Search results

This paper aims to analyze deeply the effect of surface roughness conditions of the common interface of the two-layered riveted cantilever beams on their frictional damping during free lateral vibration at first mode. Here, the product, (µ × α), and damping ratio, ξ, are the parameters whose variations are analyzed in this investigation. For this, the influencing parameters considered are the natural frequency of vibration, f; the amplitude of initial excitation, y; and surface roughness value, Ra.

For experimentally evaluating logarithmic damping decrement, d, the frequency response function analyzer for the case of free lateral vibrations was used. Later, for evaluating the product, µ × α (where µ is the kinematic coefficient of friction and α is the dynamic slip ratio), and then, the damping ratio, ξ, the empirical relation suggested for logarithmic damping decrement, d, of riveted cantilever beams was used. After this, the full and reduced quadratic models of the product, µ × α, ξ, response surface methodology (RSM) with the help of Design Expert 11 software was used. Corresponding main effects plots, surface plots and prediction comparison plots were obtained to observe the variations of the product, µ × α, ξ for the variations of influencing parameters: f, y and Ra. Finally, a machine learning technique such as artificial neural networks (ANNs) using “nntool” present in MATLAB R13a software was used to predict the ξ for the different combinations of f, y and Ra.

The full and reduced quadratic regression models for the product, (µ × α) and the damping ratio, ξ of riveted cantilever beams for free lateral vibrations of the first mode in terms of the parameters: f, y and Ra were obtained. In addition, the main effects plots, surface plots and prediction comparison plots for the product, µ × α, ξ, with the corresponding experimental values of the product, µ × α, ξ, were obtained. Also, the execution of ANNs using MATLAB R13a software is proved to be the more accurate tool for the prediction of damping ratios in comparison to quadratic regression equations obtained from Design Expert 11 software. In the end, the assumption that the effect of surface roughness value on the product, (µ × α), and the damping ratio, ξ, is negligible is proved to be true using the main effects plots for the product, (µ × α) and ξ obtained from the Design Expert 11 software.

Obtaining the full and reduced quadratic regression equations for the product, (µ × α), and ξ of the two-layered riveted cantilever beams in terms of parameters: f, y and Ra was done. In addition, the conditions for the corresponding minimum and maximum values of the product, (µ × α), and ξ were obtained. Later, the main effects plots, surface plots and comparison plots of the predicted product, (µ × α), and ξ versus experimental product, (µ × α), and ξ were also obtained. Finally, the predicted values of the product, (µ × α), and ξ using the ANNs tool are observed to be the more accurate values in comparison to that obtained from RSM using the Design Expert 11 software.

This paper aims to study possible differences between the Outstanding Universal Value (OUV) defined in the designation of Cuenca as a World Heritage (WH) site and its inhabitants' perceptions of heritage value. The study is based on research conducted in the historic centre of Cuenca in Ecuador, which was accorded WH status in 1999.

The research employs both quantitative and qualitative methodologies, providing a complementary approach to the research subject. Quantitative research involved a probability survey of 400 informants randomly selected from the population of the canton of Cuenca, while qualitative research included 40 semi-structured interviews with residents and traders in the historic centre and 150 further written consultations with residents of the city.

Following the introduction, methodology and description, the paper presents the data gathered from the survey and interviews. These indicate inhabitants' perceptions of the meaning, values, and uses of WH in Cuenca and reveal differences between their perceptions and those of the official OUV.

Although there are several studies on WH residents' perceptions of UNESCO OUV, few highlight the mismatch between local community views of heritage and those established by UNESCO. This study reflects critically on the concept of OUV, which is based on technical and political criteria rather than social participation. The study employs methodologies that could be applied in other case studies and used to improve heritage management. This is the only study on local perceptions of Cuenca's OUV.

This research paper aims to analyze the scientific and grey literature on Quality 4.0 and zero-defect manufacturing (ZDM) frameworks to develop an integrated quality 4.0 framework (IQ4.0F) for quality improvement (QI) based on Six Sigma and machine learning (ML) techniques towards ZDM. The IQ4.0F aims to contribute to the advancement of defect prediction approaches in diverse manufacturing processes. Furthermore, the work enables a comprehensive analysis of process variables influencing product quality with emphasis on the use of supervised and unsupervised ML techniques in Six Sigma’s DMAIC (Define, Measure, Analyze, Improve and Control) cycle stage of “Analyze.”

The research methodology employed a systematic literature review (SLR) based on PRISMA guidelines to develop the integrated framework, followed by a real industrial case study set in the automotive industry to fulfill the objectives of verifying and validating the proposed IQ4.0F with primary data.

This research work demonstrates the value of a “stepwise framework” to facilitate a shift from conventional quality management systems (QMSs) to QMSs 4.0. It uses the IDEF0 modeling methodology and Six Sigma’s DMAIC cycle to structure the steps to be followed to adopt the Quality 4.0 paradigm for QI. It also proves the worth of integrating Six Sigma and ML techniques into the “Analyze” stage of the DMAIC cycle for improving defect prediction in manufacturing processes and supporting problem-solving activities for quality managers.

This research paper introduces a first-of-its-kind Quality 4.0 framework – the IQ4.0F. Each step of the IQ4.0F was verified and validated in an original industrial case study set in the automotive industry. It is the first Quality 4.0 framework, according to the SLR conducted, to utilize the principal component analysis technique as a substitute for “Screening Design” in the Design of Experiments phase and K-means clustering technique for multivariable analysis, identifying process parameters that significantly impact product quality. The proposed IQ4.0F not only empowers decision-makers with the knowledge to launch a Quality 4.0 initiative but also provides quality managers with a systematic problem-solving methodology for quality improvement.

Perceived benefits of building information modelling (BIM) have been discussed for some time, but cost–benefit benchmarking has been inconsistent. The purpose of this paper is to investigate BIM feasibility and evaluate investment worth to elucidate and develop the current understanding of BIM merit. The aim of the study is to propose a research agenda towards a more holistic perspective of BIM use incorporating quantifying investment return.

An in-depth examination of research patterns has been conducted to identify challenges in the assessment of the investment value and return on investment (ROI) for BIM in the construction industry. A total of 75 research articles were considered for the final literature review. An evaluation of the literature is conducted using a combination of bibliometric analysis and systematic reviews.

This study, which analysed 75 articles, unveils key findings in quantifying BIM benefits, primarily through ROI calculation. Two major research gaps are identified: the absence of a standardized BIM ROI method and insufficient exploration of intangible benefits. Research focus varies across phases, emphasizing design and construction integration and exploring post-construction phases. The study categorizes quantifiable factors, including productivity, changes and rework reduction, requests for information reduction, schedule efficiency, safety, environmental sustainability and operations and facility management. These findings offer vital insights for researchers and practitioners, enhancing understanding of ’BIM’s financial benefits and signalling areas for further exploration in construction.

The ’study’s outcomes offer the latest insights for researchers and practitioners to create effective approaches for quantifying ’BIM’s financial benefits. Additionally, the proposed research agenda aims to improve the current limited understanding of BIM feasibility and investment worth evaluation. Results of the study could assist practitioners in overcoming limitations associated with BIM investment and economic evaluations in the construction industry.

This paper aims to explore the impact of the data observation period on the computation of altmetric measures like velocity index (VI) and half-life. Furthermore, it also attempts to determine whether article-level computations are better than computations on the whole of the data for computing such measures.

The complete publication records for the year 2016 indexed in Web of Science and their altmetric data (original tweets) obtained from PlumX are obtained and analysed. The creation date of articles is taken from Crossref. Two time-dependent variables, namely, half-life and VI are computed. The altmetric measures are computed for all articles at different observation points, and by using whole group as well as article-level averaging.

The results show that use of longer observation period significantly changes the values of different altmetric measures computed. Furthermore, use of article-level delineation is advocated for computing different measures for a more accurate representation of the true values for the article distribution.

The analytical results show that using different observation periods change the measured values of the time-related altmetric measures. It is suggested that longer observation period should be used for appropriate measurement of altmetric measures. Furthermore, the use of article-level delineation for computing the measures is advocated as a more accurate method to capture the true values of such measures.

The research work suggests that altmetric mentions accrue for a longer period than the commonly believed short life span and therefore the altmetric measurements should not be limited to observation of early accrued data only.

The present study indicates that use of altmetric measures for research evaluation or other purposes should be based on data for a longer observation period and article-level delineation may be preferred. It contradicts the common belief that tweet accumulation about scholarly articles decay quickly.

Several studies have shown that altmetric data correlate well with citations and hence early altmetric counts can be used to predict future citations. Inspired by these findings, majority of such monitoring and measuring exercises have focused mainly on capturing immediate altmetric event data for articles just after the publication of the paper. This paper demonstrates the impact of the observation period and article-level aggregation on such computations and suggests to use a longer observation period and article-level delineation. To the best of the authors’ knowledge, this is the first such study of its kind and presents novel findings.

The role of customers has moved from reactive to proactive, and they require more control over digital touchpoints. The quest for authenticity is their response to the dark side of interactive marketing – forms of faking, manipulation and exploitation. Authenticity becomes a key topic in interactive marketing as it reflects how customers assess digital touchpoints. However, there is a lack of comprehensive knowledge of authenticity in the interactive environment.

This article consolidates the authenticity studies in various digital touchpoints using the entity-referent correspondence framework. This research employs bibliometric analysis and thematic analysis of 103 articles in the last 15 years.

Five research clusters are identified: (1) human, (2) brand-generated content, (3) user-generated content, (4) branded platforms and (5) new technologies-based touchpoints (artificial intelligence, augmented reality and virtual reality). Most interactive marketing studies focus on human and content authenticity, and new technologies-based touchpoints lack comprehensive conceptualization. The review synthesizes the types of authenticity used in each touchpoint and highlights the importance of true-to-creator-self and true-to-customer-self in customer evaluation. We further propose a research framework with four antecedent groups and outcomes.

Our research supports managers by highlighting the type of authenticity prioritized in each touchpoint's development.

To answer the call from interactive marketing researchers, this research highlights the distinct definitions of authenticity at various digital touchpoints rather than looking at the overall brand. Trends, gaps and future research agenda of the authenticity concept in technology adoption and customer behavior are discussed.

Avoided emissions refer to greenhouse gas emission reductions that are a result of using a product or are emission removals due to a decision or an action. Although there is no uniform standard for calculating avoided emissions, market actors have started referring to avoided emissions as “Scope 4” emissions. By default, making a claim about Scope 4 emissions gives an appearance that this Scope of emissions is a natural extension of the existing and accepted Scope-based emissions accounting framework. The purpose of this study is to explore the implications of this assumed legitimacy.

Via a desktop review and interviews, we analyse extant Scope 4 company reporting, associated accounting methodologies and the practical implications of Scope 4 claims.

Upon examination of Scope 4 emissions and their relationship with Scopes 1, 2 and 3 emissions, we highlight a dynamic and interdependent relationship between quantification, commensuration and standardization in emissions accounting. We find that extant Scope 4 assessments do not fit the established framework for Scope-based emissions accounting. In line with literature on the territorializing nature of accounting, we call for caution about Scope 4 claims that are a distraction from the critical work of reducing absolute emissions.

We examine the implications of assumed alignment and borrowed legitimacy of Scope 4 with Scope-based accounting because Scope 4 is not an actual Scope, but a claim to a Scope. This is as an act of accounting territorialization.

The paper investigates if the process that led to the birth of the Euro Area had a significant impact in homogenizing the capital structure decisions of European firms since the first introduction of the common currency.

A large sample of firms was constructed, and a Tobit-censored regression model was utilized to investigate the determinants of firms' observed capital structures. The Black–Scholes–Merton model was used to infer market values of assets, as well as the volatility of those values, from the observed market values of equity and the corresponding volatility. The existing differences in national tax rules were considered for estimating firm-specific marginal tax rates.

It was found that, despite the currency union and the institutional harmonization process, certain factors still play a different role. In particular, the impact of profitability is consistent with the pecking order view in some countries, and with the trade-off theory in others. Assets risk, measured as the annualized volatility of the market enterprise value, is the best predictor of observed leverage ratios. The sector of activity is significant in determining leverage decisions even when assets' risk is taken into account. Despite the monetary union and the increased financial and institutional integration in the Euro Area, the country of origin still plays a significant role in capital structure decisions, suggesting that other country-level factors may affect firms' financing behaviour.

The paper indicates that, despite the long harmonization process of institutions, regulations and public budget required to join the Euro, firms' financing decisions are still affected by country-specific factors once the common currency is introduced. Therefore, new entrant countries in the Euro area should not expect their companies to immediately conform with those located in other countries within the common currency area.

This article investigated the impact of the currency change from national currencies to the Euro on the determinants of capital structure choices. It was shown that, despite the long harmonization process that led to the birth of the Euro Area, national factors still affect firms' financing decisions. This provides guidance for policymakers in countries that are planning to join the Euro about the impact this will have on firms' financing decisions in the entrant country.

In this digital era, email is the most pervasive form of communication between people. Many users become a victim of spam emails and their data have been exposed.

Researchers contribute to solving this problem by a focus on advanced machine learning algorithms and improved models for detecting spam emails but there is still a gap in features. To achieve good results, features also play an important role. To evaluate the performance of applied classifiers, 10-fold cross-validation is used.

The results approve that the spam emails are correctly classified with the accuracy of 98.00% for the Support Vector Machine and 98.06% for the Artificial Neural Network as compared to other applied machine learning classifiers.

In this paper, Point-Biserial correlation is applied to each feature concerning the class label of the University of California Irvine (UCI) spambase email dataset to select the best features. Extensive experiments are conducted on selected features by training the different classifiers.

The heritage and tourist attractiveness of Heritage Cities have aroused interest in establishing mechanisms to enhance their value based on the development of sustainability policies. The socioeconomic and socioenvironmental valuation of these heritage sites has become a necessary tool for decision-making.

Following the recommendations of International Council on Monuments and Sites – ICOMOS, this paper proposes a series of indicators and an exploratory model to define the factors that contribute to their valuation. Following the partial least squares structural equation modelling methodology, information was obtained from 363 intramural residents in the three Heritage Cities that currently have management plans in Spain.

The results show the importance of specifying indicators of sustainable mobility and socioeconomic and socioenvironmental sustainability for an adequate valorisation of heritage sites.

To this end, it is necessary to follow the guidelines of international bodies such as ICOMOS in relation to the management plans.