Search results

Structural stress and strain in the key components of aircraft structure is important for structural health monitoring and strength assessment. However, the measure of dynamic strain is often difficult to implement because of the complex test equipment and inconvenient measure points, especially in flight test. This study aims to propose an algorithm of dynamic strain estimation using the acceleration response in time domain to simplify the measure of dynamic strain.

The relationship between the strain and acceleration response is established through the sinusoidal response or modal analysis, which is insensitive to the excitation position and form. A band-pass filter is used to obtain the modal acceleration response, and a filter frequency band selection method is proposed. Then, the dynamic strain at the concerned points can be estimated based on the modal superposition principle.

Simulation and experiment are implemented to validate the applicability and effectiveness of the strain estimation method. The estimated strain results agree well with numerical simulation as well as the experimental results. The simplicity and accuracy of the strain estimation method show practicability for dynamic strength and fatigue analysis in engineering applications.

An algorithm of dynamic strain estimation using the acceleration response in time domain is developed. A band-pass filter is used to obtain the modal acceleration response, and a filter frequency band selection method is proposed. The dynamic strain at the concerned points can be estimated based on the modal superposition principle.

Gives a bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore aims to give the reader an encyclopaedic view on the subject. The bibliography at the end of the paper contains 2,025 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1992‐1995.

The purpose of this study is to review the existing fatigue and vibration-based structural health monitoring techniques and highlight the advantages of combining both approaches.

Fatigue monitoring requires a fatigue model of the material, the stresses at specific points of the structure, a cycle counting technique and a fatigue damage criterion. Firstly, this paper reviews existing structural health monitoring (SHM) techniques, addresses their principal classifications and presents the main characteristics of each technique, with a particular emphasis on modal-based methodologies. Automated modal analysis, damage detection and localisation techniques are also reviewed. Fatigue monitoring is an SHM technique which evaluate the structural fatigue damage in real time. Stress estimation techniques and damage accumulation models based on the S-N field and the Miner rule are also reviewed in this paper.

A vast amount of research has been carried out in the field of SHM. The literature about fatigue calculation, fatigue testing, fatigue modelling and remaining fatigue life is also extensive. However, the number of publications related to monitor the fatigue process is scarce. A methodology to perform real-time structural fatigue monitoring, in both time and frequency domains, is presented.

Fatigue monitoring can be combined (applied simultaneously) with other vibration-based SHM techniques, which might significantly increase the reliability of the monitoring techniques.

The purpose of this paper is to contribute to the solution of the fatigue damage problem of reinforced concrete frames in bending.

The problem of fatigue damage is formulated based on the rheological–dynamical analogy, including a scalar damage variable to address the reduction of stiffness in strain softening. The modal analysis is used by the finite element method for the determination of modal parameters and resonance stability of the selected frame cross-section. The objectivity of the presented method is verified by numerical examples, predicting the ductility in bending of the frame whose basic mechanical properties were obtained by non-destructive testing systems.

The modal analysis in the frame of the finite element method is suitable for the determination of modal parameters and resonance stability of the selected frame cross-section. It is recommended that the modulus of elasticity be determined by non-destructive methods, e.g. from the acoustic response.

The paper presents a novel method of solving the ductility in bending taking into account both the creep coefficient and the aging coefficient. The rheological-dynamical analogy (RDA) method uses the resonant method to find material properties. The characterization of the structural damping via the damping ratio is original and effective.

The purpose of this paper is to further validate a wireless sensor system developed at Clarkson University for structural monitoring of highway bridges. The particular bridge monitored employs a fiber reinforced polymer (FRP) panel system which is fairly innovative in the field of civil engineering design. The superstructure was monitored on two separate occasions to determine a change in structural response and see how the structural system performs over time.

A series of wireless sensor units was deployed at various locations of the steel superstructure, to measure both the modal response from acceleration measurements as well as quasi‐static and dynamic strain response. Ambient and forced loading conditions were applied to measure the response. Data results were compared over two separate periods approximately nine months apart.

The first eight mode shapes were produced from output‐only system identification providing natural frequencies ranging from approximately 6 to 42 Hz. The strain response was monitored over two different testing periods to measure various performance characteristics. Neutral axis, distribution factor, impact factor and end fixity were determined. Results appeared to be different over the two testing periods. They indicate that the load rating of the superstructure decreased over the nine month period, possibly due to deterioration of the materials or composite action.

The results from the two testing periods indicate that further testing needs to be completed to validate the change in response. It is difficult to say with certainty that the significant change in response is due to bridge deterioration and not other factors such as temperature effects on load rating. The sensor system, however, proved to provide high quality data and responses indicating its successful deployment for load testing and monitoring of highway infrastructure.

The paper provides a depiction of the change in structural behavior of a bridge superstructure using a wireless sensor system. The wireless system provided high‐rate data transmission in real time. Load testing at two different points in time, eight months apart, showed a significant change in bridge behavior. The paper provides a practical and actual physical load test and rating during these two periods for quantifiable change in response. It is shown that the wireless system is capable of infrastructure monitoring and that possible deterioration is expected with this particular bridge design. Additionally, the load testing occurred during different seasons, which could create cause for temperature effects in load rating. This can provide a basis for future performance monitoring techniques and structural health monitoring.

This method will become a new development trend in subgrade structure design for high speed railways.

This paper summarizes the structural types and design methods of subgrade bed for high speed railways in China, Japan, France, Germany, the United States and other countries based on the study and analysis of existing literature and combined with the research results and practices of high speed railway subgrade engineering at home and abroad.

It is found that in foreign countries, the layered reinforced structure is generally adopted for the subgrade bed of high speed railways, and the unified double-layer or multi-layer structure is adopted for the surface layer of subgrade bed, while the simple structure is adopted in China; in foreign countries, different inspection parameters are adopted to evaluate the compaction state of fillers according to their respective understanding and practice, while in China, compaction coefficient, subsoil coefficient and dynamic deformation modulus are adopted for such evaluation; in foreign countries, the subgrade top deformation control method, the subgrade bottom deformation control method, the subsurface fill strength control method are mainly adopted in subgrade bed structure design of high speed railways, while in China, dynamic deformation control of subgrade surface and dynamic strain control of subgrade bed bottom layer is adopted in the design. However, the cumulative deformation of subgrade caused by train cyclic vibration load is not considered in the existing design methods.

This paper introduces a new subgrade structure design method based on whole-process dynamics analysis that meets subgrade functional requirements and is established on the basis of the existing research at home and abroad on prediction methods for cumulative deformation of subgrade soil.

The purpose of this article is to suggest that Fraby‐Perot optic sensor is a practical measurement gage to monitor the strain of great structures such as railway bridges.

A remote strain monitoring system based on F‐P optic fiber and virtual instrument is designed to monitor the strains of a railway bridge.

The application results show that the Fraby‐Perot optical fiber sensors can accurately measure strain and they are suitable for the long‐term and automatic monitoring. In addition, the system has several advantages over conventional structural instruments including fast response, ability of both static and dynamic monitoring, absolute measurement, immunity to interferences such as lightning strikes, electromagnetic noise and radio frequency, low attenuation of light signals in long fiber optic cables.

Health monitoring of structures is getting more and more recognition all over the world because it can minimize the cost of reparation and maintenance and ensure the safety of structures. A strain monitoring system based on F‐P optic fiber sensor was developed according to the health monitoring requirements of Wuhu Yangtze River Railway Bridge, which is the first cable‐stayed bridge with a maximum span of 312 m carrying both railway and highway traffic in China. It has run stably in the monitoring field more than two years and fulfilled the monitoring requirement very well. Now the system has been transplanted successfully to the Zhengzhou Yellow Railway Bridge for strain monitoring. So the work can be referenced by other similar health monitoring projects.

Long‐term, real‐time monitoring of strain using FP fiber optic sensors in railway bridge is an innovation. A remote strain data acquisition and real‐time processing are another character of the system. The work studied can be referenced by other structures monitoring, such as tunnel, concrete bridges, concrete and earth dams.

This paper aims to analyze the bearing characteristics of the high speed train window glass under aerodynamic load effects.

In order to obtain the dynamic strain response of passenger compartment window glass during high-speed train crossing the tunnel, taking the passenger compartment window glass of the CRH3 high speed train on Wuhan–Guangzhou High Speed Railway as the research object, this study tests the strain dynamic response and maximum principal stress of the high speed train passing through the tunnel entrance and exit, the tunnel and tunnel groups as well as trains meeting in the tunnel at an average speed of 300 km·h-1.

The results show that while crossing the tunnel, the passenger compartment window glass of high speed train is subjected to the alternating action of positive and negative air pressures, which shows the typical mechanic characteristics of the alternating fatigue stress of positive-negative transient strain. The maximum principal stress of passenger compartment window glass for high speed train caused by tunnel aerodynamic effects does not exceed 5 MPa, and the maximum value occurs at the corresponding time of crossing the tunnel groups. The high speed train window glass bears medium and low strain rates under the action of tunnel aerodynamic effects, while the maximum strain rate occurs at the meeting moment when the window glass meets the train head approaching from the opposite side in the tunnel. The shear modulus of laminated glass PVB film that makes up high speed train window glass is sensitive to the temperature and action time. The dynamically equivalent thickness and stiffness of the laminated glass and the dynamic bearing capacity of the window glass decrease with the increase of the action time under tunnel aerodynamic pressure. Thus, the influence of the loading action time and fatigue under tunnel aerodynamic effects on the glass strength should be considered in the design for the bearing performance of high speed train window glass.

The research results provide data support for the analysis of mechanical characteristics, damage mechanism, strength design and structural optimization of high speed train glass.

This paper describes a recent collaborative project involving the development of a multiplexed fibre Bragg grating (FBG) sensor system for structural integrity monitoring.

The system is described and field trials on both conventional and novel composite bridges are discussed. A FBG sensor‐based structural monitoring system was developed, based on a fluorescent fibre as the optical source. It used a tuneable, fibre‐coupled, Fabry‐Perot filter, actuated by piezoelectric transducers and operated over the bandwidth of the source at up to 250 scans/second. Light from the source was filtered and reflected back from the Bragg gratings, through optical couplers, to eight photodiode detectors. These detected the resulting time‐domain spectra of the sensors in each of the serially connected sensor arrays. The system was tested at City University and then subjected to trials on the Mjosund road bridge in Norway and on West Mill bridge in Oxfordshire, UK, which is the first bridge to be fabricated from a new type of composite material.

During the Norwegian trials the system was arranged with four or five FBG sensors per channel giving a total of 32 measurement points with eight parallel channels. Twelve conventional foil strain gauges and a number of thermocouples were also installed. Different static and dynamic loads were applied over a period of 18 months and the results showed that the thermally compensated strain data obtained optically matched those from the resistive gauges to within <5 με. During the construction stage of the Oxfordshire bridge, sections of the decking and longitudinal composite support beams were instrumented with 40 FBG sensors with temperature compensation, placed at pre‐selected sites of maximum strain. These exhibited a resolution of ±5 με and an operating range of over ±2,000 με.

This research has shown that multiplexed, multi‐point FBG sensor systems can accurately and reliably monitor both static and dynamic strains in large structures over a range of temperatures and for extended periods of time.

A bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view is given. The bibliography at the end of the paper contains 1,726 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1996‐1999.