Search results

1 – 10 of 59
Open Access
Article
Publication date: 27 June 2023

Farid Salari, Paolo Bosetti and Vincenzo M. Sglavo

Particles bed binding by selective cement activation (SCA) method is a computer-aided manufacturing (CAM) technique used to produce cementitious elements. A computer-aided design…

Abstract

Purpose

Particles bed binding by selective cement activation (SCA) method is a computer-aided manufacturing (CAM) technique used to produce cementitious elements. A computer-aided design file is sliced to generate G-codes before printing. This paper aims to study the effect of key input parameters for slicer software on the final properties of printed products.

Design/methodology/approach

The one factor at a time (OFAT) methodology is used to investigate the impact of selected parameters on the final properties of printed specimens, and the causes for the variations in outcomes of each variable are discussed.

Findings

Finer aggregates can generate a more compact layer, resulting in a denser product with higher strength. Fluid pressure is directly determined by voxel rate (rV); however, high pressures enable better fluid penetration control for fortified products; for extreme rVs, residual voids in the interfaces between successive layers and single-line primitives impair mechanical strength. It was understood that printhead movement along the orientation of the parts in the powder bed improved the mechanical properties.

Originality/value

The design of experiment (DOE) method assesses the influence of process parameters on various input printing variables at the same time. As the resources are limited, a fractional factorial plan is carried out on a subset of a full factorial design; hence, providing physical interpretation behind changes in each factor is difficult. OFAT aids in analyzing the effect of a change in one factor on output while all other parameters are kept constant. The results assist engineers in properly considering the influence of variable variations for future DOE designs.

Details

Rapid Prototyping Journal, vol. 29 no. 11
Type: Research Article
ISSN: 1355-2546

Keywords

Content available
Article
Publication date: 15 February 2022

Md. Hazrat Ali, Gani Issayev, Essam Shehab and Shoaib Sarfraz

In recent years, 3D printing technologies have been widely used in the construction industry. 3D printing in construction is very attractive because of its capability of process…

3249

Abstract

Purpose

In recent years, 3D printing technologies have been widely used in the construction industry. 3D printing in construction is very attractive because of its capability of process automation and the possibility of saving labor, waste materials, construction time and hazardous procedures for humans. Significant researches were conducted to identify the performance of the materials, while some researches focused on the development of novel techniques and methods, such as building information modeling. This paper aims to provide a detailed overview of the state-of-the-art of currently used 3D printing technologies in the construction areas and global acceptance in its applications.

Design/methodology/approach

The working principle of additive manufacturing in construction engineering (CE) is presented in terms of structural design, materials used and theoretical background of the leading technologies that are used to construct buildings and structures as well as their distinctive features.

Findings

The trends of 3D printing processes in CE are very promising, as well as the development of novel materials, will gain further momentum. The findings also indicate that the digital twin (DT) in construction technology would bring the industry a step forward toward achieving the goal of Industry 5.0.

Originality/value

This review highlights the prospects of digital manufacturing and the DT in construction engineering. It also indicates the future research direction of 3D printing in various constriction sectors.

Details

Rapid Prototyping Journal, vol. 28 no. 7
Type: Research Article
ISSN: 1355-2546

Keywords

Open Access
Article
Publication date: 25 July 2022

Cara Greta Kolb, Maja Lehmann, Johannes Kriegler, Jana-Lorena Lindemann, Andreas Bachmann and Michael Friedrich Zaeh

This paper aims to present a requirements analysis for the processing of water-based electrode dispersions in inkjet printing.

907

Abstract

Purpose

This paper aims to present a requirements analysis for the processing of water-based electrode dispersions in inkjet printing.

Design/methodology/approach

A detailed examination of the components and the associated properties of the electrode dispersions has been carried out. The requirements of the printing process and the resulting performance characteristics of the electrode dispersions were analyzed in a top–down approach. The product and process side were compared, and the target specifications of the dispersion components were derived.

Findings

Target ranges have been identified for the main component properties, balancing the partly conflicting goals between the product and the process requirements.

Practical implications

The findings are expected to assist with the formulation of electrode dispersions as printing inks.

Originality/value

Little knowledge is available regarding the particular requirements arising from the systematic qualification of aqueous electrode dispersions for inkjet printing. This paper addresses these requirements, covering both product and process specifications.

Details

Rapid Prototyping Journal, vol. 28 no. 11
Type: Research Article
ISSN: 1355-2546

Keywords

Open Access
Article
Publication date: 16 November 2023

Tao Wang, Shaoliang Wu, Hengqiong Jia, Zhao Wei, Haiyan Li, Piyan Shao, Shanqing Peng and Yi Shi

The construction of cement asphalt (CA) emulsified mortar can obviously disturb the slab status after the fine adjustment. To decrease or eliminate the influence of CA mortar…

120

Abstract

Purpose

The construction of cement asphalt (CA) emulsified mortar can obviously disturb the slab status after the fine adjustment. To decrease or eliminate the influence of CA mortar grouting on track slab geometry status, the effects of grouting funnel, slab pressing method, mortar expansion ratio, seepage ratio and grouting area on China Railway Track System Type (CRTS I) track slab geometry status were discussed in this paper.

Design/methodology/approach

Combined with engineering practice, this paper studied the expansion law of filling layer mortar, the liquid level height of the filling funnel, the pressure plate device and the amount of exudation water and systematically analyzed the influence of filling layer mortar construction on the state of track slab. Relevant precautions and countermeasures were put forward.

Findings

The results showed that the track slab floating values of four corners were different with the CA mortar grouting and the track slab corner near CA mortar grouting hole had the maximum floating values. The anti-floating effect of “7” shaped slab pressing device was more efficient than fixed-joint angle iron, and the slab floating value could be further decreased by increasing the amount of “7” shaped slab pressing devices. After CA mortar grouting, the track slab floating pattern had a close correlation with the expansion rate and water seepage rate of CA mortar over time and the expansion and water seepage rate of the mortar were faster when the temperature was high. Furthermore, the use of strip CA mortar filling under the rail bearing platform on both sides could effectively reduce the float under the track slab, and it could also save mortar consumption and reduce costs.

Originality/value

This study plays an important role in controlling the floating values, CA mortar dosage and the building cost of projects by grouting CA mortar at two flanks of filling space. The research results have guiding significance for the design and construction of China's CRTS I, CRTS II and CRTS III track slab.

Details

Railway Sciences, vol. 2 no. 4
Type: Research Article
ISSN: 2755-0907

Keywords

Open Access
Article
Publication date: 19 March 2024

Feng Chen, Zhongjin Wang, Dong Zhang and Shuai Zeng

Explore the development trend of chemically-improved soil in railway engineering.

Abstract

Purpose

Explore the development trend of chemically-improved soil in railway engineering.

Design/methodology/approach

In this paper, the technical standards home and abroad were analyzed. Laboratory test, field test and monitoring were carried out.

Findings

The performance design system of the chemically-improved soil should be established.

Originality/value

On the basis of the performance design, the test methods and standards for various properties of chemically-improved soil should be established to evaluate the improvement effect and control the engineering quality.

Details

Railway Sciences, vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 2755-0907

Keywords

Open Access
Article
Publication date: 13 March 2024

Tao Wang, Shaoliang Wu, Hengqiong Jia, Shanqing Peng, Haiyan Li, Piyan Shao, Zhao Wei and Yi Shi

During the construction process of the China Railway Track System (CRTS) I type filling layer, the nonwoven fabric bags have been used as grouting templates for cement asphalt…

Abstract

Purpose

During the construction process of the China Railway Track System (CRTS) I type filling layer, the nonwoven fabric bags have been used as grouting templates for cement asphalt (CA) emulsified mortar. The porous structure of nonwoven fabrics endowed the templates with breathability and water permeability. The standard requires that the volume expansion rate of CA mortar must be controlled within 1%–3%, which can generate expansion pressure to ensure that the cavities under track slabs are filled fully. However, the expansion pressure caused some of the water to seep out from the periphery of the filling bag, and it would affect the actual mix proportion of CA mortar. The differences in physical and mechanical properties between the CA mortar under track slabs and the CA mortar formed in the laboratory were studied in this paper. The relevant results could provide important methods for the research of filling layer materials for CRTS I type and other types of ballastless tracks in China.

Design/methodology/approach

During the inspection of filling layer, the samples of CA mortar from different working conditions and raw materials were taken by uncovering the track slabs and drilling cores. The physical and mechanical properties of CA mortar under the filling layer of the slab were systematically analyzed by testing the electrical flux, compressive strength and density of mortar in different parts of the filling layer.

Findings

In this paper, the electric flux, the physical properties and mechanical properties of different parts of CA mortar under the track slab were investigated. The results showed that the density, electric flux and compressive strength of CA mortar were affected by the composition of raw materials for dry powders and different parts of the filling layer. In addition, the electrical flux of CA mortar gradually decreased within 90 days’ age. The electrical flux of samples with the thickness of 54 mm was lower than 500 C. Therefore, the impermeability and durability of CA mortar could be improved by increasing the thickness of filling layer. Besides, the results showed that the compressive strength of CA mortar increased, while the density and electric flux decreased gradually, with the prolongation of hardening time.

Originality/value

During 90 days' age, the electrical flux of the CA mortar gradually decreased with the increase of specimen thickness and the electrical flux of the specimens with the thickness of 54 mm was lower than 500 C. The impermeability and durability of the CA mortar could be improved by increasing the thickness of filling layer. The proposed method can provide reference for the further development and improvement of CRTS I and CRTS II type ballastless track in China.

Details

Railway Sciences, vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 2755-0907

Keywords

Open Access
Article
Publication date: 14 March 2022

Jamiu Adetayo Dauda, Suraj A. Rahmon, Ibrahim A. Tijani, Fouad Mohammad and Wakeel O. Okegbenro

The purpose of this study is to find the optimum design of Reinforced Concrete (RC) pile foundation to enable efficient use of structural concrete with greater consequences for…

1624

Abstract

Purpose

The purpose of this study is to find the optimum design of Reinforced Concrete (RC) pile foundation to enable efficient use of structural concrete with greater consequences for global environment and economy.

Design/methodology/approach

A non-linear optimisation technique based on the Generalised Reduced Gradient (GRG) algorithm was implemented to find the minimum cost of RC pile foundation in frictional soil. This was achieved by obtaining the optimum pile satisfying the serviceability and ultimate limit state requirements of BS 8004 and EC 7. The formulated structural optimisation procedure was applied to a case study project to assess the efficiency of the proposed design formulation.

Findings

The results prove that the GRG method in Excel solver is an active, fast, accurate and efficient computer programme to obtain optimum pile design. The application of the optimisation for the case study project shows up to 26% cost reduction compared to the conventional design.

Research limitations/implications

The design and formulation of design constraints will be limited to provisions of BS 8004 and EC 7.

Practical implications

Since the minimum quantity of concrete was attained through optimisation, then minimum cement will be used and thus result in minimum CO2 emission. Therefore, the optimum design of concrete structures is a vital solution to limit the damage to the Earth's climate and the physical environment resulting from high carbon emissions.

Originality/value

The current study considers the incorporation of different soil ground parameters in the optimisation process rather than assuming any pile capacity value for the optimisation process.

Details

Frontiers in Engineering and Built Environment, vol. 2 no. 3
Type: Research Article
ISSN: 2634-2499

Keywords

Open Access
Article
Publication date: 9 September 2022

Akka Habib, Bencharki Bouchaib and Said Housni

The objective of this article is to propose a panel of management performance evaluation indicators at operator level. This panel would be the tool to be made available to an…

1118

Abstract

Purpose

The objective of this article is to propose a panel of management performance evaluation indicators at operator level. This panel would be the tool to be made available to an observatory that should be set up by regulation. The proposal comes at the right time given that Morocco is planning a major reform of the sector very soon. A framework law has already been promulgated for this purpose (Law 51-21 relating to the reform of public establishments).

Design/methodology/approach

The proposed panel is the result of (1) a review of the literature dealing with public management theories, in particular those relating to industrial and commercial public services and whose character is captive. The management of the latter requires a great deal of caution to preserve their economic balance and consequently their sustainability. (2) A review of experiences of countries is chosen because of contextual their similarities with Morocco like France having a similar legal background, Tunisia and Algeria chosen for geographical and economic similarities. The British experience is also discussed for what it represents as a liberal model in the management of public water and sanitation services, as opposed to the German model also studied and which stands as the only country where the management of public services has almost always been a communal prerogative. The analysis of these models has made it possible to identify management evaluation practices that could be adapted to the Moroccan context. (3) Research work by practitioners and reports from specialized international institutions (International Water Association [IWA]). (4) A critical analysis of a multitude of management and activity reports from 12 autonomous authorities and 4 private delegates covering 16 million inhabitants of the urban environment. A total of 15 indicators are developed. They aim to assess the effectiveness of management in terms of saving drinking water and preserving the natural environment from the pollution of water resources.

Findings

Approximately, 15 indicators for assessing water resource management in public water and sanitation services are proposed. These indicators relate to the efficiency of pipe networks, the performance of storage systems and losses in users' homes. Indicators specific to liquid sanitation systems, particularly with regard to the control of wastewater overflows into the public highway and their treatment before discharge into the natural environment, are also proposed.

Research limitations/implications

The application of the results of this research could be confronted with its appropriation by the operators. Indeed, the investment involved in setting up the proposed evaluation system, as well as the conflict of interest that may arise in the process of formalizing and standardizing the system at the national level, may slow down the process of setting it up.

Practical implications

In practice, the implementation of a system for evaluating the performance of water resource management in public drinking water and liquid sanitation services would make it possible to optimize the volume of water to be mobilized. Substantial savings are expected both at the level of the resource itself and at the level of the investments that accompany the realization of the mobilization and distribution infrastructures. These savings will be very useful for the creation of other similar services and to serve more people.

Social implications

The distribution of drinking water and liquid sanitation is a vital human need. These services are extremely captive. They are key factors in the socioeconomic development of the territory and the citizen. The impact is transversal and affects the lifestyle of the populations. On the one hand, it favors the sedentarization of the populations and on the other hand, preserves their health by fighting against the diseases of water origin. In addition, the comfort that it provides in the daily life of users is highly coveted when they are delivered in a modern way and arranged with modern technologies.

Originality/value

The regulation of public drinking water and liquid sanitation services in Morocco is the weakest link in the sector. The Ministry of the Interior is legally responsible for setting up a standard system for evaluating the management of these services to fill this gap (organic law 113-14 on municipalities). Unfortunately, this initiative is not yet underway. The opportunity to apply the results of this research is well timed. Morocco plans to launch a global reform of the sector starting in 2022–2023 (Law 50-21 on the reform of public institutions).

Details

Arab Gulf Journal of Scientific Research, vol. 40 no. 3
Type: Research Article
ISSN: 1985-9899

Keywords

Open Access
Article
Publication date: 16 June 2021

Zrinka Buhin Šturlić, Mirela Leskovac, Krunoslav Žižek and Sanja Lučić Blagojević

The purpose of this paper is to prepare stabile emulsions with 0–15% of colloidal silica and high monomer/water ratio and to investigate the influence of silica addition and…

1151

Abstract

Purpose

The purpose of this paper is to prepare stabile emulsions with 0–15% of colloidal silica and high monomer/water ratio and to investigate the influence of silica addition and surface modification on the polyacrylate properties.

Design/methodology/approach

Improving the properties of the composite can be achieved by optimizing the compatibility between the phases of the composite system with improving the interactions at the matrix/filler interface. Therefore, the silica surface was modified with nonionic emulsifier octylphenol ethoxylate, cationic initiator 2,2'-azobis-(amidinopropane dihydrochloride) and 3-methacryloxypropyltrimethoxysilane and polyacrylate/silica nanocomposites were prepared via in situ emulsion polymerization. Particle size distribution, rheological properties of the emulsions and morphology, thermal properties and mechanical properties of the film prepared from the emulsions were investigated.

Findings

Polyacrylate/silica systems with unmodified silica, silica modified with nonionic emulsifier and cationic initiator have micrometer, while pure PA matrix and systems with silica modified with silane have nanometer particle sizes. Addition and surface modification of the filler increased emulsion viscosity. Agglomeration of silica particles in composites was reduced with silica surface modification. Silica filler improves thermal stability and tensile strength of polyacrylate.

Originality/value

This paper provides broad spectrum of information depending on filler surface modification and latex preparation via in situ emulsion polymerization and properties with high amount of filler and monomer/water ratio with the aim that prepared latex is suitable for film formation and final application.

Details

Pigment & Resin Technology, vol. 51 no. 2
Type: Research Article
ISSN: 0369-9420

Keywords

Open Access
Article
Publication date: 25 July 2019

Pathavee Waewwab, Sungsit Sungvornyothin, Kamolnetr Okanurak, Ngamphol Soonthornworasiri, Rutcharin Potiwat and Chadchalerm Raksakoon

The purpose of this paper is to investigate the influence of breeding containers on the production of Aedes mosquitoes after a vector-control program in households that might…

1828

Abstract

Purpose

The purpose of this paper is to investigate the influence of breeding containers on the production of Aedes mosquitoes after a vector-control program in households that might support dengue transmission in tourist attraction areas of Bang Kachao Riverbend, Thailand.

Design/methodology/approach

A cross-sectional study was conducted in an ecotourism area of Bang Kachao Riverbend, Thailand, during the period October 2016 to September 2017. A total of 832 households from five villages participated in the study. Data collection employed an interview questionnaire, larval mosquito survey and measurements of the chemical properties of the water in each container. A binary logistic regression model was used to investigate the characteristics of water containers influencing the presence or absence of Aedes immatures.

Findings

The study found that water containers located inside households had a highly presence of Aedes immatures (2.22 times) compared with outdoor containers. Water containers without lids and water containers with ineffective had a high presence of Aedes immatures (3.69 and 2.54 times, respectively). In addition, the chemical properties of the water inside the containers, such as pH, influenced the presence of Aedes immatures (1.76 times) (OR=1.76, 95% CI=1.59–1.96).

Originality/value

The study results emphasized the characteristics of water containers in households located in a tourist attraction area. The findings may inform public health vector-control messages for households located in the tourist attraction area.

Details

Journal of Health Research, vol. 33 no. 5
Type: Research Article
ISSN: 2586-940X

Keywords

1 – 10 of 59