Search results

The purpose of this paper is to report the first of four planned fire experiments on the 9.1 × 6.1 m steel composite floor assembly as part of the two-story steel framed building constructed at the National Fire Research Laboratory.

The fire experiment was aimed to quantify the fire resistance and behavior of full-scale steel–concrete composite floor systems commonly built in the USA. The test floor assembly, designed and constructed for the 2-h fire resistance rating, was tested to failure under a natural gas fueled compartment fire and simultaneously applied mechanical loads.

Although the protected steel beams and girders achieved matching or superior performance compared to the prescribed limits of temperatures and displacements used in standard fire testing, the composite slab developed a central breach approximately at a half of the specified rating period. A minimum area of the shrinkage reinforcement (60 mm²/m) currently permitted in the US construction practice may be insufficient to maintain structural integrity of a full-scale composite floor system under the 2-h standard fire exposure.

This work was the first-of-kind fire experiment conducted in the USA to study the full system-level structural performance of a composite floor system subjected to compartment fire using natural gas as fuel to mimic a standard fire environment.

Catastrophe of steel-structured bridges due to progressive localized corrosion may lead to a major loss in terms of life and cost if not monitored continuously or periodically. The purpose of this paper is to present a vibration-based strategy to assess the severity and monitor the deterioration caused by corrosion-induced localized damage in a simply-supported steel beam.

The threshold damage level is defined up to the yield limit of a simply supported steel beam of size ISMB 150 × 8 × 5 under three-point bending test and the progressive damage is induced through a continuous accelerated corrosion test. Change in the fundamental natural frequency due to localized damage in the experimental beam and the modulus of elasticity (E) in the corroded zone of an updated finite element (FE) model is evaluated.

The updated FE model of the damaged beam shows a clear trend with the progressive damage of the beam and, hence, can be used to monitor the severity of damage and remaining capacity assessment of the monitored beam.

Steel-structured bridges are prone to localized corrosion attack, and there are no standardized process or predictive model available by international steel design codes on how to consider corrosion damage in the condition assessment analysis. The vibration-based methods have gained popularity for condition assessment, and are mostly confined to damage assessment of corroded reinforced concrete (RC) beams. In this work, a vibration-based approach is presented for degradation assessment of steel beam due to progressive localized corrosion using modal hammer test.

In this study, tests were conducted to investigate the effect of different concretes on the behaviour of reinforced concrete beams with central splices. Five beam specimens were prepared using different concrete mixes in their splice regions. Experimental results indicated that the bond failure of the spliced rebars governed the ultimate flexural behaviour of all specimens, except the one cast with steel fibres. A small increase in flexural strength was found for both the spliced beams cast with high‐strength concrete and steel fibres. Moreover, use of high‐strength concrete and steel fibrous concrete led to a remarkable improvement in the beam's displacement capacity. The effect of pulverised fuel ash on the splice performance was insignificant while the introduction of silica fume caused improvements in loading capacity and ductility.

Due to the enormous increase in economic development, structural steel material gives an advantage for the construction of stadiums, factories, bridges and cities building design. The purpose of this study is to investigate the behaviour of bending, buckling and torsion for I-beam steel section with and without web opening using non-linear finite element analysis.

The control model was simulated via LUSAS software with the four main parameters which included opening size, layout, shape and orientation. The analysis used a constant beam span which is 3.5 m while the edge distance from the centre of the opening to the edge of the beam is kept constant at 250 mm at each end.

The analysis results show that the optimum opening size obtained is 0.65 D while optimum layout of opening is Layout 1 with nine web openings. Under bending behaviour, steel section with octagon shapes of web opening shows the highest yield load, yield moment and thus highest structural efficiency as compared to other shapes of openings. Besides, square shape of web opening has the highest structural efficiency under buckling behaviour. The lower buckling load and buckling moment contribute to the higher structural efficiency.

Further, the square web opening with counter clockwise has the highest structural efficiency under torsion behaviour.

Basically, connections are used to transfer the force supported by structural members to other parts of the structure. The flush end-plate bolted beam to column connection is one type that has been widely used because of its simplicity in fabrication and rapid site erection. The purpose of this study is to determine the moment-rotation curve, moment of resistance (MR) and mode of failure, and the results were compared with existing results for normal flat web connections.

In this study, the connection modeled was the flush end-plate welded with triangular web profile (TriWP) steel beam section and then bolted to a UKC column flange. The bolted flush end-plate semi-rigid beam to column connection was modeled using finite element software. The specimen was modeled using LUSAS 14.3 finite element software, with dimensions and parameters of the finite element model sizes being 200 × 200 × 49.9 UKC, 200 × 100 × 17.8 UKB and 200 × 100 with a thickness of 20 mm for the endplate.

It can be concluded that the MR obtained from the TriWP steel beam section is different from that of the normal flat web steel beam by 28%. The value of MR for the TriWP beam section is lower than that of the normal flat web beam section, but the moment ultimate is higher by 21% than the normal flat web. Therefore, it can be concluded that the TriWP section can resist more acting force than the normal flat web section and is suitable to be used as a new proposed shape to replace the normal flat web section for a certain steel structure based on the end-plate connection behavior.

As a result, the TriWP section has better performance than the flat web section in resisting MR behavior.

The purpose of the study was to investigate the spalling phenomenon in ultra-high performance fibre reinforced concrete (UHPFRC) beams on exposure to a standard fire curve (ISO 834) under a sustained load.

The variables in this study were steel fibre dosage, polypropylene (PP) fibres and loading levels. The research investigated seven beams – three of which contained steel fibres with 2 vol.%, another three had steel fibres with 4 vol.% dosage and the seventh beam had a combination of steel fibres (2 vol.%) and PP fibres (4 kg/m³). The beams were tested for 1 h under three loading levels (20, 40 and 60 per cent) based on the ambient temperature ultimate flexural strength of the beam.

Spalling was affected by the loading levels; it exacerbated under the load level of 40 per cent, whereas under the 60 per cent load level, significantly less spalling was recorded. Under similar loading conditions, the beams containing steel fibres with a dosage of 4 vol.% spalled less than the beams with fibre contents of 2 vol.%. This was attributed to the additional tensile strength provided by the excess steel fibres. The presence of PP fibres eliminated spalling completely.

There is insufficient research into the performance of UHPFRC beams at elevated temperature, as most studies have largely focussed on columns, slabs and smaller elements such as cubes and cylinders. This study provides invaluable information and insights of the influence of parameters such as steel fibre dosage, PP fibres, loading levels on the spalling behaviour and fire endurance of UHPFRC beams.

This paper aims to investigate the predicted temperature behaviour of the protected cellular steel beam (CSB) with circular web openings at elevated temperature through finite element simulation.

Temperature development along the CSB were analysed and used for parametric investigation. In addition, this research paper investigates the novelty application of various intumescent coating thicknesses covering the whole CSB to cut down the temperature development along the beam section.

From the simulation outcomes, it shows that intumescent coating has a significant effect in reducing the temperature development along the CSB section. Thicker intumescent coating contributes to a higher temperature drop at the bottom tee section than the upper tee section.

The use of structural CSB has gained popularity among engineers and architects. This type of beam allows serviceability ducts and pipes to pass through the main steel web section under the flooring system, thus providing larger headroom for designers. Nevertheless, in any structural steel building, it is highly risky for CSB to be exposed to fire hazard if it were triggered accidentally. To mitigate and reduce fire exposure risk which might compromise the strength and stiffness of CSB, a passive fire protection is proposed to minimise the risk. One of the common passive fire protection materials used for steel beam section is intumescent coating. Intumescent coating is by far the cheapest solution to protect CSB as compared to other passive fire protection system. Intumescent coating can absorb some portion of heat exposure which subsequently translates a lower temperature development along the CSB section.

Establishing toughness performance in concrete using steel fibres is well understood, and design guides are available to assist with this process. What is less readily understood is the use of Type 2 synthetic fibres to provide toughness. This problem is exacerbated by the wide range of synthetic fibres available, with each different fibre providing different structural properties. This paper seeks to address this issue.

The paper examines the relative pull‐out values of two single fibre types, i.e. steel and Type 2 synthetic fibres. The pull‐out test results have informed the doses of fibre additions to beams which have been used to equate near equal toughness performance for each fibre type.

The results show that synthetic Type 2 fibres, when used at a prescribed additional volume, can provide toughness equal to steel fibre concrete.

The scientific study of fibre pull‐out behaviour is well understood and described herein under additional reading. Practical testing to show contractors and clients how to balance the dose of fibres in concrete, so that synthetic fibres could be used as a steel fibre replacement, is not well researched. This paper bridges the information gap.

This paper aims to investigate the fire performance of composite beams when considering the hogging moment resistance of the fin-plate beam-to-girder joints including the effect of continuity of reinforcements.

Experiments on composite beams with fin-plate joints protected only at the beam ends are conducted. The test parameter is the specification of reinforcement, which affects the rotational restraint of the beam ends. In addition, a simple method for predicting the failure time of the beam using an evaluation model based on the bending moment resistance of the beam considering the hogging moment resistance of the fin-plate joint and the reinforcement is also presented.

The test results indicate that the failure time of the beam is extended by the hogging moment resistance of the joints. This is particularly noticeable when using a reinforcing bar with a large plastic deformation capability. The predicted failure times based on the evaluation method corresponded well with the test results.

Recent studies have proposed large deformation analysis methods using FEM that can be used for fire-resistant design of beams including joints, but these cannot always be applicable in practice due to the cost and its complexity. Our method can consider the hogging moment resistance of the joint and the temperature distribution in the axial direction using a simple method without requirement of FEM.

In the case of machines, structures and assemblies, the crack generation and propagation is becoming a great concern, especially in airplane wings, turbine blades and such other applications. This is because these parts are very large in size and the crack size is very small, i.e. in microns. Hence, there is an important need to locate the crack and to find its severity before it starts to propagate and also to detect these parameters by on-site non-destructive testing methods. This paper aims to develop and test the methodology to locate an unknown single open crack in steel cantilever beam along with its severity.

This study covers analytical, numerical and experimental analysis for healthy and cracked beams. Vibration-based approach and finite element analysis (FEA) approach is used for analytical and numerical study respectively. Own designed and dedicated experimental set-up is used for testing purpose along with fast fourier transform analyzer. An anti-resonance technique is used to locate and to find the severity of unknown crack. The statistical approach helps to validate the results.

The comparison of the natural frequency of healthy and cracked steel cantilever beam shows that the crack in the beam reduces its natural frequency. The accuracy of results is achieved by finding actual density and Young's modulus of steel specimen under consideration. It is helpful to verify the health of the non-cracked beam by applying dye testing. The study of natural frequency and anti-resonance gives the location of crack and its depth also. The FEA approach proved to be an important tool for numerical analysis of cracked beam.

The research is limited to steel material and surface cracks only.

Practically, this study highlights how to locate a surface crack in steel beam along with its depth, i.e. severity with great accuracy. Identification of the factors such as location and depth of a crack provide the severity of damage in airplane wings, turbine blades, bridges and many more, and thereby, it helps in safety at working vicinity.

The identification and solutions of current research helps to predict the operational life of machine elements such as airplane wings, turbine blades, bridges and many more, and thereby, it helps in the safety of people in working vicinity of such structures.

The work presented, is based on original research and experimentation. This work is valued contribution in the field of methodologies applied for fault detection in structures and also determining its correctness by numerical and experimental work.