2%, 4% and 6%) of plum powder and apple pomace powder, respectively. The meat emulsions were analysed for the physico-chemical, sensory and textural properties of the meat emulsion.

The pH of meat emulsions decreased significantly (p < 0.05) with an increased level of plum powder and apple pomace powder. Water-holding capacity (43.1%–48.1%), emulsion stability (80.2%–92.2%) and cooking yield (85.4%–91.0%) were significantly (p < 0.05) higher in plum powder and apple pomace powder added than the water-holding capacity (42.1%), emulsion stability (79.7%) and cooking yield (85.0%) of control emulsion. The moisture content was decreased significantly (p < 0.05), and crude fibre content was increased significantly (p < 0.05) with the increase in plum powder and apple pomace powder additions in meat emulsions. The total phenolic content and colour values (a* and b*) were significantly higher in plum powder and apple pomace powder added to meat emulsions. The sensory scores of meat emulsions were affected by the addition of plum powder and apple pomace powder. The meat emulsion added with 6% plum powder and 6% apple pomace powder showed significantly lower values of sensory overall acceptability. The hardness of meat emulsions increased with the addition of plum powder and apple pomace powder.

The results indicated that meat emulsions with a good cooking yield, fibre content, sensory acceptability and textural properties can be prepared by using plum powder and apple pomace powder.

Aluminum alloy is considered an ideal material in aerospace, automobile and other fields because of its lightweight, high specific strength and easy processing. However, low hardness and strength of the surface of aluminum alloys are the main factors that limit their applications. The purpose of this study is to obtain a composite coating with high hardness and lubricating properties by applying GO–PVA over MAO coating.

A pulsed bipolar power supply was used as power supply to prepare the micro-arc oxidation (MAO) coating on 6061 aluminum sample. Then a graphene oxide-polyvinyl alcohol (GO–PVA) composite coating was prepared on MAO coating for subsequent experiments. Samples were characterized by Fourier infrared spectroscopy, X-ray diffraction, Raman spectroscopy and thermogravimetric analysis. The friction test is carried out by the relative movement of the copper ball and the aluminum disk on the friction tester.

Results showed that the friction coefficient of MAO samples was reduced by 80% after treated with GO–PVA composite film.

This research has made a certain contribution to the surface hardness and tribological issues involved in the lightweight design of aluminum alloys.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2023-0427/

This paper aims to design the nano-titanium dioxide (TiO₂) coating system which has superhydrophilic property, self-cleaning mechanism and antifog property as well as strong adhesion on glass substrate.

Two hydrophilic materials have been used such as TiO₂ nanoparticles as fillers and hydrophilic copolymer, Pluronic F-127 by using simple sol–gel approach. The prepared solution was applied onto glass through dip- and spray-coating techniques and then left for drying at ambient temperature.

The nano-TiO₂ superhydrophilic coating has achieved the water contact angle of 4.9° ± 0.5°. The superhydrophilic coating showed great self-cleaning effect against concentrated syrup and methylene blue where thin layer of water washes the dirt contaminants away. The nano-TiO₂ coating exhibits great antifog performance that maintains high transparency of around 89% when the coated glass is placed above hot-fog vapor for 10 min. The fog droplets were condensed into water film which allowed the transmission of light through the glass. The strong adhesion of coated glass shows no total failure at scratch profile when impacted with scratch load of 500, 800 and 1,200 mN.

Findings will be useful in the development of self-cleaning superhydrophilic coating that is applicable on building glass and photovoltaic panel.

The developed nano-TiO₂ coating is developed by the combination of hydrophilic organic copolymer–inorganic TiO₂ network to achieve great superhydrophilic property, optimum self-cleaning ability and supreme antifog performance.

The findings will be useful for residents in building glass window where the application will reduce dust accumulation and keep the glass clean for longer period.

The synthesis of nano-TiO₂ superhydrophilic coating which can be sprayed on large glass panel and cured at ambient temperature.

The purpose of this study is to investigate the effect of the sintering temperature on the microstructural, mechanical and physical properties of Cu-SiC composites.

The powder metallurgy route was used to fabricate the samples. Cold compaction of powders was conducted at 250 MPa which was followed by sintering at 850°C–950°C at the interval of 50 °C in the open atmospheric furnace. SiC was used as a reinforcement and the volumetric fraction of the SiC was varied as 10%, 15% and 20%. The processed samples were metallurgically characterized by the scanning electron microscope (SEM). Mechanical characterization was done using tensile and Vickers’ micro-hardness testing to check the hardness and strength of the samples. Archimedes principle and Four-point collinear probe method were used to measure the density and electrical resistivity of the samples.

SEM micrograph reveals the uniform dispersion of the SiC particles in the Cu matrix element. The results revealed that the Hardness and tensile strength were improved due to the addition of SiC and were maximum for the samples sintered at 950 °C. The addition of SiC has also increased the electrical resistivity of the Cu-SiC composite and was lowest for Cu 100% while the relative density has shown the reverse trend. Further, it was found that the maximum hardness of 91.67 Hv and ultimate tensile strength of 312.93 MPa were found for Cu-20% SiC composite and the lowest electrical resistivity of 2.017 µ- Ω-cm was found for pure Cu sample sintered at 950 °C, and this temperature was concluded as the optimum sintering temperature.

The powder metallurgy route for the fabrication of the composites is a challenging task as the trapping of oxygen cannot be controlled during the compaction process as well as during the sintering process. So, a more intensive study is required to overcome these kinds of limitations.

As of the author’s best knowledge, no work has been reported on the effect of sintering temperature on the properties of the Cu-SiC composites which has huge potential in the industries.

The purpose of this paper is to study Al-based green composite. To make composite samples of aluminium alloy (AA3105) with different weight percentages of rice husk ash (RHA) and eggshell (ES) particles as reinforcement, stir casting method was used.

Several other aspects, including the weight percent of reinforcing agent particles, the applied stress and the sliding speed, were taken into consideration. During the course of the wear test, the sliding distance that was recorded varied from a minimum of 1,000 m all the way up to a maximum of 3,135 m (10, 15, 20, 25 and 30 min). The typical range for normal loads is 8–24 N, and their speed is 1.58 m/s.

With the AA/ES/RHA composite, the wear rates decreases when the grain size of the reinforcing particles enhanced. Scanning electron microscopy images of worn surfaces show that at low speeds, delaminating and ploughing are the main causes of wear. At high speeds, ploughing is major cause of wear. Composites with better wear-resistant properties can be used in wide range of tribological applications, especially in the automotive industry. It was found that hardness increases at the same time as the weight of the reinforcement increases. Tensile and hardness were maximized at 10% reinforcement mix in Al3105.

In this work, ES and RHA has been used to develop green metal matrix composite to support green revolution as promoted/suggested by United Nations thus reducing the environmental pollution.

This study aims to focus on how reactive diluents with mono- and di-functionalities affect the properties of resin formulation developed from bioderived precursors. A hydroxyethyl methacrylate (HEMA) terminated urethane acrylate oligomer was synthesized and characterized to study its application in stereolithography 3D printing with different ratios of isobornyl acrylate and hexanediol diacrylate.

Polyester polyol was synthesized from suberic acid and butanediol. Additionally, isophorone diisocyanate, polyester polyol and HEMA were used to create urethane acrylate oligomer. Fourier transform infrared spectroscopy and ¹H NMR were used to characterize the polyester polyol and oligomer. Various formulations were created by combining oligomer with reactive diluents in concentrations ranging from 0% to 30% by weight and curing with ultraviolet (UV) radiation. The cured coatings and 3D printed specimens were then evaluated for their properties.

The findings revealed an improvement in thermal stability, contact angle value, tensile strength and surface properties of the product which indicated its suitability for use as a 3D printing material.

This study discusses how oligomers that have been cured by UV radiation with mono- and difunctional reactive diluents give excellent coating characteristics and demonstrate suitability and stability for 3D printing applications.

This paper aims to assess the impact of incorporating foxnut powder (FP) into bakery products to evaluate their effect on product quality and nutritional characteristics.

Samples of refined flour (control) and refined wheat flour with varying levels of FP were prepared for each bakery item. Sensory evaluations using a nine-point hedonic scale were conducted. Different concentrations of FP (20% for cakes, 12.5% for bread and 12.5% for doughnuts) were tested to achieve sensory acceptability.

The addition of FP at specified concentrations achieved sensory acceptability in the tested bakery items, significantly impacting overall acceptability. Incorporating FP led to textural attribute alterations, including increased hardness, gumminess and chewiness, alongside reduced cohesiveness and elasticity. Color properties were influenced, affecting lightness, redness and yellowness of the bakery items. Proximate composition analysis highlighted shifts in moisture, protein, fiber, fat and ash content between control and accepted samples. Mineral content analysis revealed notable differences in calcium, potassium, iron, magnesium and sodium between control and accepted samples.

These findings demonstrate the potential of FP to enhance bakery products, offering promising industrial applications in producing nutritionally enriched and visually appealing baked products.