Search results

The purpose of this study was expected to simultaneously monitor the surface roughness of each solidified layer, the surface roughness of the metal powder, the outline of the solidified layer, and the height difference between the solidified layer and the metal powder.

In the proposed approach, color images with red, green and blue fringes are used to measure the shape of the built object using a three-step phase-shift algorithm and phase-unwrapping method. In addition, the surface roughness is extracted from the speckle information in the captured image using a predetermined autocorrelation function.

The feasibility and accuracy of the proposed system were validated by comparing it with a commercial system for an identical set of samples fabricated by a selective laser melting process. The maximum and minimum errors between the two systems are approximately 24% and 0.8%, respectively.

In the additive manufacturing field, the authors are the first to use fringe detection technology to simultaneously measure the profile of the printed layer and its surface roughness.

In this study, experimental studies were carried out using different process parameters of the soft pneumatic gripper (SPG) fabricated by the fused deposition modeling method. In the experimental studies, the surface quality of the gripper was examined by determining four different levels and factors. The experiment was designed to estimate the surface roughness of the SPG.

The methodology consists of an experimental phase in which the SPG is fabricated and the surface roughness is measured. Thermoplastic polyurethane (TPU) flex filament material was used in the fabrication of SPG. The control factors used in the Taguchi L16 vertical array experimental design and their level values were determined. Analysis of variance (ANOVA) was performed to observe the effect of printing parameters on the surface quality. Finally, regression analysis was applied to mathematically model the surface roughness values obtained from the experimental measurements.

Based on the Taguchi signal-to-noise ratio and ANOVA, layer height is the most influential parameter for surface roughness. The best surface quality value was obtained with a surface roughness value of 18.752 µm using the combination of 100 µm layer height, 2 mm wall thickness, 200 °C nozzle temperature and 120 mm/s printing speed. The developed model predicted the surface roughness of SPG with 95% confidence intervals.

It is essential to examine the surface quality of parts fabricated in additive manufacturing using different variables. In the literature, surface roughness has been examined using different factors and levels. However, the surface roughness of a soft gripper fabricated with TPU material has not been examined previously. The surface quality of parts fabricated using flexible materials is very important.

Modeling helps to determine how structural parameters of fabric affect the surface of a fabric and also identify the way they influence fabric properties. Moreover, it helps to estimate and evaluate without the complexity and time-consuming experimental procedures. The purpose of this study is to develop and select the best regression model equations for the prediction and evaluation of surface roughness of plain-woven fabrics.

In this study, a linear and quadratic regression model was developed for the prediction and evaluation of surface roughness of plain-woven fabrics, and the capability in accuracy and reliability of the two-model equation was determined by the root mean square error (RMSE). The Design-Expert AE11 software was used for developing the two model equations and analysis of variance “ANOVA.” The count and density were used for developing linear model equation one “SMD1” as well as for quadratic model equation two “SMD2.”

From results and findings, the effects of count and density and their interactions on the roughness of plain-woven fabric were found statistically significant for both linear and quadratic models at a confidence interval of 95%. The count has a positive correlation with surface roughness, while density has a negative correlation. The correlations revealed that models were strongly correlated at a confidence interval of 95% with adjusted R² of 0.8483 and R² of 0.9079, respectively. The RMSE values of the quadratic model equation and linear model equation were 0.1596 and 0.0747, respectively.

Thus, the quadratic model equation has better capability accuracy and reliability in predictions and evaluations of surface roughness than a linear model. These models can be used to select a suitable fabric for various end applications, and it was also used for tests and predicts surface roughness of plain-woven fabrics. The regression model helps to reduce the gap between the subjective and objective surface roughness measurement methods.

The purpose of this paper is to investigate the performance of four cutting oils, two different vegetable‐based cutting fluids developed from refined sunflower oil and two commercial types (semi‐synthetic and mineral), for surface roughness during drilling of AISI 304 austenitic stainless steel with HSSE tool.

L₉ (3³) orthogonal array was used for the experiment plan. Spindle speed, feed rate and drilling depth were considered as machining parameters.

Results were evaluated statistically. Mathematical models based on cutting parameters were obtained from regression analyses to predict surface roughness. ANOVA was used to determine the effect of the cutting parameters on the surface roughness. The performance results were found to be better for vegetable‐based cutting oils than that of commercial ones.

The paper reports on the use of refined sunflower oil in drilling stainless steel.

This paper aims to study the comparison between a response surface methodology (RSM) and artificial neural network (ANN) in the modelling and prediction of surface roughness during endmilling of glass-fibre-reinforced polymer composites.

Aiming to achieve this goal, several milling experiments were performed with polycrystalline diamond inserts at different machining parameters, namely, feed rate, cutting speed, depth of cut and fibre orientation angle. Mathematical model is created using central composite face-centred second-order in RSM and the adequacy of the model was verified using analysis of variance. ANN model is created using the back propagation algorithm.

With regard to the machining test, it was observed that feed rate is the dominant parameter that affects the surface roughness, followed by the fibre orientation. The comparison results show that models provide accurate prediction of surface roughness in which ANN performs better than RSM.

The data predicted from ANN are very nearer to experimental results compared to RSM; therefore, this ANN model can be used to determine the surface roughness for various fibre-reinforced polymer composites and also for various machining parameters.

The mechanical properties and surface finish of functional parts are important consideration in rapid prototyping, and the selection of proper parameters is essential to improve manufacturing solutions. The purpose of this paper is to describe how parts manufactured by fused deposition modelling (FDM), with different part orientations and raster angles, were examined experimentally and evaluated to achieve the desired properties of the parts while shortening the manufacturing times due to maintenance costs.

For this purpose, five different raster angles (0°, 30°, 45°, 60° and 90°) for three part orientations (horizontal, vertical and perpendicular) have been manufactured by the FDM method and tested for surface roughness, tensile strength and flexural strength. Also, behaviour of the mechanical properties was clarified with scanning electron microscopy images of fracture surfaces.

The research results suggest that the orientation has a more significant influence than the raster angle on the surface roughness and mechanical behaviour of the resulting fused deposition part. The results indicate that there is close relationship between the surface roughness and the mechanical properties.

The results of this paper are useful in defining the most appropriate raster angle and part orientation in minimum production cost for FDM components on the basis of their expected in-service loading.

This paper aims to propose a non-contact method using machine vision for measuring the surface roughness of a rotating workpiece at speeds of up to 4,000 rpm.

A commercial digital single-lens-reflex camera with high shutter speed and backlight was used to capture a silhouette of the rotating workpiece profile. The roughness profile was extracted at sub-pixel accuracy from the captured images using the moment invariant method of edge detection. The average (Ra), root-mean square (Rq) and peak-to-valley (Rt) roughness parameters were measured for ten different specimens at spindle speeds of up to 4,000 rpm. The roughness values measured using the proposed machine vision system were verified using the stylus profilometer.

The roughness values measured using the proposed method show high correlation (up to 0.997 for Ra) with those determined using the profilometer. The mean differences in Ra, Rq and Rt between the two methods were only 4.66, 3.29 and 3.70 per cent, respectively.

The proposed method has significant potential for application in the in-process roughness measurement and tool condition monitoring from workpiece profile signature during turning, thus, obviating the need to stop the machine.

The machine vision method combined with sub-pixel edge detection has not been applied to measure the roughness of a rotating workpiece.

This paper aims to report on the findings of an investigation to compare three different three-dimensional printing (3DP) or additive manufacturing technologies [i.e. fused deposition modeling (FDM), stereolithography (SLA) and material jetting (MJ)] and four different equipment (FDM, SLA, MJP 2600 and Object 260) in terms of their dimensional process capability (dimensional accuracy and surface roughness). It provides a comprehensive and comparative understanding about the level of attainable dimensional accuracy, repeatability and surface roughness of commonly used 3DP technologies. It is expected that these findings will help other researchers and industrialists in choosing the right technology and equipment for a given 3DP application.

A benchmark model of 5 × 5 cm with several common and challenging features, such as around protrusion and hole, flat surface, micro-scale ribs and micro-scale long channels was designed and printed repeatedly using four different equipment of three different 3DP technologies. The dimensional accuracy of the printed models was measured using non-contact digital measurement methods. The surface roughness was evaluated using a digital profilometer. Finally, the surface quality and edge sharpness were evaluated under a reflected light ZEISS microscope with a 50× magnification objective.

The results show that FDM technology with the used equipment results in a rough surface and loose dimensional accuracy. The SLA printer produced a smoother surface, but resulted in the distortion of thin features (<1 mm). MJ printers, on the other hand, produced comparable surface roughness and dimensional accuracy. However, ProJet MJP 3600 produced sharper edges when compared to the Objet 260 that produced round edges.

This paper, for the first time, provides a comprehensive comparison of three different commonly used 3DP technologies in terms of their dimensional capability and surface roughness without farther post-processing. Thus, it offers a reliable guideline for design consideration and printer selection based on the target application.

The objectives of this study were to determine: the type of coating that minimized pipe surface roughness and how the choice of metrological instrument could influence pipe surface roughness data. The internal surface of pipe was coated with either phenolic, modified novalac, epoxy, or nylon material. Roughness of coated pipe was assessed with two linear surface profilers, a Dektak³ST^® and a Hommel T1000, and a Dimension 3000^® atomic force microscope (AFM). Arithmetic roughness (R_a), root mean square roughness (R_q), and mean peak‐to‐valley height (R_ZD), were statistically analyzed. The ability of R_ZD to focus on the extremes of height and depth on the surface made it a significant parameter for detecting features that would affect fluid flow in pipes.

This paper aims to investigate the dimensional accuracy consisting of thickness, grip section width, full length, circularity, cylindricity and surface finish of printed polyurethane dog-bone samples based on American Society for Testing and Materials D638 type V standard, which were optimally printed by fused deposition modelling (FDM).

The experimental approach focuses on determining main effects of printing parameters, including nozzle temperature, infill percentage, print speed and layer height on dimensional error and surface finish of the printed samples, followed by the confirmation tests to warrant the reproducibility of experimental results.

This study shows that layer height has the most significant impact on dimensional accuracy and surface finish of printed samples compared to other printing parameters, whereas infill density has no significant effect on all sample dimensions.

This paper presents a comprehensive study relating to various dimensional accuracies in terms of full length, grip section width, thickness, circularity, cylindricity and surface finish of dog-bone samples printed by FDM to improve the printability and processibility via additive manufacturing.