Search results

This paper examines the rôle that the squeegee plays in the solder paste printing process. Although the printing of solder paste is only one stage of many in the surface mount assembly process, it is crucial to deposit the correct amounts of solder paste cleanly onto the substrate. The amount of solder paste deposited affects the reliability and strength of the reflowed solder joint. Surface mount component lead pitches are continually being reduced due to the requirements of packing more and more components into a given space on the PCB, and this necessitates a proper understanding of the printing process and in particular of the squeegee which plays an important part in determining paste heights and the occurrence of defects. The paper outlines a model which predicts scooping and skipping in the stencil printing of solder pastes used in the reflow soldering of surface mounted devices. The model is based on the forces acting on the squeegee blade, which determines the paste flow pattern ahead of the squeegee, and on the stencil aperture geometry. The paper also examines the interactions between the paste properties and squeegee material properties. These interactions produce printing defects such as scooping, skipping and wet bridging. Results of an experimental comparison of different types of squeegee blade used in the stencil printing of solder pastes for reflow soldering in SMT, as well as the experimental results for squeegee deformation into stencil apertures, were used for validating the model. The empirically enhanced model which results takes into account the force on the squeegee due to solder paste flow and some of the non‐Newtonian properties of the solder paste. The main utility of the proposed model is the control of solder paste printing quality.

The purpose of this paper is to investigate the effect of different viscosity models (Cross and Al-Ma’aiteh) and different printing speeds on the numerical results (e.g. pressure over stencil) of a numerical model regarding stencil printing.

A finite volume model was established for describing the printing process. Two types of viscosity models for non-Newtonian fluid properties were compared. The Cross model was fitted to the measurement results in the initial state of a lead-free solder paste, and the parameters of a Al-Ma’aiteh material model were fitted in the stabilised state of the same paste. Four different printing speeds were also investigated from 20 to 200 mm/s.

Noteworthy differences were found in the pressure between utilising the Cross model and the Al-Ma’aiteh viscosity model. The difference in pressure reached 33-34% for both printing speeds of 20 and 70 mm/s and reached 31% and 27% for the printing speed of 120 and 200 mm/s. The variation in the difference was explained by the increase in the rates of shear by increasing printing speeds.

Parameters of viscosity model should be determined for the stabilised state of the solder paste. Neglecting the thixotropic paste nature in the modelling of printing can cause a calculation error of even approximately 30%. By using the Al-Ma’aiteh viscosity model over the stabilised state of solder pastes can provide more accurate results in the modelling of printing, which is necessary for the effective optimisation of this process, and for eliminating soldering failures in highly integrated electronic devices.

This paper aims to investigate the effect of physical vapor deposition (PVD)-coated stencil wall aperture on the life span of fine-pitch stencil printing.

The fine-pitch stencil used in this work is fabricated by electroform process and subsequently nano-coated using the PVD process. Stencil printing process was then performed to print the solder paste onto the printed circuit board (PCB) pad. The solder paste release was observed by solder paste inspection (SPI) and analyzed qualitatively and quantitatively. The printing cycle of up to 80,000 cycles was used to investigate the life span of stencil printing.

The finding shows that the performance of stencil printing in terms of solder printing quality is highly dependent on the surface roughness of the stencil aperture. PVD-coated stencil aperture can prolong the life span of stencil printing with an acceptable performance rate of about 60%.

Stencil printing is one of the important processes in surface mount technology to apply solder paste on the PCB. The stencil’s life span greatly depends on the type of solder paste, stencil printing cycles involved and stencil conditions such as the shape of the aperture, size and thickness of the stencil. This study will provide valuable insight into the relationship between the coated stencil wall aperture via PVD process on the life span of fine-pitch stencil printing.

This research aims to study the stencil printing process of the quad flat package (QFP) component with a pin pitch of 0.4 mm. After the optimization of the printing process, the desired inspection specification is determined to reduce the expected total process loss.

Static Taguchi parametric design is applied while considering the noise factors possibly affecting the printing quality in the production environment. The Taguchi quality loss function model is then proposed to evaluate the two types of inspection strategies.

The optimal parameter-level treatment for the solder paste printing process includes a squeegee pressure of 11 kg, a stencil snap-off of 0.14 mm, a cleaning frequency of the stencil once per printing and using an air gun after stencil wiping. The optimal upper and lower specification limits are 119.8 µm and 110.3 µm, respectively.

Noise factors in the production environment are considered to determine the optimal printing process. For specific components, the specification is established as a basis for subsequent processes or reworks.

The study investigates the sub process behaviour in stencil printing of type‐6 and type‐7 particle size distribution (PSD) Pb‐free solder pastes to assess their printing limits.

Two solder pastes were used in a design of experiments approach to find optimal printing parameters

Solder paste printing has been achieved to ultimately produce 30 μm deposits at 60 μm pitch for full area array patterns using a type‐7 Pb‐free solder paste. For a type‐6 PSD solder paste, full area array printing was limited to 50 μm deposits at 110 μm pitch. However, for peripheral printing patterns, 50 μm deposits at 90 μm pitch were obtained. The disparities in the behaviour of the two paste types at different geometries can be attributed to differences in the sub‐processes of the stencil printing. The paste release of the type‐6 paste from the stencil apertures at fine pitch was superior to the type‐7 paste, which may be attributed to the finer particle paste producing an increased drag force along the stencil aperture walls. However, the type‐7 paste was able to fill the smallest aperture openings, ultimately to 30 μm, thus producing full array printing patterns at uniquely small pitches.

This advancement in the stencil printing process has been made possible by refinements to both solder paste design and stencil manufacturing technology. Adjustments in the solder paste rheology have enabled successful printing at ultra fine pitch geometries. This, together with selecting appropriate printing parameters such as printing speed, pressure, print gap and separation speed, allows a practical printing process window. Moreover, advancements in stencil fabrication methods have produced “state‐of‐the‐art” stencils exhibiting very precisely defined aperture shapes, with smooth walls at very fine pitch, thus allowing for improved solder paste release at very small dimensions.

The results can be used to present a low cost solution for Pb‐free flip chip wafer bumping. Furthermore, the results indicate that type‐6 and type‐7 solder pastes should be applied to/selected for specific application geometries.

This paper aims to establish the predictive equations of height, area and volume of printed solder paste during solder paste stencil printing (SPSP) process in surface mount technology (SMT) to better understand the effect of process parameters on the printing quality.

An experiment plan is proposed based on the response surface method (RSM). Experiments with 30 different combinations of process parameters are performed using a solder paste printer. After printing, the volume, area and height of the printed SAC105 solder paste are measured by a solder paste inspection machine. Using RSM, the predictive equations associated with the printing parameters and the printing quality of the solder paste are formed.

The optimal printing parameters are 175.08 N printing pressure, 250 mm/s printing speed, 0.1 mm snap-off height and 15.7 mm/s stencil snap-off speed if the target height of solder paste is 100 µm. As the target printing area of solder paste is 1.1 mm × 1.3 mm, the optimized values of the printing parameters are 140.29 N, 100.52 mm/s, 0.63 mm and 20.25 mm/s. When both the target printing height and area are optimized together, the optimal values for the four parameters are 86.67 N, 225.76 mm/s, 0.15 mm and 1.82 mm/s.

A simple RSM-based experimental method is proposed to formulate the predictive polynomial equations for height, area and volume of printed solder paste in terms of important SPSP parameters. The predictive equation model can be applied to the actual SPSP process, allowing engineers to quickly predict the best printing parameters during parameter setting to improve production efficiency and quality.

The use of fine‐pitch SMD devices has increased the need for accurate and consistent solder paste deposits for reflow soldering. Continued miniaturisation in PCB and SMD lead sizes is presenting the user, paste supplier and print equipment manufacturer with paste printing challenges. Most of these challenges are user‐driven, and are generally met by enhancing associated print equipment and solder paste materials. Recent developments in fine‐particle pastes, water‐soluble and no‐clean pastes are among the improvements in materials. Vision‐assisted stencil aperture and PCB pad alignment, the use of metal squeegees and new stencil fabrication methods are among the latest developments on the equipment side. Printing tests have shown that there is a physical limit for the solder paste printing process, which is defined partly by the nature of the stencil fabrication process, the physical forces and the stencil's ability to meter a precise volume of paste. The challenge as SMD lead sizes decrease is to improve the printing process to match component lead sizes. There is a fear that we are now operating at the very limits of the solder paste printing process. To meet future component developments, there is a need to develop alternative printing processes for solder reflow.

The purpose of this paper is to investigate and minimize the printing-related defects in the surface mount assembly (SMA) process.

This paper uses an experimental approach to explore process parameter and printing defects during the SMA process. Increasing printing performance, various practices of solder paste (Ag3.0/Cu0.5/Sn) storage and handling are suggested. Lopsided paste problem is studied by varying squeegee pressure and the results are presented. Unfilled pads problems are observed for ball grid array (BGA) and quad flat package (QFP) which is mitigated by proper force tuning. In this paper, a comparative study is conducted which evaluates the manifestation of printing offset due to low-grade stencil. The input/output (I/O) boards were oxidized when the relative humidity was maintained beyond 70 per cent for more than 8 h. This pad oxidation problem is overcome by proper printed circuit board (PCB) handling procedures. When the unoptimized line is used, the paste wedged in the stencil and influences the performance of the screen printer, for this reason, an optimized line is proposed that minimize the printing defects.

The key findings are as follows: in the SMA process, printing quality is directly associated with solder paste quality. Experimentally, it is observed that a considerable variance in solder deposition occurred when the front and rear squeegee have different configurations. High-grade and unsoiled stencil results in superior paste deposition and less distinction. Insufficient solder paste and bridge problems also occur in printing when PCB pads are oxidized. Optimized line resolves solder paste clog issues, associated with stencil’s aperture. The cooling arrangement on the conveyor, after reflow, explicates hot jig problem. Control environmental conditions minimized static charges and printing defects.

The preceding studies emphasis mostly on the squeegee pressure, while other important parameters are not completely investigated. Moreover, it is very imperative to concurrently measure all parameters while varying the environmental conditions. This study highlights and provides an experimental approach to various PCB printing defects, and a comparative study has been conducted that concurrently measure all process parameters.

A measurement method has been developed to reveal the viscosity change of solder pastes during stencil printing. This paper aimed to investigate thixotropic behaviour, the viscosity change of a lead-free solder paste (Type 4).

The viscosity change of the solder paste during stencil printing cycles was characterised in such a way that the time-gap between the printing cycles was modelled with a rest period between every rheological measurement. This period was set as 15, 30 and 60 s during the research. The Cross model was fitted to the measurement results, and the η₀ parameter was used to characterise the viscosity change. The number of printing cycles necessary for reaching a stationary state in viscosity was determined for various rest periods.

It was found that the decrease in zero-shear viscosity is significant (25 per cent) in the first cycles, and it starts to become stationary at the sixth-seventh cycles. This means a printing process can provide the appropriate deposits only after the 7th cycle with the investigated Type 4 solder paste.

Time-dependent rheological behaviour of solder pastes was studied in the literature, but only the viscosity change over continuous time at constant shear rates was examined. The time-gap between stencil printing cycles was not considered, and thixotropic behaviour of solder pastes was also neglected. Therefore, the authors developed a measurement set which is able to model the effect of time-gap between printing cycles on the viscosity change of solder pastes.

The purpose of this paper is to study the effect of the electropolishing time of stencil manufacturing parameters and solder‐mask definition methods of PCB pad design parameters on the performance of solder paste stencil printing process for the assembly of 01005 chip components.

During the study, two types of stencils were manufactured for the evaluations: electroformed stencils and electropolished laser‐cut stencils. The electroformed stencils were manufactured using the standard electroforming process and their use in the paste printing process was compared against the use of an electropolished laser‐cut stencil. The electropolishing performance of the laser‐cut stencil was evaluated twice at the following intervals: 100 s and 200 s. The performance of the laser‐cut stencil was also evaluated without electropolishing. An optimized process was established after the polished stencil apertures of the laser‐cut stencil were inspected. The performance evaluations were made by visually inspecting the quality of the post‐surface finishing for the aperture wall and the quality of that post‐surface finishing was further checked using a scanning electron microscope. A test board was used in a series of designed experiments to evaluate the solder paste printing process.

The results demonstrated that the length of the electropolishing time had a significant effect on the small stencil's aperture quality and the solder paste's stencil printing performance. In this study, the most effective electropolishing time was 100 s for a stencil thickness of 0.08 mm. The deposited solder paste thickness was significantly better for the enhanced laser‐cut stencil with electropolishing compared to the conventional electroformed stencils. In this printing‐focused work, print paste thickness measurements were also found to vary across different solder‐mask definition methods of printed circuit board pad designs with no change in the size of the stencil aperture. The highest paste value transfer consistently occurred with solder‐mask‐defined pads, when an electropolished laser‐cut stencil was used.

Due to important improvements in the quality of the electropolished laser‐cut stencil, and based on the results of this experiment, the electropolished laser‐cut stencil is strongly recommended for the solder paste printing of fine‐pitch and miniature components, especially in comparison to the typical laser‐cut stencil. The advantages of implementing a 01005 chip component mass production assembly process include excellent solder paste release, increased solder volume, good manufacture‐ability, fast turnaround time, and greater cost saving opportunities.