Search results

This paper aims to discuss the successful 3D printing of styrene–ethylene–butylene–styrene (SEBS) block copolymers using solvent-cast 3D printing (SC-3DP) technique.

Three different Kraton grade SEBS block copolymers were used to prepare viscous polymer solutions (ink) in three different solvents, namely, toluene, cyclopentane and tetrahydrofuran. Hansen solubility parameters (HSPs) were taken into account to understand the solvent–polymer interactions. Ultraviolet–visible spectroscopy was used to analyze transmittance behavior of different inks. Printability of ink samples was compared in terms of shape retention capability, solvent evaporation and shear viscosity. Dimensional deviations in 3D-printed parts were evaluated in terms of percentage shrinkage. Surface morphology of 3D-printed parts was investigated by scanning electron microscope. In addition, mechanical properties and rheology of the SC-3D-printed SEBS samples were also investigated.

HSP analysis revealed toluene to be the most suitable solvent for SC-3DP. Cyclopentane showed a strong preferential solubility toward the ethylene–butylene block. Microscopic surface cracks were present on tetrahydrofuran ink-based 3D-printed samples. SC-3D-printed samples exhibited high elongation at break (up to 2,200%) and low tension set (up to 9%).

SC-3DP proves to be an effective fabrication route for complex SEBS parts overcoming the challenges associated with fused deposition modeling.

To the best of authors’ knowledge, this is the first report investigating the effect of different solvents on physicomechanical properties of SC-3D-printed SEBS block copolymer samples.

The purpose of this paper is to fabricate pre-existing geometries of the stents using solvent cast 3D printing (SC3P) and encapsulation of each stent with heparin drug by using aminolysis reaction.

The iron pentacarbonyl powder and poly-ɛ-caprolactone blend (PCIP) were used to print stent designs of Art18z, Palmaz-Schatz and Abbott Bvs1.1. The properties of antithrombosis, anticoagulation and blood compatibility were introduced in the stents by conjugation of heparin drug via the aminolysis process. The aminolysis process was confirmed by energy dispersive X-ray spectroscopy and Fourier transform infrared spectroscopy due to presence of amide group and nitrogen peak in the respective analysis. Biological studies were performed to depict the cell viability, hemocompatibility and antithrombotic properties. Besides, mechanical behaviors were analyzed to study the behavior of the stents under radial compression load and bending load.

The amount of heparin immobilized on the Art18z, Palmaz-Schatz and Abbott Bvs1.1 stents were 255 ± 27, 222 ± 30 and 212 ± 13 µg, respectively. The cell viability studies using L929 fibroblast cells confirmed the cytocompatibility of the stents. The heparinized SC3P printed stents displayed excellent thrombo-resistance, anticoagulation properties and hemocompatibility as confirmed by blood coagulation analysis, platelet adhesion test and hemolysis analysis. Besides, mechanical behavior was found in context of the real-life stents. All these assessments confirmed that the developed stents have the potential to be used in the real environment of coronary arteries.

Various customized shaped biodegradable stents were fabricated using 3D printing technique and encapsulated with heparin drug using aminolysis process.

The implications of metallic biomaterials involve stress shielding, bone osteoporosis, release of toxic ions, poor wear and corrosion resistance and patient discomfort due to the need of second operation. This study aims to use additive manufacturing (AM) process for fabrication of biodegradable orthopedic small locking bone plates to overcome complications related to metallic biomaterials.

Fused deposition modeling technique has been used for fabrication of bone plates. The effect of varying printing parameters such as infill density, layer height, wall thickness and print speed has been studied on tensile and flexural properties of bone plates using response surface methodology-based design of experiments.

The maximum tensile and flexural strengths are mainly dependent on printing parameters used during the fabrication of bone plates. Tensile and flexural strengths increase with increase in infill density and wall thickness and decrease with increase in layer height and wall thickness.

The present work is focused on bone plates. In addition, different AM techniques can be used for fabrication of other biomedical implants.

Studies on application of AM techniques on distal ulna small locking bone plates have been hardly reported. This work involves optimization of printing parameters for development of distal ulna-based bone plate with high mechanical strength. Characterization of microscopic fractures has also been performed for understanding the fracture behavior of bone plates.

The main purpose of this research work is to study the effect of poly lactic acid (PLA) addition into poly (e-caprolactone) (PCL) matrices, as well the influence of the mixing process on the morphological, thermal, chemical, mechanical and biological performance of the 3D constructs produced with a novel biomanufacturing device (BioCell Printing).

Two mixing processes are used to prepare PCL/PLA blends, namely melt blending and solvent casting. PCL and PCL/PLA scaffolds are produced via BioCell Printing using a 300-μm nozzle, 0/90° lay down pattern and 350-μm pore size. Several techniques such as scanning electron microscopy (SEM), simultaneous thermal analyzer (STA), nuclear magnetic resonance (NMR), static compression analysis and Alamar BlueTM are used to evaluate scaffold's morphological, thermal, chemical, mechanical and biological properties.

Results show that the addition of PLA to PCL scaffolds strongly improves the biomechanical performance of the constructs. Additionally, polymer blends obtained by solvent casting present better mechanical and biological properties, compared to blends prepared by melt blending.

This paper undertakes a detailed study on the effect of the mixing process on the biomechanical properties of PCL/PLA scaffolds. Results will enable to prepare customized PCL/PLA scaffolds for tissue engineering applications with improved biological and mechanical properties, compared to PCL scaffolds alone. Additionally, the accuracy and reproducibility of by the BioCell Printing enables to modulate the micro/macro architecture of the scaffolds enhancing tissue regeneration.

Fabrication of customized products in low volume through conventional manufacturing incurs a high cost, longer processing time and huge material waste. Hence, the concept of additive manufacturing (AM) comes into existence and fused deposition modelling (FDM), is at the forefront of researches related to polymer-based additive manufacturing. The purpose of this paper is to summarize the research works carried on the applications of FDM.

In the present paper, an extensive review has been performed related to major application areas (such as a sensor, shielding, scaffolding, drug delivery devices, microfluidic devices, rapid tooling, four-dimensional printing, automotive and aerospace, prosthetics and orthosis, fashion and architecture) where FDM has been tested. Finally, a roadmap for future research work in the FDM application has been discussed. As an example for future research scope, a case study on the usage of FDM printed ABS-carbon black composite for solvent sensing is demonstrated.

The printability of composite filament through FDM enhanced its application range. Sensors developed using FDM incurs a low cost and produces a result comparable to those conventional techniques. EMI shielding manufactured by FDM is light and non-oxidative. Biodegradable and biocompatible scaffolds of complex shapes are possible to manufacture by FDM. Further, FDM enables the fabrication of on-demand and customized prosthetics and orthosis. Tooling time and cost involved in the manufacturing of low volume customized products are reduced by FDM based rapid tooling technique. Results of the solvent sensing case study indicate that three-dimensional printed conductive polymer composites can sense different solvents. The sensors with a lower thickness (0.6 mm) exhibit better sensitivity.

This paper outlines the capabilities of FDM and provides information to the user about the different applications possible with FDM.

This work aims to present a guideline for ink development used in extrusion-based direct-write (DW) (also referred to as direct-print [DP]) technique and combine the extrusion with instant photopolymerization to present a solvent-free DP photopolymerization (DPP) method to fill the gap between 3D printing and printing multi-functional 3D structures.

A DP process called DPP was developed by integration of a screw-driven micro-dispenser into XYZ translation stages. The process was equipped with direct photopolymerization to facilitate the creation of 3D structures. The required characteristics of inks used in this technique were simulated through dispersion of fumed silica particles into photocurable resins to transform them into viscoelastic inks. The characterization method of these inks and the required level of shear thinning and thixotropic properties is presented.

Shear thinning and thixotropic properties are necessary components of the inks used in DPP process and other DP techniques. These properties are desirable to facilitate printing and filament shape retention. Extrusion of viscoelastic inks out of a nozzle generates a filament capable of retaining its geometry. Likewise, instant photopolymerization of the dispensed filaments prevents deformation due to the weight of filaments or accumulated weight of layers.

The DPP process with material-reforming methods has been shown, where there remain many shortcomings in realizing a DP-based 3D printing process with instant photopolymerization in existing literature, as well as a standard guideline and material requirements. The suggested method can be extended to develop a new commercial 3D printing system and printable inks to create various functional 3D structures including sensors, actuators and electronics, where nanoparticles are involved for their functionalities. Particularly, an original contribution to the determination of a rheological property of an ink is provided.

Polyurethane (PUR) foam parts are traditionally manufactured using metallic molds, an unsuitable approach for prototyping purposes. Thus, rapid tooling of disposable molds using fused filament fabrication (FFF) with polylactic acid (PLA) and glycol-modified polyethylene terephthalate (PETG) is proposed as an economical, simpler and faster solution compared to traditional metallic molds or three-dimensional (3D) printing with other difficult-to-print thermoplastics, which are prone to shrinkage and delamination (acrylonitrile butadiene styrene, polypropilene-PP) or high-cost due to both material and printing equipment expenses (PEEK, polyamides or polycarbonate-PC). The purpose of this study has been to evaluate the ease of release of PUR foam on these materials in combination with release agents to facilitate the mulding/demoulding process.

PETG, PLA and hardenable polylactic acid (PLA 3D870) have been evaluated as mold materials in combination with aqueous and solvent-based release agents within a full design of experiments by three consecutive molding/demolding cycles.

PLA 3D870 has shown the best demoldability. A mold expressly designed to manufacture a foam cushion has been printed and the prototyping has been successfully achieved. The demolding of the part has been easier using a solvent-based release agent, meanwhile the quality has been better when using a water-based one.

The combination of PLA 3D870 and FFF, along with solvent-free water-based release agents, presents a compelling low-cost and eco-friendly alternative to traditional metallic molds and other 3D printing thermoplastics. This innovative approach serves as a viable option for rapid tooling in PUR foam molding.

There is a rising demand for high-performance 3D printed objects that have established potential applications in the sector of dental, automotive, electronics, aerospace, etc. Thus, to meet the requirements of high-performance 3D printed objects, this study has synthesized, formulated and applied a resorcinol epoxy acrylate (REA) oligomer to a stereolithography (SLA) 3D printer.

Different formulations were developed by blending reactive diluents in the concentration of 10%, 15% and 20%, along with the fixed quantity of photo-initiators in the REA oligomer. The structure of synthesized REA oligomer was confirmed using 13 C nuclear magnetic resonance (NMR) and 1H NMR spectroscopy, and the rheological properties for prepared REA formulations were also evaluated. The ultraviolet (UV)-cured specimens of all REA formulations were thoroughly examined based on physical, chemical, optical, mechanical and thermal properties. The best suitable formulation was selected for SLA 3D printing.

As perceived, UV cured REA specimens exhibit superior mechanical, chemical and thermal properties, portraying the ability to use as a high-performance material. The increase in the concentration of reactive diluents indicated a significant improvement in the properties of REA resin. The 20% diluted formulation achieved excellent compatibility with a SLA 3D printer; thus, 3D objects are cast with good dimensional stability and printability.

Resorcinol-based resins have always been a key additive used to enhance properties in the coating and tire industry. In a new attempt UV, curable REA has been applied to a SLA 3D printer to cast high-performance 3D printed objects.

The purpose of this work is to introduce a novel approach of using additive manufacturing (AM) to produce dense complex ceramic and metallic parts. Powder 3D printing has been gaining popularity due to its ease of use and versatility. However, powder-based methods such as Selective Laser Melting (SLM) and Sintering (SLS), utilizes high power lasers which generate thermal shock conditions in metals and are not ideal for ceramics due to their high melting temperature. Indirect additive manufacturing methods have been explored to address the above issues but have proven to be wasteful and time-consuming.

In this work, a novel approach of producing high density net-shaped prototypes using subtractive sintering (SS) and solvent jetting is developed. AM combined with SS (AM-SS) is a process that includes five simple steps. AM-SS can produce repeatable and reliable results as has been shown in this work.

As a proof-of-concept, a zirconia dental crown with a high density of 97% is fabricated using this approach. Microstructure and properties of the fabricated components are analyzed.

A major advantage of this method is the ability to efficiently fabricate high density parts using either metal powder and more importantly, ceramic powder which is traditionally difficult to densify using AM. Additionally, any powder particle size (including nano) and shape can be used which is not the case for traditional powder-based 3D printing.

The use of physical 3D models has been used in the industry for a while, fulfilling the function of prototypes in the majority of cases where the designers, engineers and manufacturers optimize their designs before taking them into production. In recent years, there has been an increasing number of reports on the use of 3D models in medicine for preoperative planning. In some highly complex surgeries, the possibility of using printed models to previously perform operations can be determining in the success of the surgery. With the aim of providing new functionalities to an anatomical 3D-printed models, in this paper, a cost-effective manufacturing process has been developed. A set of tradition of traditional techniques have been combined with 3D printing to provide a maximum geometrical freedom to the process. By the use of an electroluminescent set of functional paints, the tumours and vessels of the anatomical printed model have been highlighted, providing to this models the possibility to increase its interaction with the surgeon. These set of techniques has been used to increase the value added to the reproduced element and reducing the costs of the printed model, thus making it more accessible.

Successfully case in where the use of a low-cost 3D-printed anatomical model was used as a tool for preoperative planning for a complex oncological surgery. The said model of a 70-year-old female patient with hepatic metastases was functionalized with the aim of increasing the interaction with the surgeons. The analysis of the construction process of the anatomical model based on the 3D printing as a tool for their use in the medical field has been made, as well as its cost.

The use of 3D printing in the construction of anatomical models as preoperative tools is relatively new; however, the functionalization of these tools by using conductive and electroluminescent materials with the aim of increasing the interaction with it by the surgeons is a novelty. And, based on the DIY principles, it offers a geographical limitlessness, reducing its cost without losing the added value.

The process based on 3D printing presented in this paper allows to reproduce low-cost anatomical models by following a simple sequence of steps. It can be done by people with low qualification anywhere with only access to the internet and with the local costs. The interaction of these models with the surgeon based on touch and sight is much higher, adding a very significant value it, without increasing its cost.