Search results

1 – 10 of 345
Open Access
Article
Publication date: 1 June 2021

S.V. Khandal, T.M. Yunus Khan, Sarfaraz Kamangar, Maughal Ahmed Ali Baig and Salman Ahmed N J

The different performance tests were conducted on diesel engine compression ignition (CI) mode and CRDi engine.

1201

Abstract

Purpose

The different performance tests were conducted on diesel engine compression ignition (CI) mode and CRDi engine.

Design/methodology/approach

The CI engine was suitably modified to CRDi engine with Toroidal re-entrant combustion chamber (TRCC) and was run in dual-fuel (DF) mode. Hydrogen (H2) was supplied at different flow rates during the suction stroke, and 0.22 Kg/h of hydrogen fuel flow rate (HFFR) was found to be optimum. Diesel and biodiesel were used as pilot fuels. The CRDi engine with DF mode was run at various injection pressures, and 900 bar was found to be optimum injection pressure (IP) with 10o before top dead center (bTDC) as fuel injection timing (IT).

Findings

These operating engine conditions increased formation of oxides of nitrogen (NOx), which were reduced by exhaust gas recycle (EGR). With EGR of 15%, CRDi engine resulted in 12.6% lower brake thermal efficiency (BTE), 5.5% lower hydrocarbon (HC), 7.7% lower carbon monoxide (CO), 26% lower NOx at 80% load as compared to the unmodified diesel engine (CI mode).

Originality/value

The current research is an effort to study and evaluate the performance of CRDi engine in DF mode with diesel-H2 and BCPO-H2 fuel combinations with TRCC.

Details

Frontiers in Engineering and Built Environment, vol. 1 no. 1
Type: Research Article
ISSN: 2634-2499

Keywords

Open Access
Article
Publication date: 29 June 2021

C. Ahamed Saleel, Saad Ayed Alshahrani, Asif Afzal, Maughal Ahmed Ali Baig, Sarfaraz Kamangar and T.M. Yunus Khan

Joule heating effect is a pervasive phenomenon in electro-osmotic flow because of the applied electric field and fluid electrical resistivity across the microchannels. Its effect…

736

Abstract

Purpose

Joule heating effect is a pervasive phenomenon in electro-osmotic flow because of the applied electric field and fluid electrical resistivity across the microchannels. Its effect in electro-osmotic flow field is an important mechanism to control the flow inside the microchannels and it includes numerous applications.

Design/methodology/approach

This research article details the numerical investigation on alterations in the profile of stream wise velocity of simple Couette-electroosmotic flow and pressure driven electro-osmotic Couette flow by the dynamic viscosity variations happened due to the Joule heating effect throughout the dielectric fluid usually observed in various microfluidic devices.

Findings

The advantages of the Joule heating effect are not only to control the velocity in microchannels but also to act as an active method to enhance the mixing efficiency. The results of numerical investigations reveal that the thermal field due to Joule heating effect causes considerable variation of dynamic viscosity across the microchannel to initiate a shear flow when EDL (Electrical Double Layer) thickness is increased and is being varied across the channel.

Originality/value

This research work suggest how joule heating can be used as en effective mechanism for flow control in microfluidic devices.

Details

Frontiers in Engineering and Built Environment, vol. 1 no. 2
Type: Research Article
ISSN: 2634-2499

Keywords

Article
Publication date: 7 July 2020

Ahamed Saleel C., Asif Afzal, Irfan Anjum Badruddin, T.M. Yunus Khan, Sarfaraz Kamangar, Mostafa Abdelmohimen, Manzoore Elahi M. Soudagar and H. Fayaz

The characteristics of fluid motions in micro-channel are strong fluid-wall surface interactions, high surface to volume ratio, extremely low Reynolds number laminar flow, surface…

Abstract

Purpose

The characteristics of fluid motions in micro-channel are strong fluid-wall surface interactions, high surface to volume ratio, extremely low Reynolds number laminar flow, surface roughness and wall surface or zeta potential. Due to zeta potential, an electrical double layer (EDL) is formed in the vicinity of the wall surface, namely, the stern layer (layer of immobile ions) and diffuse layer (layer of mobile ions). Hence, its competent designs demand more efficient micro-scale mixing mechanisms. This paper aims to therefore carry out numerical investigations of electro osmotic flow and mixing in a constricted microchannel by modifying the existing immersed boundary method.

Design/methodology/approach

The numerical solution of electro-osmotic flow is obtained by linking Navier–Stokes equation with Poisson and Nernst–Planck equation for electric field and transportation of ion, respectively. Fluids with different concentrations enter the microchannel and its mixing along its way is simulated by solving the governing equation specified for the concentration field. Both the electro-osmotic effects and channel constriction constitute a hybrid mixing technique, a combination of passive and active methods. In microchannels, the chief factors affecting the mixing efficiency were studied efficiently from results obtained numerically.

Findings

The results indicate that the mixing efficiency is influenced with a change in zeta potential (ζ), number of triangular obstacles, EDL thickness (λ). Mixing efficiency decreases with an increment in external electric field strength (Ex), Peclet number (Pe) and Reynolds number (Re). Mixing efficiency is increased from 28.2 to 50.2% with an increase in the number of triangular obstacles from 1 to 5. As the value of Re and Pe is decreased, the overall percentage increase in the mixing efficiency is 56.4% for the case of a mixing micro-channel constricted with five triangular obstacles. It is also vivid that as the EDL overlaps in the micro-channel, the mixing efficiency is 52.7% for the given zeta potential, Re and Pe values. The findings of this study may be useful in biomedical, biotechnological, drug delivery applications, cooling of microchips and deoxyribonucleic acid hybridization.

Originality/value

The process of mixing in microchannels is widely studied due to its application in various microfluidic devices like micro electromechanical systems and lab-on-a-chip devices. Hence, its competent designs demand more efficient micro-scale mixing mechanisms. The present study carries out numerical investigations by modifying the existing immersed boundary method, on pressure-driven electro osmotic flow and mixing in a constricted microchannel using the varied number of triangular obstacles by using a modified immersed boundary method. In microchannels, the theory of EDL combined with pressure-driven flow elucidates the electro-osmotic flow.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 31 no. 3
Type: Research Article
ISSN: 0961-5539

Keywords

Open Access
Article
Publication date: 1 July 2021

Sarfaraz Kamangar, N. Ameer Ahamad, N. Nik-Ghazali, Ali E. Anqi, Ali Algahtani, C. Ahamed Saleel, Syed Javed, Vineet Tirth and T.M. Yunus Khan

Coronary artery disease (CAD) is reported as one of the most common sources of death all over the world. The presence of stenosis (plaque) in the coronary arteries results in the…

Abstract

Purpose

Coronary artery disease (CAD) is reported as one of the most common sources of death all over the world. The presence of stenosis (plaque) in the coronary arteries results in the restriction of blood supply, leading to myocardial infarction. The current study investigates the influence of multi stenosis on hemodynamic properties in a patient-specific left coronary artery.

Design/methodology/approach

A three-dimensional model of the patient-specific left coronary artery was reconstructed based on computed tomography (CT) scan images using MIMICS-20 software. The diseased model of the left coronary artery was investigated, having the narrowing of 90% and 70% of area stenosis (AS) at the left anterior descending (LAD) and left circumflex (LCX), respectively.

Findings

The results indicate that the upstream region of stenosis experiences very high pressure for 90% AS during the systolic period of the cardiac cycle. The pressure drops maximum as the flow travels into the stenotic zone, and the high flow velocities were observed across the 90% AS. The higher wall shear stresses occur at the stenosis region, and it increases with the increase in the flow rate. It is found that the maximum wall shear stress across 90% AS is at the highest risk for rupture. A recirculation region immediately after the stenosis results in the further development of stenosis.

Originality/value

The current study provides evidence that there is a strong effect of multi-stenosis on the blood flow in the left coronary artery.

Details

Frontiers in Engineering and Built Environment, vol. 1 no. 1
Type: Research Article
ISSN: 2634-2499

Keywords

Article
Publication date: 6 November 2017

Irfan Anjum Badruddin, Azeem Khan, Mohd Yamani Idna Idris, N. Nik-Ghaali, Salman Ahmed N.J. and Abdullah A.A.A. Al-Rashed

The purpose of this paper is to highlight the advantages of a simplified algorithm to solve the problem of heat and mass transfer in porous medium by reducing the number of…

Abstract

Purpose

The purpose of this paper is to highlight the advantages of a simplified algorithm to solve the problem of heat and mass transfer in porous medium by reducing the number of partial differential equations from four to three.

Design/methodology/approach

The approach of the present paper is to develop a simplified algorithm to reduce the number of equations involved in conjugate heat transfer in porous medium.

Findings

Developed algorithm/method has many advantages over conventional method of solution for conjugate heat transfer in porous medium.

Research limitations/implications

The current work is applicable to conjugate heat transfer problem.

Practical implications

The developed algorithm is useful in reducing the number of equations to be solved, thus reducing the computational resources required.

Originality/value

Development of simplified algorithm and comparison with conventional method.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 27 no. 11
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 4 June 2024

Adebowale Martins Obalalu, Adil Darvesh, Lateefat Aselebe, Sulyman Olakunle Salawu and Kazeem Issa

The primary focus of this study is to tackle a critical industry issue concerning energy inefficiency. This is achieved through an investigation into enhancing heat transfer in…

Abstract

Purpose

The primary focus of this study is to tackle a critical industry issue concerning energy inefficiency. This is achieved through an investigation into enhancing heat transfer in solar radiation phenomena on a curved surface. The problem formulation of governing equations includes the combined effects of thermal relaxation, Newtonian heating, radiation mechanism, and Darcy-Forchheimer to enhance the uniqueness of the model. This research employs the Cattaneo–Christov heat theory model to investigate the thermal flux via utilizing the above-mentioned phenomenon with a purpose of advancing thermal technology. A mixture of silicon dioxide (SiO_2)\ and Molybdenum disulfide (MoS_2) is considered for the nanoparticle’s thermal propagation in base solvent propylene glycol. The simulation of the modeled equations is solved using the Shifted Legendre collocation scheme (SLCS). The findings show that, the solar radiation effects boosted the heating performance of the hybrid nanofluid. Furthermore, the heat transmission progress increases against the curvature and thermal relaxation parameter.

Design/methodology/approach

Shifted Legendre collocation scheme (SLCS) is utilized to solve the simulation of the modeled equations.

Findings

The findings show that, the solar radiation effects boosted the heating performance of the hybrid nanofluid. The heat transmission progress increase against the curvature and thermal relaxation parameter.

Originality/value

This research employs the Cattaneo–Christov heat theory model to investigate the thermal flux via utilizing the above-mentioned phenomenon with a purpose of advancing thermal technology.

Details

Multidiscipline Modeling in Materials and Structures, vol. 20 no. 4
Type: Research Article
ISSN: 1573-6105

Keywords

Article
Publication date: 14 December 2023

Swapnil Narayan Rajmane and Shaligram Tiwari

This study aims to perform three-dimensional numerical computations for blood flow through a double stenosed carotid artery. Pulsatile flow with Womersley number (Wo) of 4.65 and…

Abstract

Purpose

This study aims to perform three-dimensional numerical computations for blood flow through a double stenosed carotid artery. Pulsatile flow with Womersley number (Wo) of 4.65 and Reynolds number (Re) of 425, based on the diameter of normal artery and average velocity of inlet pulse, was considered.

Design/methodology/approach

Finite volume method based ANSYS Fluent 20.1 was used for solving the governing equations of three-dimensional, laminar, incompressible and non-Newtonian blood flow. A high-quality grid with sufficient refinement was generated using ICEM CFD 20.1. The time-averaged flow field was captured to investigate the effect of severity and eccentricity on the lumen flow characteristics.

Findings

The results show that an increase in interspacing between blockages brings shear layer instability within the region between two blockages. The velocity profile and wall shear stress distribution are found to be majorly influenced by eccentricity. On the other hand, their peak magnitude is found to be primarily influenced by severity. Results have also demonstrated that the presence of eccentricity in stenosis would assist in flow development.

Originality/value

Variation in severity and interspacing was considered with a provision of eccentricity equal to 10% of diameter. Eccentricity refers to the offset between the centreline of stenosis and the centreline of normal artery. For the two blockages, severity values of 40% and 60% based on diameter reduction were permuted, giving rise to four combinations. For each combination, three values of interspacing in the multiples of normal artery diameter (D), viz. 4D, 6D and 8D were considered.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 34 no. 3
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 19 December 2018

Ameer Ahamad Nandalur, Sarfaraz Kamangar and Irfan Anjum Badruddin

The purpose of this study was to analyze the heat transfer in a square porous cavity that has a solid block placed at its center. The prime focus of this study is to investigate…

Abstract

Purpose

The purpose of this study was to analyze the heat transfer in a square porous cavity that has a solid block placed at its center. The prime focus of this study is to investigate the effect of size of the square solid block and other physical parameters on the heat transfer rate from the hot surface into the porous medium. The left vertical surface of cavity is maintained at a hot temperature and the right vertical surface at a cool temperature, Tc. The finite element method is used to simplify the governing equations and is solved iteratively. It is noted that the size of the solid block plays a vital role in dictating the heat transfer from the hot surface to porous medium.

Design/methodology/approach

The current work is based on finite element formulation of a square porous cavity that has a solid square block placed at its center. Governing equations were solved iteratively.

Findings

The size of the solid block has a pronounced effect on the heat transfer behavior inside the porous cavity.

Originality/value

This study highlights the heat transfer due to a conducting square solid block at mid of porous cavity.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 29 no. 2
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 6 October 2023

Cleiton Lazaro Fazolo De Assis and Cleber Augusto Rampazo

This paper aims to evaluate the mechanical behaviour of polycarbonate/acrylonitrile butadiene styrene (PC/ABS) filaments for fusion filament fabrication (FFF). PC/ABS have emerged…

Abstract

Purpose

This paper aims to evaluate the mechanical behaviour of polycarbonate/acrylonitrile butadiene styrene (PC/ABS) filaments for fusion filament fabrication (FFF). PC/ABS have emerged as a promising material for FFF due to their excellent mechanical properties. However, the optimal processing conditions and the effect of the blending ratio on the mechanical properties of the resulting workpieces are still unclear.

Design/methodology/approach

A statistical factorial matrix was designed, including infill pattern, printing speed, nozzle size, layer height and printing temperature as factors (with three levels). A total of 810 workpieces were printed using PC/ABS blends filament with the FFF. The workpieces’ finishing and mass were evaluated. Tensile tests were performed. Analysis of variance was performed to determine the main effects of the processing conditions on the mechanical properties.

Findings

The results showed that the PC/ABS (70/30) exhibited higher tensile. Tensile rupture corresponded to 30% of the tensile strength. The infill pattern showed the highest contribution to the responses. The concentric pattern showed higher tensile strength. Tensile strength and mass ratio demonstrated the influence of mass on tensile strength. The influence of printing parameters on deformation depended on the blend proportions. Higher printing speed and lower layer height provided better quality workpieces.

Originality/value

This study has implications for the design and manufacturing of three-dimensional printed parts using PC/ABS filaments. An extensive experimental matrix was applied, aiming at a complete understanding of mechanical behavior, considering the main printing parameters and combinations not explored by literature.

Details

Rapid Prototyping Journal, vol. 30 no. 2
Type: Research Article
ISSN: 1355-2546

Keywords

Article
Publication date: 11 February 2021

Parvez Alam, Suprava Jena, Irfan Anjum Badruddin, Tatagar Mohammad Yunus Khan and Sarfaraz Kamangar

This paper aims to study the attenuation and dispersion phenomena of shear waves in anelastic and elastic porous strips. Numerical investigations are performed for the phase and…

Abstract

Purpose

This paper aims to study the attenuation and dispersion phenomena of shear waves in anelastic and elastic porous strips. Numerical investigations are performed for the phase and damped velocity profiles of the wave. For numerical computation purposes, water-saturated limestone and kerosene oil saturated sandstone for the first and second porous strips, respectively. Some other peculiarities have been observed and discussed.

Design/methodology/approach

Dispersion and attenuation characteristic of the shear wave propagations have been studied in an inhomogeneous poro-anelastic strip of finite thickness, which is clamped between an inhomogeneous poroelastic strip of finite thickness and an elastic half-space. Both the strips are initially stressed and the half-space is self-weighted. Analytical methods are used to calculate the interior deformations of the model with the involvement of special functions. The determination of the frequency equation, which includes the Bessel’s and Whittaker functions, has been obtained using the prescribed boundary conditions.

Findings

Impacts of attenuation coefficient, dissipation factor, inhomogeneities, initial stresses, Biot’s gravity, porosity and thickness ratio parameters on the velocity profile of the wave have been demonstrated through the graphical visuals. These parameters are playing an important role and working as a catalyst in affecting the propagation behaviour of the wave.

Originality/value

Inclusion of the concept of doubly layered initially stressed inhomogeneous porous structure of elastic and anelastic medium bedded over a self-weighted half-space medium brings a novelty to the existing literature related to the study of shear wave. It may be helpful to geologists, seismologists and structural engineers in the development of theoretical and practical studies.

Details

Engineering Computations, vol. 38 no. 7
Type: Research Article
ISSN: 0264-4401

Keywords

1 – 10 of 345