Search results

AA2014 is a copper-based alloy and is typically used for production of complex machined components, given its better machinability. The purpose of this paper was to study the effects of variation in weight percentage of ceramic Al₂O₃ particulates during electrical discharge machining (EDM) of stir cast AA2014 composites. Scanning electron microscopy (SEM) examination was carried out to study characteristics of EDMed surface of Al₂O₃/AA2014 composites.

The effect of machining parameters on performance measures during sinker EDM of stir cast Al₂O₃/AA2014 composites was examined by “one factor at a time” (OFAT) method. The stir cast samples were obtained by using three levels of weight percentage of Al₂O₃ particulates, i.e. 0 Wt.%, 10 Wt.% and 20 Wt.% with density 1.87 g/cc, 2.35 g/cc and 2.98 g/cc respectively. Machining parameters varied were peak current (1-30 amp), discharge voltage (30-100 V), pulse on time (15-300 µs) and pulse off time (15-450 µs) to study their influence on material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR).

MRR and SR decreased with an increase in weight percentage of ceramic Al₂O₃ particulates at the expense of TWR. This was attributed to increased microhardness for reinforced stir cast composites. However, microhardness of EDMed samples at fixed values of machining parameters, i.e. 9 amp current, 60 V voltage, 90 µs pulse off time and 90 µs pulse on time reduced by 58.34, 52.25 and 46.85 per cent for stir cast AA2014, 10 Wt.% Al₂O₃/AA2014 and 20 Wt.% Al₂O₃/AA2014, respectively. SEM and quantitative energy dispersive spectroscopy (EDS) analysis revealed ceramic Al₂O₃ particulate thermal spalling in 20 Wt.% Al₂O₃/AA2014 composite. This was because of increased particulate weight percentage leading to steep temperature gradients in between layers of base material and heat affected zone.

This work was an essential step to assess the machinability for material design of Al₂O₃ reinforced aluminium metal matrix composites (AMMCs). Experimental investigation on sinker EDM of high weight fraction of particulates in AA2014, i.e. 10 Wt.% Al₂O₃ and 20 Wt.% Al₂O₃, has not been reported in archival literature. The AMMCs were EDMed at variable peak currents, voltages, pulse on and pulse off times. The effects of process parameters on MRR, TWR and SR were analysed with comparisons made to show the effect of Al₂O₃ particulate contents.

This paper aims to extract the Cr from chrome containing leather waste (CCLW) in order to develop composite at optimum casting parameters using RSM technique. Chrome containing leather wastes (CCLW) is one of the significant cause of pollution that is exhaled by the leather industries. One of the technique to address the problem of pollution that is created by CCLW is to recycle it and produce some fruitful results from it. This will not only minimize the levels of harmful emissions to some extent but also give some befitting results.

The current work is all about exploring the ways by which CCLW could be used as a reinforcing material with aluminum. In this work, alumina has been used as a secondary reinforcement particle together with CCLW as with the help of stir casting process. The parameters of stir casting have been optimized by using “Response Surface Methodology.”

To maximize the hardness and tensile strength the values of optimal input casting parameters as found by the experimental results (response surface methodology) are as follows: the pre-heating temperature of collagen and alumina must be 166 °C and 300 °C, respectively, while the wt.% of collagen and alumina present in the matrix must be 2.45% and 5% sequentially 180 s of stirring time.

The hardness of the finally tested composite is 67.12 BHN (approx) which has been enhanced by 52.54% as compared to the base material. Tensile strength of composite also enhanced about 18% with respect to base material developed at the optimum combination of casting parameters.

The purpose of this article is to numerically investigate the effect of casting speed on the fluid flow, solidification and inclusion motion under the influence of electromagnetic stirring (EMS) in the bloom caster mold with bifurcated submerged entry nozzle (SEN).

The electromagnetic field obtained by solving Maxwell’s equation is coupled with the fluid flow, solidification and discrete phase model using the in-house user-defined functions. An enthalpy porosity approach and Lagrangian approach are applied for the solidification analysis and non-metallic inclusions motion tracking, respectively.

Investigation shows that the casting speed and EMS significantly affect the steel flow, solidification and inclusion behavior inside the mold. Investigations are being conducted into the complex interplay between the induced flow and the SEN’s inertial impinging jet. In low and medium casting speeds, the application of EMS significantly increases the inclusion removal rate. Inclusion removal is studied for its different size and density and further effect of EMS is also reported on cluster formation and distribution of inclusion in the domain.

The model may be used to optimize the process parameter (casting speed and EMS) to improve the casting quality of steel by removing the impurities.

The effect of casting speed on the solidification and inclusion behavior under the influence of time-varying EMS in bloom caster mold with bifurcated nozzle has not been investigated yet. The findings may assist the steelmakers in improving the casting quality.

The purpose of this paper is to develop a concept and design to cast Al alloys/metal matrix composites (MMCs) by continuous casting process. The various steps involved in the evolution of the design have been reported and discussed in this study.

On the basis of developed design concept, initial prototype design has been prepared in this study. The casting process's melt flow pattern was studied via computer simulation, and the resulting changes were implemented in the original design. The single-phase fluid flow pattern through bottom feeding technique is studied. The equipment was fabricated based on computer simulation and water modelling studies. Finally, validation was performed for the preparation of Al alloys/ MMCs after parameter optimisation. The results were observed in the optical metallography to confirm the alloying and Al MMC preparation.

The developed continuous casting process with bottom feeding technique for the addition of constituent particles shows more efficiency in comparison to the existing batch processes. The final manufactured setup demonstrates effective Al alloy/MMC production as the basis for final fabrication has been accomplished by both computer simulation and water model test. In addition, the microstructure exhibits homogeneous distribution, validating the reliability of the setup.

Integrating continuous casting with continuous reinforcement or master alloy addition is novel in this area. The constraints that batch production had that have been rectified will also lower the contemporary cost of production.

The purpose of this paper is to understand the effect of particle content, applied load and sliding speed on the tribological properties of A356-SiCP composites manufactured using a newly developed vacuum stir casting technique.

A356 alloy reinforced with 10, 15 and 20 vol% SiC particles was prepared by vacuum stir casting. Tribological tests were carried out on block-on-ring tribometer under dry sliding conditions, room temperature. Wear mechanism was investigated by scanning electron microscope and energy dispersion spectrum.

SiCP is homogeneously dispersed in the matrix. The increase in SiCP content decrease wear rate, but it leads to an increase in coefficient of friction. The wear rate increase and friction coefficient present different variation trends with increasing load. For A356-20%SiCP composite, when the load is less than 10 MPa, wear rate and friction coefficient under sliding speed of 400 rpm are lower than those of 200 rpm. Wear mechanism transition from abrasion, oxidation, delamination, adhesion to plastic flow as load and sliding speed increasing.

Results of this study will help guide the use of A356-SiCP in many automotive products such as brake rotors, brake pads, brake drums and pistons.

There are few paper studies the effect of particle content, applied load and sliding speed on the tribological properties of A356-SiCP composites. Aluminum matrix composites with uniform distribution of reinforcing particles were successfully prepared by using the newly developed vacuum stir casting technique.

This study aims to analyse the changes in mechanical and wear performance of aluminium alloy when yttrium oxide particles are incorporated. The microstructures are studied to analyse the change in the grain structures. Worn surfaces are observed via scanning electron microscope to study the wear mechanism in detail.

Stir casting is used to incorporate varying composition of yttrium particles, having an average particle size of 25 micrometer, in aluminium alloy 6063 matrix. Wear testing is carried out by DUCOM manufactured high temperature rotatory tribometer, and an indentation test is used for analysing the microhardness of the fabricated samples.

Microhardness of the material is increased with the increasing content of particulate addition. With the increasing content of reinforcement, more refined grains are produced. The load is transferred from the matrix to more rigid yttrium oxide particles. These factors contributed to escalated microhardness of the reinforced samples. Particulate addition enhanced the wear performance of the material; this might be attributed to increased microhardness and formation of an oxide layer.

Aluminium composites are finding wide applications in various industries, and there is always a requirement of material with enhanced tribological properties. Yttrium oxide particles exhibit improved mechanical properties, and their interaction with the aluminium matrix has not been studied much in the past. So, in this work, yttrium oxide incorporated aluminium matrix is studied.

Mechanical properties are highly sensitive to the microstructure, and these are indirectly related to solidification parameters and processing conditions. AA7075 possesses lightweight and excellent properties as structural material which can be optimized with SiCp addition and a good fabrication technique.

7000 series aluminium alloys exhibit the highest mechanical properties. They are used for high-strength structural applications such as aircraft parts and sporting goods. The desirable properties of these alloys are: low density, high stiffness, specific strength, good wear resistance and creep resistance. The focus of this work is to investigate the microstructure of composites formed by the dispersion of silicon carbide particles (SiC) into AA7075 by stir casting processes. 7075 Al alloy is reinforced with 10 and 15 wt.% SiCp of size 10–20 µm by stir casting process. The composites have been characterized by X-ray diffraction and scanning electron microscopy, differential thermal analysis and electron probe microscopic analysis.

SiCp distribution and interaction with AA7075 matrix have been studied. AA7075/10 wt.%/SiCp (10–20 µm) and AA7075/15 wt.%/SiCp (10–20 µm) composites microstructure showed excellent SiCp distribution into AA7075 matrix. In addition, no evidence of secondary chemical reactions has been observed in X-ray diffraction and electron probe microscopic analysis.

Little experimental work has been reported so far about effect of addition of 10 and 15 wt.% SiCp of size (10–20 µm) on the microstructure of 7075 Al alloy fabricated by stir casting process. The present investigation has been carried out to study the microstructure and carry out XRD, DTA and EPMA analysis of 7075 Al alloy, 10 and 15 wt.% SiCp of size (10–20 µm) composite and detect the interfacial reactions with the objective to minimize the formation of Al4C3.

Parts that are to be used in aircraft, satellites, automobiles and ships should have sound microstructure. Components made from AA6082/Si₃N₄ and AA6082/SiC composites are in demand from industries. Hence, these components are to be fabricated by suitable technique at the appropriate value of process parameters. The purpose of this paper is Microstructure analysis of AA6082/Si3N4 and AA6082/SiC composites

AA6082/Si₃N₄ and AA6082/SiC composites are successfully fabricated using the stir casting process. Their microstructures have been analyzed. This has been done at different magnification. The effect of the addition of Si₃N₄ and SiC particles in the 6082 aluminum alloy is investigated. Microstructure of AA6082/Si₃N₄ and AA6082/SiC composites are also compared. Results show that Si₃N₄ and SiC particles have good wettability with AA6082. These reinforcement particles are homogeneously distributed in the matrix of AA6082.

There are no adverse effects of reactions in the microstructure of AA6082/Si₃N₄ and AA6082/SiC composites. There is not much difference between the distribution and interfacial characteristics of Si₃N₄ and SiC particles. AA6082/Si₃N₄ and AA6082/SiC composites have good properties. This is high strength at low density. Due to which they become suitable for the aircraft and space industry. So far, SiC, Al₂O₃ and tungsten carbide have been mostly used as reinforcements with different grades of aluminum alloy.

Not much experimental work is found with Si₃N₄ and SiC particles as reinforcement with AA6082. The novelty of this research work is that an effort has been made to fabricate AA6082/Si₃N₄ and AA6082/SiC composites at such values of process parameters, by stir casting process, so that sound and defect free microstructure is obtained. Microstructure of AA6082/Si₃N₄ and AA6082/SiC composites is also compared, to find which is better.

This investigation aims to analyze the steel-flux interface level fluctuation because of electromagnetic stirring and its process parameters in a continuous casting billet mold.

An un-coupled numerical model for electromagnetic field generation and a coupled numerical model of electromagnetic field and two-phase fluid flow have been developed. The two-phase fluid flow has been modeled using volume of fluid method, in which externally generated time-varying electromagnetic field is coupled and analyzed using magnetohydrodynamic method. Top surface standing wave stability criteria are used to study the criticality of interface stability.

Results show that application electromagnetic field for stirring increases the interface level fluctuation, specifically at the mold corners and near the submerged entry nozzle. The increase in current intensity and stirrer width barely affect the interface level. However, interface level fluctuation increases considerably with increase in frequency. Using stability criteria, it is found that at 20 Hz frequency, the ratio of height to wavelength of interface wave increases much above the critical value. The iso-surface of the interface level shows that at 20 Hz frequency, mold flux gets entrapped into the liquid steel.

The model may be used during optimization of in-mold electromagnetic stirrer to avoid mold flux entrapment and control the cast quality.

The study of mold level fluctuation in the presence of in-mold electromagnetic stirrer has rarely been reported. The criticality of stirrer process parameters on level fluctuation has not been yet reported. This study lacks in experimental validation; however, the findings will be much useful for the steelmakers to reduce the casting defects.

The purpose of present investigation is to analyze the in-mold electromagnetic stirring (M-EMS) process and the effect of stirrer frequency on fluid flow and solidification in a continuous casting billet caster mold.

A hybrid approach involving finite element and finite volume method has been used for the study. Finite element model is used to calculate time variable magnetic field, which is further coupled with fluid flow and solidification equations for magneto-hydrodynamic analysis with finite volume model.

Results show that though superheat given to steel before its entry into the mold is quickly removed, solid shell formation is delayed by the use of M-EMS. Final solid shell thickness, however, is slightly reduced. Increase in frequency is found to increase the magnetic flux density and tangential velocity of liquid steel and decrease in diameter of liquid core.

The work is of great industrial relevance. The model may be used to design industrial setup of in-mold electromagnetic stirrer and process could be analyzed and optimized numerically.

The paper evaluates the influence of M-EMS and its frequency on solidification and flow behavior in the continuous casting mold. The iso-surface temperatures from pouring temperature to liquidus temperature inside the mold have been shown. The findings may be useful for the steelmakers to reduce the defect in continuous casting.