Search results

In this special feature details are given of those British paints which can be described as corrosion‐resistant primers, both one‐ and two‐pack. The materials are generally classified according to the base or pigment which actively prevents corrosion—e.g. metallic zinc in zinc/epoxy formulations— or by the base which produces a barrier action against corrosion, e.g. bitumen in bituminous paints. Exceptions to this are the etching primers, which are separately classified. About 300 primers are described, the manufacturers' names and addresses being cross‐indexed and listed separately on page 48.

This paper aims to consolidate the results of various researchers focusing the different applications, so that this paper could become the torch bearer for the futuristic researchers working in the domain of cold gas dynamics spray coating.

A study on the cold spray coating is presented by summarizing the data present in literature. Important factors such as coating temperature, pressure, coating thickness, particle size, which affect the erosion-corrosion (E-C) resistance, physical and mechanical properties of boiler steel are stated. This paper also addresses the use of cold spray coating and compares it with other different thermal spray processes.

From the literature review, it was noticed that cold spray technology is best as compare to other thermal spray processes to reduce porosity, increase hardness, adhesion strength and retention in properties of feedstock powders.

Cold spray coating technology has a great potential in almost every field especially in restoration of surfaces, generation of complex surface, biomedical application, resist hot corrosion, wear, oxidation and erosion corrosion.

The purpose of this study is to investigate the effect of the injection angle α on the spray structures of an air-blast atomizer and help enhance the understanding of droplet-gas mixing process in such atomizers in the engineering domain.

The phenomena in the air-blast atomizer were numerically modelled using the computational fluid dynamics software Fluent 17.2. The Euler-Lagrange approach was applied to model the droplet tracking and droplet-gas interaction in studied cases. The standard k-ε model was used to simulate the turbulent flow. A model with a modified drag coefficient was used to consider the effects of the bending of the liquid column and its penetration in the primary breakup region. The Kelvin-Helmholtz, Rayleigh-Taylor model was applied to consider the secondary breakup of the droplets.

The basic spatial distribution and spray structures of the droplets corresponding to the angled liquid jet (α = 60°) were similar to those reported in liquid jets injected transversely into a gaseous crossflow studies. The injection angle α did not considerably influence the averaged Sauter to mean diameter (SMD) of the cross-sections. However, the spray structures pertaining to α = 30°, α = 60° and α = 90° were considerably different. In the case of the atomizer with multiple injections, a “collision region” was observed at α = 60° and characterized by a higher ci and larger averaged SMD in the central parts of the cross-sections.

The injection angle α is a key design parameter for air-blast atomizers. The findings of this study can help enhance the understanding of the droplet-gas mixing process in air-blast atomizers. Engineers who design air-blast atomizers and face new challenges in the process can refer to the presented findings to obtain the desired atomization performance. The code has been validated and can be used in the engineering design process of the gas-liquid jet atomizer.

Model Maker (MM) is a commercial rapid prototyping (RP) system using tiny jets to deposit thermoplastic materials onto a platform to build physical models and the associated support structures. Also, a cutter is employed to plane off the deposited surface in order to maintain smaller layer thickness and hence, model accuracy. The model’s accuracy is mainly affected by the profile layer thickness. The interior filling does not affect the model accuracy or layer thickness very much, but it significantly affects the building time. Hence, a new interior fast filling of MM using a spraying nozzle is proposed in this paper. The detail design, construction, and evaluation of the new proposed fast interior‐spraying process are presented. The results show that the building time using spaying nozzle is only 15 per cent of the time used by the original process.

Zinc was well established as a protective coating for steel before metal spraying was introduced on a commercial scale, and it was natural that sprayed zinc should be to the fore amongst sprayed metal coatings, a position which it has never lost. During the last 15 years, wide fields of usefulness have been developed for zinc‐sprayed coatings which are often peculiar to them. Today it is rare for a decision to have to be made as to whether or not spraying or galvanizing should be used, the controlling factors in most cases being obvious. The use of zinc‐sprayed coatings on large structures, usually on site, is well known, but there has been comparatively little published information on its many other applications.

Plasma spray coating technologies are capable of depositing a wide range of compositions without significantly heating the substrate. The objective is to characterise plasma sprayed metallic coatings on a Fe‐based superalloy.

NiCrAlY, Ni‐20Cr, Ni3Al and Stellite‐6 metallic coatings were deposited on a Fe‐based superalloy (32Ni‐21Cr‐0.3Al‐0.3Ti‐1.5Mn‐1.0Si‐0.1C‐Bal Fe) by the shrouded plasma spray process. The coatings were characterised in relation to coating thickness, porosity, microhardness and microstructure. The high temperature oxidation behaviour of the coatings was investigated in brief. The techniques used in the present investigation include metallography, XRD and SEM/EDAX.

All the coatings exhibited a lamellar structure with distinctive boundaries along with the presence of some porosity and oxide inclusions. The microhardness of the coatings was observed to vary with the distance from the coating‐substrate interface. The St‐6 coating had the maximum microhardness, whereas the lowest hardness was exhibited by the Ni3Al coating. The phases revealed by XRD of the coatings confirmed the formation of solid solutions, whereas EDAX analysis of the as‐sprayed coatings confirmed the presence of basic elements of the coating powders. So far as high temperature oxidation behaviour is concerned, all of the coatings followed the parabolic rate law and resulted in the formation of protective oxide scales on the substrate superalloy.

The plasma spray process provides the possibility of developing coatings of Ni3Al as well as commercial available NiCrAlY, Ni‐20Cr and St‐6 powders on Fe‐based superalloy Superfer 800H

This paper seeks to summarise the results of available research on the use of high velocity oxy‐fuel (HVOF) thermal‐spray technique to provide protection against high temperature corrosion and erosion‐corrosion of materials.

This paper describes one of the recent thermal‐spray processes, namely HVOF thermal‐spray technology and presents a survey of the studies on the use of this technique to provide protection against corrosion and erosion‐corrosion of high temperature alloys, with a special emphasis on boiler steels.

High temperature corrosion and erosion‐corrosion are serious problems observed in steam‐powered electricity generation plants, gas turbines, internal combustion engines, fluidized bed combustors, industrial waste incinerators and recovery boilers in paper and pulp industries. These problems can be prevented by changing the material or altering the environment, or by separating the component surface from the environment. Corrosion prevention by the use of coatings for separating materials from the environment is gaining importance in surface engineering. Amongst various surface modifying techniques, thermal spraying has developed relatively rapidly due to the use of advanced coating formulations and improvements in coating application technology. One of the variants of thermal spraying, namely HVOF has gained popularity in recent times due to its flexibility for in‐situ applications and superior coating properties.

This review covers mainly information that has been reported previously in the open literature, international journals and some well‐known textbooks.

The paper presents a concise summary of information for scientists and academics, planning to start their research work in the area of surface engineering.

This paper fulfils an identified information/resources need and offers practical help to an individual starting out on a career in the area of surface engineering for erosion‐corrosion and wear.

The deposition of particles onto a substrate during the cold spraying (CS) process relies on severe plastic deformation, so there are various micro-defects induced by insufficient deformation and severe crushing. To solve the problems, many post-treat techniques have been used to improving the quality by eliminating the micro-defects. This paper aims to help scholars and engineers in this field a better and systematic understand of CS technology by summarizing the post-treatment technologies that have been investigated recently years.

This review summarizes the types of micro-defects and introduces the effect of micro-defects on the properties of CS coating/additive manufactured, illustrates the post-treatment technologies and its effect on the microstructure and performances, and finally outlooks the future development trends of post-treatments for CS.

There are significant discoveries in post-treatment technology to change the performance of cold spray deposits. There are also many limitations for post-treatment methods, including improved performance and limitations of use. Thus, there is still a strong requirement for further improvement. Hybrid post-treatment may be a more ideal method, as it can eliminate more defects than a single method. The proposed ultrasonic impact treatment could be an alternative method, as it can densify and flatten the CS deposits.

It is the first time to reveal the influence factors on the performances of CS deposits from the perspective of microdefects, and proposed corresponding well targeted post-treatment methods, which is more instructive for improving the performances of CS deposits.

The purpose of this paper is to examine the performance of cold-sprayed Zn15Al alloy coating whether it is capable of protecting magnesium alloy from corrosion, and to compare it with arc-sprayed Zn15Al alloy coating.

In this paper, Zn15Al alloy coating was prepared with CS-6000 cold spraying system and HDX-800 arc-sprayed system. Corrosion behaviors of the two kinds of coatings were examined with potentiodynamic polarization curves methods combined with SEM, EDS, XRD, etc.

Corrosion behavior of cold-sprayed Zn15Al alloy coating is superior to arc-sprayed Zn15Al alloy coating. The bonding strength and density of cold-sprayed Zn15Al alloy coating is much higher than that of arc-sprayed Zn15Al alloy coating. The cold-sprayed coating has a dense structure which separate magnesium from corrosion medium completely. The samples behave as Zn15Al instead of AZ91D alloy. The coating has a low probability of pitting corrosion comparing with cold sprayed Al coating through potentiodynamic polarization curve.

Cold-sprayed Zn15Al coating can be used to improve the anticorrosion performance of magnesium significantly and low down the risk of pitting corrosion of coating.

Cold-sprayed Zn15Al coating is an environmentally friendly anticorrosion method for light alloy, which is also the most effective way among thermal spray, chemical vapor deposition, sol–gel, plating and anodizing or microarc oxidation.

The present paper used cold spray method to deposit Zn15Al coating, which has an overwhelming performance both in physical and anticorrosion to traditional thermal spray method.

Spray curing has become the preferred curing method for most cement concrete members because of its lower cost and sound effect. However, the spray curing quality of members is vulnerable to random variation environment factors and anthropogenic interferences. This paper aims to introduce the machine learning algorithm into the spray curing system to optimize its control method to improve the spray curing quality of members.

The critical parameters affecting the spray curing quality of members were collected through experiments, such as the temperature and humidity of the member's surface, the temperature, humidity and wind speed of the environment. The C4.5 algorithm was used as a weak classifier algorithm, and the AdaBoost.M1 algorithm was used to cascade multiple weak classifiers to form a robust classifier according to the collected data.

The results showed that the model constructed by the AdaBoost.M1 algorithm had achieved higher accuracy and robustness among the two algorithms. Based on the classification model built by the AdaBoost.M1 algorithm, the spray curing system can cause automatic decision-making spray switching according to the member's real-time curing state and environment.

With the classification model constructed by the AdaBoost.M1 algorithm, the spray curing system can overcome the disadvantages that external factors greatly influence the current control method of the spray curing system, and the intelligent control of the spray curing system was realized to a certain extent. This paper provides a reference for applying machine learning algorithms in the intellectual transformation of bridge construction equipment.