Search results

This paper presents control strategy of VSC connected to the unbalanced grid in stationary coordinates system. The algorithm shown in the paper can be applied to typical inverter to reduce or even eliminate oscillation of DC‐link voltage under unbalanced operation. That has a direct influence on constant flow of p component of power which is essential for drives system for reducing torque ripples.

The presented strategy of control assumes that orientation of grid voltage and line current vectors hodographs have to be opposite. Mathematical analysis and simulation has been done. Laboratory tests on low power has also been carried out.

This method leads to fixed p component of power flow and fixed DC bus voltage. The presented idea of control may cause reduction of voltages asymmetry in three‐phase network with significant impedance (local grid, microgrid, isolated grid).

For 50 Hz power system, the presented control strategy has at least 5 ms response time because calculations are based on current and 5 ms delayed values of grid voltage. The paper presents only a simple steady state laboratory test that has been done in low scale of voltage and current.

The paper shows an example of implementation of the method with simple dead‐beat current controller based on DSP microprocessor. The algorithm can be easy applied in a DC/AC converter for elimination DC‐link oscillations under unbalanced working conditions.

Control methods presented in many other papers always provide sinusoidal, symmetrical three‐phase currents irrespective of grid voltage symmetry. The presented idea of control causes reduction of DC‐Link voltage and p, q components of power oscillations due to grid voltage asymmetry.

The purpose of this paper is to introduce a unique multilevel, one‐phase inverter (in the multiplied full‐bridge configuration, cascaded‐type) with unequal voltage distribution among the voltage levels.

Numerical and experimental results are discussed and the topology thereafter evaluated.

Unequal voltage distribution among voltage stages of the converter leads to increase of the output voltage resolution while simplifying the converter construction and minimizing the power switch losses. Simplorer numerical analyses as well as test stand measurements were led in order to verify properties of the system. Using the voltage distribution in the proportion of 6/2/1 leads to improved utilisation of power switches used in the means of voltage, current and switching frequency. FFT analysis was implemented in order to explore the frequency domain properties of the control apparatus.

The results allow improvement of power switch utilisation and output voltage resolution of cascaded, three‐stage multilevel converter topologies and voltage output filter optimisation for multilevel power electronic converters.

A new concept of voltage distribution is provided and described, a dedicated DSP‐based control system was developed as well as a small‐scale converter prototype, test stand measurement results are provided.

The purpose of this paper is to introduce an efficient model for analysis of the voltage distribution along the long ceramic insulator strings in a high‐voltage tower window, especially when the structure and parameters of the ceramic insulator are unknown. The effect of the grading ring on the voltage distribution is also investigated.

A circuit model composed of capacitors is used to analyze the voltage distribution along the ceramic insulator strings in a transmission tower window. The capacitances of the disk insulators, line conductors, and tower are obtained by using the finite element method, charge simulation method, boundary element method, and measurement according to their characteristics.

The model is very efficient. The voltage distribution along insulator strings can be optimized by adjusting the parameters of the grading ring. The maximum amount of voltage applied to a single insulator disk can be reduced effectively by increasing either the diameter of the grading ring or the distance from the upper surface of the grading ring to the high‐voltage end of the insulator string.

The model is very efficient for analysis of the voltage distribution along the long ceramic insulator strings, especially when the structure and parameters of the ceramic insulator are unknown.

The purpose of this paper is to consider a constructional solution of the combined instrument transformer: constructed so that the voltage part is a column transformer, which means that the magnetic circuit of it is open and situated into a composite insulator. The aim of this research was to achieve optimal configuration of open magnetic circuit of the column voltage transformer.

The authors made analyses of electromagnetic field distribution and computed the voltage error and phase displacement for many different cases of magnetic circuits of the column voltage transformers. The analyses of the electromagnetic field distribution and computations were carried out using the 3D field‐circuit method based on the finite‐element numerical method. The results were compared with tests of a real‐life model.

The result of research is the selection of the best constructional version of the column voltage transformer; the research also gives some guidelines for design and manufacture of this construction of combined transformers.

The paper is meant for constructors of instrument transformers and presents results of research into new constructional solutions of combined transformer.

This study aims to regarding the application of traditional pulse frequency modulation control full-bridge LLC resonant converters in wide output voltage fields such as on-board chargers, there are issues with wide frequency adjustment ranges and low conversion efficiency.

To address these issues, this paper proposes a fixed-frequency pulse width modulation (PWM) control strategy for a full-bridge LLC resonant converter, which adjusts the gain by adjusting the duty cycle of the switches. In the full-bridge LLC converter, the two switches of the lower bridge arm are controlled by a fixed-frequency and fixed duty cycle, with their switching frequency equal to the resonant frequency, whereas the two switches of the upper bridge arm are controlled by a fixed-frequency PWM to adjust the output voltage. The operation modes of the converter are analyzed in detail, and a mathematical model of the converter is established. The gain characteristics of the converter under the fixed-frequency PWM control strategy are deeply analyzed, and the conditions for implementing zero-voltage switching (ZVS) soft switching in the converter are also analyzed in detail. The use of fixed-frequency PWM control simplifies the design of resonant parameters, and the fixed-frequency control is conducive to the design of magnetic components.

According to the fixed-frequency PWM control strategy proposed in this paper, the correctness of the control strategy is verified through simulation and the development and testing of a 500-W experimental prototype. Test results show that the primary side switches of the converter achieve ZVS and the secondary side rectifier diodes achieve zero-current switching, effectively reducing the switching losses of the converter. In addition, the control strategy reduces the reactive circulating current of the converter, and the peak efficiency of the experimental prototype can reach 95.2%.

The feasibility of the fixed-frequency PWM control strategy was verified through experiments, which has significant implications for improving the efficiency of the converter and simplifying the design of resonant parameters and magnetic components in wide output voltage fields such as on-board chargers.

Electric spring (ES) is a demand response method that can stabilize the voltage of critical loads and improve power quality, especially in a weak power grid with a high proportion of renewable energy sources. Most of existing ESs are implemented by voltage-source inverter (VSI), which has some shortcomings. For example, the DC-link capacitor limits the service life of ES, and the battery is costly and hard to recycle. Besides, conventional VSI cannot boost the voltage, which limits the application of ES in high-voltage occasions. This study aims to propose a novel scheme of ES to solve the above problems.

In this work, an ES topology based on current-source inverter (CSI) without a battery is presented, and a direct current control strategy is proposed. The operating principles, voltage regulation range and parameter design of the proposed ES are discussed in detail.

The proposed ES is applicable to various voltage levels, and the harmonics are effectively suppressed, which have been validated via the experimental results in both ideal and distorted grid conditions.

An ES topology based on battery-less CSI is proposed for the first time, which reduces the cost and prolongs the service time of ES. A novel control strategy is proposed to realize the functions of voltage regulation and harmonic suppression.

Dielectric barrier discharge (DBD) is widely used in the treatment of skin disease, surface modification of material and other fields of electronics. The purpose of this paper is to design a high-performance power supply with a compact structure for excimer lamps in electronics application.

To design a high-performance power supply with a compact structure remains a challenge for excimer lamps in electronics application, a current-source type power supply in a single stage with power factor correction (PFC) is proposed. It consists of an excitation voltage generation unit and a PFC unit. By planning the modes of the excitation voltage generation unit, a bipolar pulse excitation voltage with a high rising and falling rate is generated. And a high power factor (PF) on the AC side is achieved by the interaction of a non-controlled rectifier and two inductors.

The experimental results show that not only a high-frequency and high-voltage bipolar pulse excitation voltage with a high average rising and falling rate (7.51GV/s) is generated, but also a high PF (0.992) and a low total harmonic distortion (5.54%) is obtained. Besides, the soft-switching of all power switches is realized. Compared with the sinusoidal excitation power supply and the current-source power supply, the proposed power supply in this paper can take advantage of the potential of excimer lamps.

A new high-performance power supply with a compact structure for DBD type excimer lamps is proposed. The proposed power supply can work stably in a wide range of frequencies, and the smooth regulation of the discharge power of the excimer lamp can be achieved by changing the switching frequency. The ideal excitation can be generated, and the soft switching can be realized. These features make this power supply a key player in the outstanding performance of the DBD excimer lamps application.

The purpose of this study is to model the dependences of the output voltage, temperature, current and electrical power dissipation of a voltage limiter based on a two-layer varistor–posistor structure on time and analysis the influence of operating modes and design parameters of such a limiter on these characteristics.

The behavior of the limiting voltage, temperature and other parameters of the voltage limiter when an input constant overvoltage is applied is studied by the simulation method. The voltage limiter was a two-layer construction. One layer was a zinc oxide ceramic varistor. The second layer was a posistor polymer composite with a nanocarbon filler of PolySwitch technology.

The output voltage across the varistor layer decreases and reaches some fixed value related to its breakdown voltage after applying a constant overvoltage to the structure over time. The temperature of the structure increases to some steady state value, while the current decreases significantly. The amplitude of the transient current pulse increases, its duration and energy of the transient process decrease with increasing overvoltage. An increase in the internal resistance of the overvoltage source can cause a decrease in the amplitude and an increase in the duration of transient currents.

The ranges of values for the activation energy of conduction of the varistor layer in weak electric fields, the intensity of heat exchange between the structure under study and the environment are determined to ensure the stable operation of this structure as a voltage limiter. The results obtained make it possible to select the necessary parameters of the indicated structures to ensure the required operating modes of the voltage limiter for various applications.

The purpose of this paper is to study the effects of voltage on microstructure and properties of micro-arc oxidation (MAO) ceramic coatings formed on AZ31B magnesium alloy under the constant current–constant voltage operation mode.

The wear and corrosion resistance of MAO coating on AZ31B magnesium alloy was studied by MAO in silicate electrolyte under constant current and constant voltage.

When the voltage is 360 V, the wear and corrosion resistance of AZ31B magnesium alloy is the best.

The wear and corrosion resistance of MAO coating on AZ31B magnesium alloy was studied by friction wear and electrochemical workstation.

This study aims to investigate the effect of electrodeposition parameters (i.e. time and voltage) on the properties of hydroxyapatite (HA) coating fabricated on Ti6Al4V surface.

A full factorial design along with response surface methodology was utilized to evaluate the main effect of independent variables and their relative interactions on response variables. The effect of electrodeposition voltage and deposition time on HA coatings Ca/P molar ratio and the size of deposited HA crystals were examined by structural equation modeling (SEM). The formation of plate-like and needle-like HA crystals was observed for all experiments.

The results obtained showed that the higher electrodeposition voltage leads to lower Ca/P values for HA coatings. This is more significant at lower deposition times, where at a 20-minute deposition time, the voltage increased from 2 to 3 V and the Ca/P decreased from 2.27 to 1.52. Full factorial design results showed that electrodeposition voltage has a more significant effect on the size of the deposited HA crystal. With increasing the voltage from 2 to 3 V at a deposition time of 20 min, the HA crystal size varied from 99 to 36 µm.

The investigation delved into the impact of two critical parameters, deposition time and voltage, within the electrodeposition process on two paramount properties of HA coatings. Analyzing the alterations in coating characteristics relative to variations in these process parameters can serve as a foundational guide for subsequent research in the domain of calcium-phosphate deposition for implants.