Search results

Epoxy (EP) and polye-caprolactone (PCL) are typical dual-shape memory polymer (DSMP). To get excellent triple-shape memory effect (TSME) polymer composites which are made from EP and PCL. Miscible PCL/EP blend composites have been investigated and compared to the TSMEs with electrospun PCL microfiber membranes/EP composites. Clay montmorillonite (MMT)-modified electrospun PCL microfiber membranes were prepared to improve the shape memory fixities of electrospun PCL microfiber membranes/EP composites.

The morphologies of electrospun PCL microfiber membranes and the cross section of PCL/EP composites were studied using a field emission scanning electron microscope (FE-SEM), and the existence of MMT was confirmed by a transmission electron microscope. Thermal mechanical properties were observed by a differential scanning calorimeter (DSC) and a dynamic thermomechanical analysis machine, and the TSMEs were also determined through dynamic mechanical analysis.

Results indicate that the TSMEs of electrospun PCL microfiber membranes/EP composites were excellent, whereas the TSMEs of PCL/EP blend composites were poor. The TSMEs of PCL electrospun microfiber membranes/EP composites significantly improved with the addition of the PCL electrospun microfiber modified with moderate MMT.

Adding a moderate content of MMT into the electrospun PCL fibers, could improve the TSME of the PCL fiber membranes/EP composites. This study was to create a simple and effective method that can be applied to improve the performance of other SMP.

A novel triple-shape memory composite were made from dual-shape memory EP and electrospun PCL fiber membranes.

This paper aims to focus on achieving triple-shape memory effect (triple-SME) of a commercial poly (ethylene terephthalate) (PET) film with the thickness of 100 µm.

The thermal characteristics and microstructure of PET film were characterized by differential scanning calorimetry, thermogravimetric analysis and wide-angle X-ray diffraction analysis. The dual-shape memory effect (dual-SME) of the PET film was then systematically investigated, and based on that, triple-SME in thin PET film was achieved.

Investigation of the dual-SME in PET film revealed the difference between recovery temperature and programming temperature reduced with increasing programming temperature. An obvious intermediate shape shifting between the original and final programmed shape was observed during shape recovery in triple-shape memory behaviors.

Compared with dual-SME in polymer, relatively less work has been done on multi-SME in polymer, especially in thin polymer film. In this study, triple-SME in a PET film was investigated based on the results of dual-SME of the film. The main implication of the study is on how to achieve a watermark between the final programmed pattern and the original pattern, for the application of shape memory polymer in anti-counterfeiting label.

Dual- and triple-SMEs were achieved in a PET film that is only 100 µm in thickness, and the underlying mechanism for the difference between programming temperature and recovery temperature was discussed. For the novel application of triple-SME in anti-counterfeit label, the watermark during shape recovery in triple-SME can effectively prevent duplication.

This paper aims to present a review on utilizing shape memory technology (SMT) for active assembly/disassembly, i.e. assembly/disassembly without physically touching.

The fundamentals behind the shape memory effect (SME) in materials, in particular shape memory alloys (SMAs) and polymers, which are the cornerstones of SMT, are introduced, together with the possible approaches to implement this effect in active assembly/disassembly. Example applications for not only active assembly/ disassembly, but also programmed active disassembly are presented.

The advantages of utilizing SMT over conventional assembly/disassembly techniques are identified.

The paper introduces the fundamentals behind the SME and the basic approaches to implement the SMT in not only active assembly/disassembly, but also programmed active assembly.

Shape memory polymers (SMPs) respond with a change in their shape against a specific stimulus by memorizing their original shape and are reformed after deformation most often by changing the temperature of the surrounding without additional mechanical efforts. In the coming years, these polymers indeed will be in limelight to manufacture textile materials which will retain their shape even after prolonged use under disturbed conditions. This study aims at defining shape memory materials and polymers as well as their technological characteristics and also highlights application in various fields of textiles.

The methodology used to explain these SMPs have been carried out starting with the discussion on their properties, their physical nature, types, viz., shape memory alloys (SMAs), shape memory ceramics, shape memory hybrid, magnetic shape memory alloy, shape memory composites, shape memory gels and SMP along with properties of each type. Other related details of these polymers, such as their advantages, structure and mechanism, shape memory functionality, thermally responsive SMPs and applications, have been detailed.

It has been observed that the SMPs are very important in the fields of wet and melt-spun fibers to offer novel and functional properties, cotton and wool fabric finishing, to produce SMP films, foams and laminated textiles, water vapor permeable and breathable SMP films, etc.

The field of SMPs is new, and very limited information is available to enable their smooth production and handling.

This study aims to discuss the effect of carbon fiber on the electric-respone of shape memory epoxy property. Epoxy (EP) is a typical excellent thermosetting shape memory polymer (SMP). To enrich the shape memory epoxy (SMEP) responsive mode, the carbon fiber fabric-reinforced SMEP composites were prepared, and the mechanical properties and the electric- and light-responsive shape memory effect of the composites were investigated and confirmed.

The carbon fiber fabric/SMEP composites were prepared via a dipping method. The carbon fiber fabric was dipped into the waterborne epoxy emulsion and dried at room temperature and then post-cured in the oven at 120 °C for 2 h. The mechanical properties and the multi-responsive shape memory properties of the composites were tested and confirmed via tensile test instrument, DC electrical source and near-infrared (NIR) laser source control system.

The carbon fiber fabric/SMEP composites showed excellent electric- and light-responsive shape memory effect.

High performance and multi-responsive shape memory materials have always been the goal of the scientists. Carbon fiber fabric and SMEP both consist of a good reputation in the field of composites, and the combination of both would set a solid foundation for getting a high performance and multi-responsive shape memory effect materials, which will enrich the responsive mode and broaden the application of SMEP.

Multi-responsive SMEP composites were prepared from waterborne epoxy and carbon fiber fabric.

The purpose of this paper is to provide a review of recent systematic and comprehensive advancement in electrospun polymer fiber and their composites with shape memory property.

The nanofiber manufacture technique is initially reviewed. Then, the influence of electrospinning parameters and actuation method has been discussed. Finally, the study concludes with a brief review of recent development in potential applications.

Shape memory polymer (SMP) nanofibers are a type of smart materials which can change shape under external stimuli (e.g. temperature, electricity, magnetism, solvent). In general, such SMP nanofibers could be easily fabricated by mature electrospinning technique. The nanofiber morphology is mainly affected by the electrospinning parameters, including applied voltage, tip-to-collector distance, viscosity of solution, humidity and molecular weight. For actuation method, most SMP nanofibers and their composites can change their shapes in response to heat, magnetic field or solvent, while few can be driven by electricity. Compared with the block SMPs, electrospun SMP nanofibers’ mat with porosity and low mechanical property have a wide potential application field including tissue engineering, drug delivery, filtration, catalysis.

This paper provides a detailed review of shape memory nanofibers: fabrication, actuation and potential application, in the near future.

This paper aims to study the effect of microcrystalline cellulose (MCC) on the mechanical property and shape memory property of water-borne epoxy (WEP).

In the present study, the MCC/WEP composites were successfully prepared by melt-blending, freeze-drying and hot-pressing. The mechanical property tests were performed using a tensile test instrument (Instron Corp, Norwood, Massachusetts, USA). dynamic mechanical analysis Q800 was performed to analyze the sample’s dynamic mechanics. The thermal–mechanical cycle tests performed on a thermal mechanical analysis (TMA) Q400 in dynamic TMA mode enabled to analysis of the shape memory properties of the MCC/WEP composites.

The results showed that the inclusion of 2 wt.% MCC led to significant improvements in tensile strength and modulus of the composites, with tensile strength increasing by 33.2% and modulus expanding by 65.0%. Although the inclusion of the MCC into WEP enhanced the shape memory property, the MCC/WEP composites still maintained good shape memory fixity and shape memory recovery ratio of more than 95.0%.

This study has a significant reference value for improving the mechanical properties of WEP and other water-borne shape memory polymers.

This paper aims to provide a review of four-dimensional (4D) printing using fused-deposition modeling (FDM). 4D printing is an emerging innovation in (three-dimensional) 3D printing that encompasses active materials in the printing process to create not only a 3D object but also a 3D object that can perform an active function. FDM is the most accessible form of 3D printing. By providing a review of 4D printing with FDM, this paper has the potential in educating the many FDM 3D printers in an additional capability with 4D printing.

This is a review paper. The approach was to search for and review peer-reviewed papers and works concerning 4D printing using FDM. With this discussion of the shape memory effect, shape memory polymers and FDM were also made.

4D printing has become a burgeoning area in addivitive manufacturing research with many papers being produced within the past 3-5 years. This is especially true for 4D printing using FDM. The key findings from this review show the materials and material composites used for 4D printing with FDM and the limitations with 4D printing with FDM.

Limitations to this paper are with the availability of papers for review. 4D printing is an emerging area of additive manufacturing research. While FDM is a predominant method of 3D printing, it is not a predominant method for 4D printing. This is because of the limitations of FDM, which can only print with thermoplastics. With the popularity of FDM and the emergence of 4D printing, however, this review paper will provide key resources for reference for users that may be interested in 4D printing and have access to a FDM printer.

Practically, FDM is the most popular method for 3D printing. Review of 4D printing using FDM will provide a necessary resource for FDM 3D printing users and researchers with a potential avenue for design, printing, training and actuation of active parts and mechanisms.

Continuing with the popularity of FDM among 3D printing methods, a review paper like this can provide an initial and simple step into 4D printing for researchers. From continued research, the potential to engage general audiences becomes more likely, especially a general audience that has FDM printers. An increase in 4D printing could potentially lead to more designs and applications of 4D printed devices in impactful fields, such as biomedical, aerospace and sustainable engineering. Overall, the change and inclusion of technology from 4D printing could have a potential social impact that encourages the design and manufacture of such devices and the treatment of said devices to the public.

There are other 4D printing review papers available, but this paper is the only one that focuses specifically on FDM. Other review papers provide brief commentary on the different processes of 4D printing including FDM. With the specialization of 4D printing using FDM, a more in-depth commentary results in this paper. This will provide many FDM 3D printing users with additional knowledge that can spur more creative research in 4D printing. Further, this paper can provide the impetus for the practical use of 4D printing in more general and educational settings.

Polyethylene terephthalate (PET) as a fiber molding polymer is widely used in aerospace, electrical and electronic, clothing and other fields. The purpose of this study is to improve the thermal insulation performance of polyethylene terephthalate (PET), the SiO₂ aerogel/PET composites slices and fibers were prepared, and the effects of the SiO₂ aerogel on the morphology, structure, crystallization property and thermal conductivity of the SiO₂ aerogel/PET composites slices and their fibers were systematically investigated.

The mass ratio of purified terephthalic acid and ethylene glycol was selected as 1:1.5, which was premixed with Sb₂O₃ and the corresponding mass of SiO₂ aerogel, and SiO₂ aerogel/PET composites were prepared by direct esterification and in-situ polymerization. The SiO₂ aerogel/PET composite fibers were prepared by melt-spinning method.

The results showed that the SiO₂ aerogel was uniformly dispersed in the PET matrix. The thermal insulation coefficient of PET was significantly reduced by the addition of SiO₂ aerogel, and the thermal conductivity of the 1.0 Wt.% SiO₂ aerogel/PET composites was reduced by 75.74 mW/(m · K) compared to the pure PET. The thermal conductivity of the 0.8 Wt.% SiO₂ aerogel/PET composite fiber was reduced by 46.06% compared to the pure PET fiber. The crystallinity and flame-retardant coefficient of the SiO₂ aerogel/PET composite fibers showed an increasing trend with the addition of SiO₂ aerogel.

The SiO₂ aerogel/PET composite slices and their fibers have good thermal insulation properties and exhibit good potential for application in the field of thermal insulation, such as warm clothes. In today’s society where the energy crisis is becoming increasingly serious, improving the thermal insulation performance of PET to reduce energy loss will be of great significance to alleviate the energy crisis.

In this study, SiO₂ aerogel/PET composite slices and their fibers were prepared by an in situ polymerization process, which solved the problem of difficult dispersion of nanoparticles in the matrix and the thermal conductivity of PET significantly reduced.

This paper aims to investigate the effects on material performance in the epoxy acrylate resin system owing to the existence of the different ring of the cyclic methacrylate. In this paper, cyclic methacrylate as diluents was added into epoxy acrylate (EA) resin by ultraviolet (UV)-cured polymerization to investigate the effects on material performance owing to the existence of the different rings.

EA and 1-adamantyl methacrylate were synthesized by traditional methods according to previous papers, respectively. After adding different cyclic methacrylate as diluents to the EA oligomers, the system was exposed to the UV-light for polymerization.

The hydrophobic properties of the cured materials were increased slightly because of the alkyl groups from the methacrylate. The thermal stabilities and mechanical properties of the resins were enhanced by the cyclic diluents with the hard segments. Meanwhile, the crosslink density of the polymer decreased with the bulky group like adamantly owing to its huge structure.

The cyclic methacrylates were introduced into EA oligomers for decreasing the viscosity and increasing the materials performances, which could be recognized as new diluents applied in UV-cued polymerization.

The results of this study will be conducive to fabricate EA resins possessed with high thermal stabilities and mechanical properties by convenient UV-cured polymerization.