Search results

Instantaneous unloading with equal force is usually used to simulate the sudden failure of cables. This simulation method with equivalent force requires obtaining the magnitude and direction of the force for the failed cable in the normal state. It is difficult, however, to determine the magnitude or direction of the equivalent force when the shape of the cable is complex (space curve). This model of equivalent force may be difficult to establish. Thus, a numerical simulation method, the instantaneous temperature rise method, was proposed to address the dynamic response caused by failures of the cables with complex structural form.

This method can instantly reduce the cable force to zero through the instantaneous temperature rise process of the cable. Combined with theoretical formula and finite element model, the numerical calculation principle and two key parameters (temperature rise value and temperature rise time) of this method were detailed. The validity of this approach was verified by comparing it with equivalent force models. Two cable-net case with saddle curved surfaces were presented. Their static failure behaviors were compared with the dynamic failure behaviors calculated by this method.

This simulation method can effectively address the structural dynamic response caused by cable failure and may be applied to all cable structures.

An instantaneous temperature rise method (ITRM) is proposed and verified. Its calculation theory is detailed. Two key parameters, temperature rise value and temperature rise time, of this method are discussed and the corresponding reference values are recommended.

Due to high speeds, heavy loads, large slide-to-roll ratios (SRR) and other variable operating conditions, some rolling bearings that have been working in harsh conditions may experience flash temperatures in the contact area, which may result in early damage like smearing and then affect service life. This study aims to investigate the flash temperature phenomenon of rolling bearings through theoretical and experimental analysis.

A technology for measuring temperature distribution in rolling ball on disk contact under lubrication was developed. The test-rig can simulate the ball bearing contact. The effects of working conditions such as entrainment speed, load, SRR and lubricating oil viscosity on the flash temperature were investigated.

The results of the theoretical calculation and experiments indicate that the parameters promoting the reduction of film thickness in elastohydrodynamic lubrication are always related with the number of flash points, even film thickness reduced to mixed lubrication. The flash temperature is easier to happen in conditions of high SRR, heavy load, slow entrainment speed and low viscosity oil.

This work conducts an experimental study on the flash temperature phenomenon, providing a test technology for bearing lubrication and failure investigation.

This author has opted into Transparent Peer Review available at: https://publons.com/publon/10.1108/ILT-04-2023-0104

This study examines the evidence of the impact of climate change on the financial performance of basic materials companies in Vietnam.

The research sample includes eighty-two basic materials companies listed on the Vietnamese stock market from 2003 to 2022. This study used one-way and two-way fixed-effects feasible generalized least squares (FGLS) estimation methods.

Climate change, measured through variables including changes in temperature, average rainfall, greenhouse gas emissions and rising sea levels, has a negative impact on the financial performance of companies in this industry. The study also found that, with rising temperatures, the financial performance of steel manufacturing companies decreased less than that of coal mining and forestry companies, but increasing greenhouse gases and rising sea levels reduced the financial performance of steel companies. We did not find evidence of any difference in the impact of climate change on the financial performance of basic materials companies before and after the UN Climate Change Conference (COP 21). This is a new finding, which is consistent with empirical studies in Vietnam and different from previous studies in that it provides new evidence on the impact of climate change on the financial performance of basic materials companies in the Vietnamese market and cross-checks the impact of climate change by sector and over time.

To the best of our knowledge, this is one of the first articles on climate change and the financial performance of basic materials companies.

This paper aims to study the deformation mechanism of polytetrafluoroethylene (PTFE) oil seal under a wide temperature range cycle.

This study categorizes the oil seal operation into three states: assembly, heating-up and cooling. The deformation equation for the oil seal is developed for each state, considering the continuity between them. The investigation of the oil seal’s deformation trends and mechanisms is performed using the ANSYS Workbench.

The assembling process results in a radial shrinkage of the skeleton, causing the centroid to move toward the axis. During heating-up, the outer diameter of the skeleton slightly expands, whereas the inner diameter sharply contracts toward the axis, leading to a further reduction in the centroid’s distance from the axis. Upon cooling, both the inner and outer diameters continue to contract toward the axis, causing the centroid to persist in its movement toward the axis. Consequently, after undergoing a heating-up and cooling cycle ranging from 20°C to 180°C, the outer diameter of the PTFE oil seal reduces by 0.92 mm from its original deformation, ensuring minimal contact between the skeleton and housing. As a result of the reduced static friction torque at the skeleton, the oil seal rotates along the shaft.

The deformation mechanism of PTFE oil seals under a wide temperature range cycle was investigated, aiming to address the concerns related to the rotation along the shaft and leakage.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2023-0142/

This study empirically examines the impact of climate change and agricultural research and development (R&D) as well as their interaction on agricultural productivity in 12 selected Asian and Pacific countries over the period of 1990–2018.

Various estimation methods for panel data, including Fixed Effects (FE), the Feasible Generalized Least Squares (FGLS) and two-step System Generalized Method of Moments (SGMM) were used.

Results show that both proxies of climate change – temperature and precipitation – have negative impacts on agricultural productivity. Notably, agricultural R&D investments not only increase agricultural productivity but also mitigate the detrimental impact of climate change proxied by temperature on agricultural productivity. Interestingly, climate change proxied by precipitation initially reduces agricultural productivity until a threshold of agricultural R&D beyond which precipitation increases agricultural productivity.

The findings imply useful policies to boost agricultural productivity by using R&D in the context of rising climate change in the vulnerable continent.

This study contributes to the literature in two ways. First, this study examines how climate change affects agricultural productivity in Asian and Pacific countries – those are most vulnerable to climate change. Second, this study assesses the role of R&D in improving agricultural productivity as well as its moderating effect in reducing the harmful impact of climate change on agricultural productivity.

To investigate the mechanical properties of geopolymer concrete at elevated temperatures.

The investigation involved studying the influence of partially replacing fly ash with ground granulated blast furnace slag (GGBS) at different proportions (5%, 10%, 15%, 20% and 25%) on the composition of the geopolymer. This approach aimed to examine how the addition of GGBS impacts the properties of the geopolymer material. The chemical NaOH was purchased from the local supplier of Jamshedpur. The alkali solution was prepared with a concentration of 12 M NaOH to produce the concrete. After several trials, the alkaline-to-binder ratio was determined to be 0.43.

The compressive strength values at 28 days for specimens FG1, FG2, FG3, FG4 and FG5 are 35.42 MPa, 41.26 MPa, 44.79 MPa, 50.51 MPa and 46.33 MPa, respectively. The flexural strength values at 28 days for specimens FG1, FG2, FG3, FG4 and FG5 are 5.31 MPa, 5.64 MPa, 6.12 MPa, 7.15 MPa and 6.48 MPa, respectively. The split tensile strength values at 28 days for specimens FG1, FG2, FG3, FG4 and FG5 are 2.82 MPa, 2.95 MPa, 3.14 MPa, 3.52 MPa and 3.31 MPa, respectively.

This approach allows for the examination of how the addition of GGBS affects the properties of the geopolymer material. Four different temperature levels were chosen for analysis: 100 °C, 300 °C, 500 °C and 700 °C. By subjecting the geopolymer samples to these elevated temperatures, the study aimed to observe any changes in their mechanical.

Combustion of fuel with oxidizer inside a combustion chamber of an internal combustion engine forms inevitable oxides of nitrogen (NOx) due to high temperature at different locations of the combustion chamber. This study aims to quantify NOx formed inside the combustion chamber using two fuels, a conventional diesel (n-heptane) and a biodiesel (methyl oleate).

This research uses a computational fluid dynamics simulation of chemically reacting fluid flow to quantify and compare oxides of nitrogen (NOx) in a compression ignition (CI) engine. The study expends species transport model of ANSYS FLUENT. The simulation model has provided the temperature profile inside the combustion chamber, which is subsequently used to calculate NOx using the NOx model. The simulation uses a single component hydrocarbon and oxygenated hydrocarbon to represent fuels; for instance, it uses n-heptane (C₇H₁₆) for diesel and methyl-oleate (C₁₉H₃₆O₂) for biodiesel. A stoichiometric air–fuel mixture is used for both fuels. The simulation runs a single cylinder CI engine of 650 cm³ swept volume with inlet and exhaust valves closed.

The pattern for variation of velocity, an important flow parameter, which affects combustion and subsequently oxides of nitrogen (NOx) formation at different piston locations, is similar for the two fuels. The variations of in-cylinder temperature and NOx formation with crank angles have similar patterns for the fuels, diesel and biodiesel. However, the numerical values of in-cylinder temperature and mass fraction of NOx are different. The volume averaged static peak temperatures are 1,013 K in case of diesel and 1,121 K in case of biodiesel, while the mass averaged mass fractions of NOx are 15 ppm for diesel and 141 ppm for biodiesel. The temperature rise after combustion is more in case of biodiesel, which augments the oxides of nitrogen formation. A new parameter, relative mass fraction of NOx, yields 28% lower value for biodiesel than for diesel.

This work uses a new concept of simulating simple chemical reacting system model to quantify oxides of NOx using single component fuels. Simplification has captured required fluid flow data to analyse NOx emission from CI engine while reducing computational time and expensive experimental tests.

Ohmic heating generates temperature with the help of electrical current and resists the flow of electricity. Also, it generates heat rapidly and uniformly in the liquid matrix. Electrically conducting biofluid flows with Ohmic heating have many biomedical and industrial applications. The purpose of this study is to provide the significance of the effects of Ohmic heating and viscous dissipation on electrically conducting Casson nanofluid flow driven by peristaltic pumping through a vertical porous channel.

In this analysis, the non-Newtonian properties of fluid will be characterized by the Casson fluid model. The long wavelength approach reduces the complexity of the governing system of coupled partial differential equations with non-linear components. Using a regular perturbation approach, the solutions for the flow quantities are established. The fascinating and essential characteristics of flow parameters such as the thermal Grashof number, nanoparticle Grashof number, magnetic parameter, Brinkmann number, permeability parameter, Reynolds number, Casson fluid parameter, thermophoresis parameter and Brownian movement parameter on the convective peristaltic pumping are presented and thoroughly addressed. Furthermore, the phenomenon of trapping is illustrated visually.

The findings indicate that intensifying the permeability and Casson fluid parameters boosts the temperature distribution. It is observed that the velocity profile is elevated by enhancing the thermal Grashof number and perturbation parameter, whereas it reduces as a function of the magnetic parameter and Reynolds number. Moreover, trapped bolus size upsurges for greater values of nanoparticle Grashof number and magnetic parameter.

There are some interesting studies in the literature to explain the nature of the peristaltic flow of non-Newtonian nanofluids under various assumptions. It is observed that there is no study in the literature as investigated in this paper.

Light emitting diode (LED) has been the best resource for commercial and industrial lighting applications. However, thermal management in high power LEDs is a major challenge in which the thermal resistance (R_th) and rise in junction temperature (T_J) are critical parameters. The purpose of this work is to evaluate the R_th and T_j of the LED attached with the modified heat transfer area of the heatsink to improve thermal management.

This paper deals with the design of metal substrate for heatsink applications where the surface area of the heatsink is modified. Numerical simulation on heat distribution proved the influence of the design aspects and surface area of heatsink.

T_J was low for outward step design when compared to flat heatsink design (ΔT ∼ 38°C) because of increase in surface area from 1,550 mm² (flat) to 3,076 mm² (outward step). On comparison with inward step geometry, the T_J value was low for outward step configuration (ΔT_J ∼ 6.6°C), which is because of efficient heat transfer mechanism with outward step design. The observed results showed that outward step design performs well for LED testing by reducing both R_th and T_J for different driving currents.

This work is authors’ own design and also has the originality for the targeted application. To the best of the authors’ knowledge, the proposed design has not been tried before in the electronic or LED applications.

In recent years, fire accidents in engineering structures have often been reported worldwide, leading to a severe risk to life and property safety. The present study is carried out to evaluate the performance of Ground Granulated Blast Furnace Slag (GGBS) and fly ash–blended laterized mortars at elevated temperatures.

This test program includes the replacement of natural river sand with lateritic fine aggregates (lateritic FA) in terms of 0, 50 and 100%. Also, the ordinary Portland cement (OPC) was replaced with fly ash and GGBS in terms of 10, 20, 30% and 20, 40 and 60%, respectively, for producing blended mortars.

This paper presents results related to the determination of residual compressive strengths of lateritic fine aggregates-based cement mortars with part replacement of cement by fly ash and GGBS exposed to elevated temperatures. The effect of elevated temperatures on the physical and mechanical properties was evaluated with the help of microstructure studies and the quantification of hydration products.

A sustainable cement mortar was produced by replacing natural river sand with lateritic fine aggregates. The thermal strength deterioration features were assessed by exposing the control specimens and lateritic fine aggregates-based cement mortars to elevated temperatures. Changes in the mechanical properties were evaluated through a quantitative microstructure study using scanning electron microscopy (SEM) images. The phase change of hydration products after exposure to elevated temperatures was qualitatively analyzed by greyscale thresholding of SEM images using Image J software.