Search results

The purpose of this study was the preparation of a poly(styrene-co-maleic anhydride)-g-polyetheramine (SMA-g-PEA) hyperdispersant that reduces the viscosity of the system and improves the colouring intensities of pigments.

PEA of specific quality was dissolved in propylene glycol methyl ether. SMA was then added according to the required mass ratio. The solution was refluxed for 10 h under a stream of protective N2. The prepared hyperdispersant was then characterised by Fourier-transform infrared, UV–visible and ¹H NMR spectroscopies, gel-permeation chromatography and thermogravimetry.

PEA was successfully grafted onto the SMA polymer and the synthesised product was found to be thermally stable. The copolymer with a 6:1 mass ratio is the best dispersant and was used to disperse carbon black, phthalocyanine blue and permanent violet in water-based systems, which helps to improve the application performance of each pigment by reducing the viscosity of the system and improving the colouring intensity of the pigment. The water dispersion is stable and does not exhibit an increase in viscosity after seven days of oven aging at 50°C.

SMA-g-PEA water-based hyperdispersants were successfully synthesised. The prepared hyperdispersants help to improve the application performance of each studied pigment by reducing the viscosity of the system and improving the colouring intensity of the pigment.

This paper aims to study the physical and chemical characteristics of inkjet titanium dioxide inks for cotton fabric digital printing.

Different dispersing agents through the reaction of glycerol monooleate and toluene diisocyanate were prepared and then performed by using three different polyols (succinic anhydride-modified polyethylene glycol PEG 600, EO/PO Polyether Monoamine and p-chloro aniline Polyether Monoamine), to obtain three different dispersing agents for water-based titanium dioxide inkjet inks. The prepared dispersants were characterized using FTIR to monitor the reaction progress. Then the prepared dispersants were formulated in titanium dioxide inkjet inks formulation and characterized by particle size, dynamic surface tension, transmission electron microscopy, viscosity and zeta potential against commercial dispersants. Also, the study was extended to evaluate the printed polyester by using the prepared inks according to washing and crock fastness.

The obtained results showed that p-chloro aniline Polyether Monoamine (J) and succinic anhydride modified polyethylene glycol PEG 600 (H) dispersants provided optimum performance as compared to commercial standards especially, particle size distribution data while EO/PO Polyether Monoamine based on dispersant was against and then failed with the wettability and dispersion stability tests.

These ink formulations could be used for printing on cotton fabric by DTG technique of printing and can be used for other types of fabrics.

The newly prepared ink formulation for digital textile printing based on synthesized polyurethane prepolymers has the potential to be promising in this type of printing inks, to prevent clogging of nozzles on the printhead and to improve the print quality on the textile fiber.

This study aims to synthesize Prussian blue {Fe^III₄[Fe^II(CN)₆]₃} pigment by reacting ferric chloride with different ferrocyanides through the same procedure. The influence of the ferrocyanide used on resulting pigment properties is studied.

Prussian blue is commonly synthesized by direct or indirect methods, through iron salt and ferrocyanide/ferricyanide reactions. In this study, the direct, single-step process was pursued by dropwise addition of the ferrocyanide into ferric chloride (both as aqueous solutions). Two batches – (K-PB) and (Na-PB) – were prepared by using potassium ferrocyanide and sodium ferrocyanide, respectively. The development of pigment was confirmed by an identification test and characterized by spectroscopic techniques. Pigment properties were determined, and light fastness was observed for acrylic emulsion films incorporating dispersed pigment.

The two pigments differed mainly in elemental detection owing to the dissimilar ferrocyanide being used; IR spectroscopy where only (Na-PB) showed peaks indicating water molecules; and bleeding tendency where (K-PB) was water soluble whereas (Na-PB) was not. The pigment exhibited remarkable blue colour and good bleeding resistance in several solvents and showed no fading in 24 h of light exposure though oil absorption values were high.

This article is a comparative study of Prussian blue pigment properties obtained using different ferrocyanides. The dissimilarity in the extent of water solubility will influence potential applications as a colourant in paints and inks. K-PB would be advantageous in aqueous formulations to confer a blue colour without any dispersing aid but unfavourable in systems where other coats are water-based due to their bleeding tendency.

The concept of a smart city is becoming more closely linked to tourism destinations. The relationship between the environment, sustainability and tourism has become more interrelated. An eco-friendly city environment can influence tourists’ decisions, but tourist flows can also negatively impact the local ecosystem by increasing energy consumption, air pollution and environmental sustainability. In this research letter, the authors reverse this perspective, moving into smart city trajectories, highlighting that increasing tourism in cities drives the city to advance a green transition to respond to the imbalance generated by large flows of tourists that increase the users-density of the city. Thus, the purpose of this study is to investigate the symbiotic relationship between increasing tourism in cities and the imperative for a green transition.

This study builds on the generalized method of moment approach and an 11-year panel data set covering 30 Italian cities to investigate the relationship between tourism flow and the cities’ green practices embedded in the smart environment dimension.

This study provides empirical evidence that a large flow of tourists in cities positively affects the cities’ green transition, contributing to the advancement of smart tourism and smart city debate.

The study focuses only on one country, and although its results may be generalizable to the European Union, it is not representative at a global level and requires further research.

This study offers practical implications underscoring the benefits of large tourism inflow in managing and implementing smart city projects.

Tourism and overtourism may lead to a city reaction regarding green practices, which can have a multiplier benefit on the urban environment.

To the best of the authors’ knowledge, this is one of the first study attempt to investigate the tourism flow as a driver of smart city implementation, considering the city’s reaction to tourism and overtourism conditions in the city that would lead to the ecological and sustainable collapse of a city.

Current evidence indicates that humans and animals are at increased risk of multiple health challenges due to microplastic (MP) profusion. However, mitigation is constrained by inadequate scientific data, further aggravated by the lack of evidence in many African countries. This review therefore synthesized evidence on the current extent of MP pollution in Africa and the analytical techniques for reporting.

A literature search was undertaken in research databases. Medical subject headings (MeSH) terms and keywords were used in the literature search. The authors found 38 studies from 10 countries that met the inclusion criteria.

Marine organisms had MPs prevalence ranging from 19% to 100%, whereas sediments and water samples had between 77 and 100%. The most common and dominant polymers included polypropylene and polyethylene.

This review shows that most studies still use methods that are prone to human errors. Therefore, the concentration of MPs is likely underestimated, even though the authors’ prevalence evaluations show MPs are still largely pervasive across multiple environmental matrices. Also, the study reveals significant spatial disparity in MP research across the African continent, showing the need for further research in other African countries.

Even though some reviews have assessed MPs pollution in Africa, they have not evaluated sample prevalence, which is necessary to understand not only concentration but pervasiveness across the continent. Secondly, this study delves deeper into various methods of sampling, extraction and analysis of MPs, as well as limitations and relevant recommendations.

Given the distinct and unique climates in these countries, research conducted in other parts of the world may not be directly applicable. Therefore, it is crucial to conduct research tailored to the specific climatic conditions of Australia and New Zealand to ensure accuracy and relevance.

Given population growth, urban expansions and predicted climate change, researchers should provide a deeper understanding of microclimatic conditions and outdoor thermal comfort in Australia and New Zealand. The study’s objectives can be classified into three categories: (1) to analyze previous research works on urban microclimate and outdoor thermal comfort in Australia and New Zealand; (2) to highlight the gaps in urban microclimate studies and (3) to provide a summary of recommendations for the neglected but critical aspects of urban microclimate.

The findings of this study indicate that, despite the various climate challenges in these countries, there has been limited investigation. According to the selected papers, Melbourne has the highest number of microclimatic studies among various cities. It is a significant area for past researchers to examine people’s thermal perceptions in residential areas during the summer through field measurements and surveys. An obvious gap in previous research is investigating the impacts of various urban contexts on microclimatic conditions through software simulations over the course of a year and considering the predicted future climate changes in these countries.

This paper aims to review existing studies in these countries, provide a foundation for future research, identify research gaps and highlight areas requiring further investigation.

The purpose of this study is to reveal the underlying mechanism in film formation of oil-in-water (O/W) emulsion.

This study focuses on the film forming characteristics of O/W emulsion between the surface of a steel ball and a glass disc coated with chromium. The lubricant film thicknesses of O/W emulsion with various mechanical stirring strength were discussed, which were observed by technique of relative optical interference intensity.

The authors directly observed the oil pool in the contact area, finding the size of oil pool was closely related to the film-forming ability of emulsion. Enrichment phenomenon occurs in oil pool, which was caused by phase inversion. Further investigations revealed that the emulsion is stable with strong stirring strength, resulting in a smaller oil pool size and worse film forming ability.

With the wide usage of O/W emulsion in both biological and industrial systems, the ability of emulsion film formation is considered as an important factor to evaluate the lubrication effectiveness.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2022-0354/

Mycelium is an upcoming bio-based alternative material that has various applications in different industries. Mycelium materials used as composites, leather, construction materials and some are even available for commercial purposes. However, there was not much research found when it came to the application of mycelium as a textile alternative. The purpose of this paper is to examine the potential of mycelium in the textile industry and its possible applications.

This review consolidates literature that refers the two major methods used in fungal mycelium production namely; as a composite and as a pure self-grown mycelium sheet. The study compared the current research status in this respective field and reported the scope in the pure mycelium development.

The results of the review reported that several research works are performed in composite production with different feedstock. The production methods and product development steps were well established for several applications from home utilities to construction materials. Whereas, in the case of self-grown mycelium sheet production only limited research works were found. Though the possibilities of engineered composite sheets are developed with various properties, research on self-grown pure mycelium sheets are at infant stage. Sensitive production methods, lower tensile, tearing, poor handle properties with brittle structure and non-uniformity in thickness are noted as limitations. Sustainable nature, self-grown three-dimensional nano-fibril network with porous structure are found to be advantageous.

The solid culture method was identified as a potential method to develop a sheet-like self-grown mycelium with different dimensions. The review results clearly show the lack of research in the direct application of self-grown pure mycelium area concerning feedstock material, fungal species selection and characterization of the developed product. Addressing the existing limitations will yield a sustainable textile material for fashion and textile industry with great potential.

The purpose of this study is to investigate the errors arising from the numerical treatment of model processes, paying particular attention to the impact of key system features including widely variable dispersion coefficients, spatiotemporal velocities of algal cells, and the aggregation of algae from single cells to large colonies. An advection–dispersion model has been presented to describe the vertical transport of colonial and motile harmful algae in a lake environment.

Model performance is examined for two different numerical treatments of the advective term: first-order upwind and quadratic upwind with a stability-preserving flux limiter (SMART). To determine how these schemes impact predictions, comparisons are made across a sequence of models with increasing complexity.

Using first-order upwinding for advection–dispersion calculations with a time oscillating velocity field leads to oscillatory numerical dispersion. Subjecting an initially uniform distribution of large-sized algal colonies to a spatiotemporal velocity creates a concentration pulse, which reaches a steady-state width at high-grid Peclet numbers when using the SMART scheme; the pulse exhibits contraction–expansion behavior throughout a velocity cycle at all Peclet numbers when using first-order upwinding. When aggregation dynamics are included with advection-dominated spatiotemporal transport, results indicate the SMART scheme predicts larger peak concentration values than those predicted by first-order upwind, but peak location and the time to large colony appearance remain largely unchanged between the two advective schemes.

To the best of the authors’ knowledge, this study is the first numerical investigation of a novel advection–dispersion model of vertical algal transport. In addition, a generalized expression for the effective dispersion coefficient of temporally variable flow fields is presented.

The purpose of this paper is to synthesize a polyacrylate-based dispersant with a determined target molecular weight for oily systems and to determine the optimal dispersant level and monomer ratio of the dispersant.

The dispersant was synthesized by conventional radical polymerization using methacrylic acid, butyl acrylate and dimethylamino ethyl methacrylate as the monomer. It was characterized by Fourier transform infrared spectroscopy, nuclear magnetic hydrogen spectroscopy, gel permeation chromatography and thermogravimetric analysis. The dispersant was used to disperse TiO₂, and the performance of the dispersant was evaluated by measuring the viscosity, particle size and dispersive force of the slurry.

The dispersant exhibited high thermal stability and was successfully anchored to the surface of the TiO₂ pigment. When used to disperse a TiO₂ slurry, it effectively made the TiO₂ slurry more fluid, indicating its strong viscosity-reducing properties. The viscosity, particle sizes and dispersion capabilities of the TiO₂ slurry were found to vary depending on the contents and monomer ratios of the dispersant.

P(MAA-BA-DM) dispersant increases the wettability of TiO₂ only in oily solvents but not in aqueous solvents.

P(MAA-BA-DM) dispersant makes it easier to disperse TiO₂ pigments in oily solvents, increasing the amount of pigment in the solvent and making the preparation of highly pigmented pastes easier.

A dispersant containing suitable carboxyl and tertiary amine groups was initially synthesized to disperse TiO₂ in an oily system. The findings are anticipated to be used in the formulation of pigment concentrates, industrial coatings and other solvent-based coatings.