Search results
1 – 10 of over 1000A quantitative dynamic solder wettability measurement was used to evaluate the effects of reflow processing on the wettability parameters associated with two non‐lead bearing…
Abstract
A quantitative dynamic solder wettability measurement was used to evaluate the effects of reflow processing on the wettability parameters associated with two non‐lead bearing solders, 96.5% Sn/3.5% Ag and 58% Bi/42% Sn. An experimental design approach employing full factorial experiments was formulated to investigate the solder wetting dependence of the reflow parameters: atmosphere, peak reflow temperature, time above liquidus and metallisation. Solder wettability was determined with respect to the final degree of spread and the extent of solder wetting onto the lands of surface mount components. The solder alloy composition of 96.5% Sn/3.5% Ag was found to exhibit better wetting characteristics than the 58% Bi/42% Sn alloy. This wetting behaviour was enhanced under the reflow conditions of a nitrogen atmosphere and the use of a gold metallisation. The wetting of the conventional 63% Sn/37% Pb solder alloy was improved over the comparatively processed 58% Bi/42% Sn alloy. However, the 63% Sn/37% Pb solder alloy displayed a greater sensitivity to reflow atmosphere than the 96.5% Sn/3.5% Ag alloy, which generally exhibited better wetting characteristics than the Sn/Pb alloy.
Rizk Mostafa Shalaby and Mohamed Saad
The purpose of the present work is to study the impacts of rapid cooling and Tb rare-earth additions on the structural, thermal and mechanical behavior of Bi–0.5Ag lead-free…
Abstract
Purpose
The purpose of the present work is to study the impacts of rapid cooling and Tb rare-earth additions on the structural, thermal and mechanical behavior of Bi–0.5Ag lead-free solder for high-temperature applications.
Design/methodology/approach
Effect of rapid solidification processing on structural, thermal and mechanical properties of Bi-Ag lead-free solder reinforced Tb rare-earth element.
Findings
The obtained results indicated that the microstructure consists of rhombohedral Bi-rich phase and Ag99.5Bi0.5 intermetallic compound (IMC). The addition of Tb could effectively reduce the onset and melting point. The elastic modulus of Tb-containing solders was enhanced to about 90% at 0.5 Tb. The higher elastic modulus may be attributed to solid solution strengthening effect, solubility extension, microstructure refinement and precipitation hardening of uniform distribution Ag99.5Bi0.5 IMC particles which can reasonably modify the microstructure, as well as inhibit the segregation and hinder the motion of dislocations.
Originality/value
It is recommended that the lead-free Bi-0.5Ag-0.5Tb solder be a candidate instead of common solder alloy (Sn-37Pb) for high temperature and high performance applications.
Details
Keywords
Zilong Wang, JiaCheng Zhou, Fang Liu, Yuqin Wu and Nu Yan
The purpose of this paper is to study the microstructure and properties of Sn-3.5Ag and Sn-3.5Ag-0.5Sb lead-free solder alloys with and without a rotating magnetic field (RMF).
Abstract
Purpose
The purpose of this paper is to study the microstructure and properties of Sn-3.5Ag and Sn-3.5Ag-0.5Sb lead-free solder alloys with and without a rotating magnetic field (RMF).
Design/methodology/approach
Optical microscopy, scanning electron microscopy and X-ray diffraction were used to analyze the effect of an RMF on the microstructure of the solders. Differential scanning calorimetry was used to study the influence of the RMF on the thermal characteristics of the solders. The mechanical properties of the alloys were determined by tensile measurements at different strain rates.
Findings
The ß-Sn grains and intermetallic compounds for the Sn-3.5Ag and Sn-3.5Ag-0.5Sb lead-free solder alloys were refined under an RMF, and the morphology of the ß-Sn grains changed from dendritic to equiaxed. The pasty range was significantly reduced under an RMF. The ultimate tensile strength (UTS) of Sn-3.5Ag improved under the RMF, whereas the UTS of Sn-3.5Ag-0.5Sb decreased slightly. The addition of Sb to the Sn-3.5Ag alloy significantly enhanced the UTS and elongation (El.%) of the samples. The UTS of the solder increased with increasing strain rate.
Originality/value
The results revealed that the application of RMF in the molten alloy had a significant effect on its microstructure and mechanical properties. The thermal characteristics of the Sn-3.5Ag and Sn-3.5Ag-0.5Sb solder alloys were improved under the RMF. This research is expected to fill a knowledge gap regarding the behaviour of Sn-Ag solder alloys under RMF.
Details
Keywords
Madhuri Chandrashekhar Deshpande, Rajesh Chaudhari, Ramesh Narayanan and Harishwar Kale
This study aims to develop indium-based solders for cryogenic applications.
Abstract
Purpose
This study aims to develop indium-based solders for cryogenic applications.
Design/methodology/approach
This paper aims to investigate mechanical properties of indium-based solder formulations at room temperature (RT, 27 °C) as well as at cryogenic temperature (CT, −196 °C) and subsequently to find out their suitability for cryogenic applications. After developing these alloys, mechanical properties such as tensile and impact strength were measured as per American Society for Testing and Materials standards at RT and at CT. Charpy impact test results were used to find out ductile to brittle transition temperature (DBTT). These properties were also evaluated after thermal cycling (TC) to find out effect of thermal stress. Scanning electron microscope analysis was performed to understand fracture mechanism. Results indicate that amongst the solder alloys that have been studied in this work, In-34Bi solder alloy has the best all-round mechanical properties at RT, CT and after TC.
Findings
It can be concluded from the results of this work that In-34Bi solder alloy has best all-round mechanical properties at RT, CT and after TC and therefore is the most appropriate solder alloy amongst the alloys that have been studied in this work for cryogenic applications
Originality/value
DBTT of indium-based solder alloys has not been found out in the work done so far in this category. DBTT is necessary to decide safe working temperature range of the alloy. Also the effect of TC, which is one of the major reasons of failure, was not studied so far. These parameters are studied in this work.
Details
Keywords
This paper aims to investigate the effect of In and Sb additions on the thermal behavior and wettability of Sn-3.5Ag-xIn-ySb (x = 0, 1.0 and 1.5 Wt.%, y = 0, 1.0, 1.4 and 2.1…
Abstract
Purpose
This paper aims to investigate the effect of In and Sb additions on the thermal behavior and wettability of Sn-3.5Ag-xIn-ySb (x = 0, 1.0 and 1.5 Wt.%, y = 0, 1.0, 1.4 and 2.1 Wt.%) solder alloys.
Design/methodology/approach
The thermal behavior of the Pb-free solder alloys was studied using differential scanning calorimetry. Wetting balance experiments were performed in accordance with the IPC standard, IPC-TM-650 and at a temperature of 260°C. Also, a solder spread test was performed on a Cu surface finish using the JIS-Z-3197 solderability standard.
Findings
It is shown that among the selected Sn-3.5Ag-xIn-ySb (x = 0, 1.0 and 1.5 Wt.%, y = 0, 1.0, 1.4 and 2.1 Wt.%) alloys, Sn-3.5Ag-1.5In-1Sb showed the lowest melting point and the lowest undercooling temperature. The best wettability was achieved when the In and Sb contents were approximately 1.5 and 1.0 Wt.%, respectively. The effect of the combined addition of In and Sb on solder spreadability on a Cu substrate was also demonstrated.
Originality/value
It was found that adding approximately 1.5 and 1.0 Wt.% of In and Sb, respectively, in Sn-3.5Ag solder provided the best wetting performance and improved the solder spreadability.
Details
Keywords
Viscosity is an important basic physical property of liquid solders. However, because of the very complex nonlinear relationship between the viscosity of the liquid ternary…
Abstract
Purpose
Viscosity is an important basic physical property of liquid solders. However, because of the very complex nonlinear relationship between the viscosity of the liquid ternary Sn-based lead-free solder and its determinants, a theoretical model for the viscosity of the liquid Sn-based solder alloy has not been proposed. This paper aims to address the viscosity issues that must be considered when developing new lead-free solders.
Design/methodology/approach
A BP neural network model was established to predict the viscosity of the liquid alloy and the predicted values were compared with the corresponding experimental data in the literature data. At the same time, the BP neural network model is compared with the existing theoretical model. In addition, a mathematical model for estimating the melt viscosity of ternary tin-based lead-free solders was constructed using a polynomial fitting method.
Findings
A reasonable BP neural network model was established to predict the melt viscosity of ternary tin-based lead-free solders. The viscosity prediction of the BP neural network agrees well with the experimental results. Compared to the Seetharaman and the Moelwyn–Hughes models, the BP neural network model can predict the viscosity of liquid alloys without the need to calculate the relevant thermodynamic parameters. In addition, a simple equation for estimating the melt viscosity of a ternary tin-based lead-free solder has been proposed.
Originality/value
The study identified nine factors that affect the melt viscosity of ternary tin-based lead-free solders and used these factors as input parameters for BP neural network models. The BP neural network model is more convenient because it does not require the calculation of relevant thermodynamic parameters. In addition, a mathematical model for estimating the viscosity of a ternary Sn-based lead-free solder alloy has been proposed. The overall research shows that the BP neural network model can be well applied to the theoretical study of the viscosity of liquid solder alloys. Using a constructed BP neural network to predict the viscosity of a lead-free solder melt helps to study the liquid physical properties of lead-free solders that are widely used in electronic information.
Details
Keywords
Liang Zhang, Song-bai Xue, Li-li Gao, Yan Chen, Sheng-lin Yu, Zhong Sheng and Guang Zeng
The purpose of this paper is to investigate the effects of minor addition of the rare earth (RE) element cerium, Ce, on the microstructures and creep properties of Sn-Ag-Cu solder…
Abstract
Purpose
The purpose of this paper is to investigate the effects of minor addition of the rare earth (RE) element cerium, Ce, on the microstructures and creep properties of Sn-Ag-Cu solder alloys.
Design/methodology/approach
The pure Sn, Sn-Cu alloy, Sn-Ag alloy and Cu-Ce alloy were used as raw materials. Sn-Ag-Cu alloys with different contents of RE Ce were chosen to compare with Sn-Ag-Cu. The raw materials of Sn, Sn-Cu alloy, Sn-Ag alloy, Cu-Ce alloy were melted in a ceramic crucible, and were melted at 550°C ± 1°C for 40 minutes. To homogenize the solder alloy, mechanical stirring was performed every ten minutes using a glass rod. During the melting, KC1 + LiCI (1.3:1), were used over the surface of liquid solder to prevent oxidation. The melted solder was chill cast into a rod.
Findings
It is found that the microstructure exhibits smaller grains and the Ag3Sn/Cu6Sn5 intermetallic compound (IMC) phases are modified in matrix with the addition of Ce. In particular, the addition of 0.03 wt.% Ce to the Sn-Ag-Cu solder can refine the microstructures and decrease the thickness of the IMC layers of Sn-Ag-Cu solder alloys. Meanwhile, thermodynamic analysis showed that these phenomena could be attributed to the reduction of the driving force for Cu-Sn IMC formation due to the addition of Ce. Results calculated using the thermodynamic method are close to the above experimental data. Thus, the optimum content of Ce in Sn-Ag-Cu solder alloys should be about 0.030 percent. Additionally, the effect of Ce on the creep rupture life of Sn-Ag-Cu soldered joints was studied. It was found that the creep rupture life may be increased up to 7.5 times more than that of the original Sn-Ag-Cu alloy, when Ce accounts for 0.030 percent.
Originality/value
This paper usefully investigates the effects of the RE cerium (Ce), on the microstructures and creep properties of Sn-Ag-Cu solder alloys, optimizing the quantity of Ce in the Sn-Ag-Cu solder alloy through a thermodynamic method and by creep-rupture life testing.
Details
Keywords
Lina Syazwana Kamaruzzaman and Yingxin Goh
This paper aims to review recent reports on mechanical properties of Sn-Bi and Sn-Bi-X solders (where X is an additional alloying element), in terms of the tensile properties…
Abstract
Purpose
This paper aims to review recent reports on mechanical properties of Sn-Bi and Sn-Bi-X solders (where X is an additional alloying element), in terms of the tensile properties, hardness and shear strength. Then, the effects of alloying in Sn-Bi solder are compared in terms of the discussed mechanical properties. The fracture morphologies of tensile shear tested solders are also reviewed to correlate the microstructural changes with mechanical properties of Sn-Bi-X solder alloys.
Design/methodology/approach
A brief introduction on Sn-Bi solder and reasons to enhance the mechanical properties of Sn-Bi solder. The latest reports on Sn-Bi and Sn-Bi-X solders are combined in the form of tables and figures for each section. The presented data are discussed by comparing the testing method, technical setup, specimen dimension and alloying element weight percentage, which affect the mechanical properties of Sn-Bi solder.
Findings
The addition of alloying elements could enhance the tensile properties, hardness and/or shear strength of Sn-Bi solder for low-temperature solder application. Different weight percentage alloying elements affect differently on Sn-Bi solder mechanical properties.
Originality/value
This paper provides a compilation of latest report on tensile properties, hardness, shear strength and deformation of Sn-Bi and Sn-Bi-X solders and the latest trends and in-depth understanding of the effect of alloying elements in Sn-Bi solder mechanical properties.
Details
Keywords
Ervina Efzan Mhd Noor and Amares Singh
The aim of the present study was to gather and review all the important properties of the Sn–Ag–Cu (SAC) solder alloy. The SAC solder alloy has been proposed as the alternative…
Abstract
Purpose
The aim of the present study was to gather and review all the important properties of the Sn–Ag–Cu (SAC) solder alloy. The SAC solder alloy has been proposed as the alternative solder to overcome the environmental concern of lead (Pb) solder. Many researchers have studied the SAC solder alloy and found that the properties such as melting temperature, wettability, microstructure and interfacial, together with mechanical properties, are better for the SAC solder than the tin – lead (SnPb) solders. Meanwhile, addition of various elements and nanoparticles seems to produce enhancement on the prior bulk solder alloy as well. These benefits suggest that the SAC solder alloy could be the next alternative solder for the electronic packaging industry. Although many studies have been conducted for this particular solder alloy, a compilation of all these properties regarding the SAC solder alloy is still not available for a review to say.
Design/methodology/approach
Soldering is identified as the metallurgical joining method in electronic packaging industry which uses filler metal, or well known as the solder, with a melting point < 425°C (Yoon et al., 2009; Ervina and Marini, 2012). The SAC solder has been developed by many methods and even alloying it with some elements to enhance its properties (Law et al., 2006; Tsao et al., 2010; Wang et al., 2002; Gain et al., 2011). The development toward miniaturization, meanwhile, requires much smaller solder joints and fine-pitch interconnections for microelectronic packaging in electronic devices which demand better solder joint reliability of SAC solder Although many studies have been done based on the SAC solder, a review based on the important characteristics and the fundamental factor involving the SAC solder is still not sufficient. Henceforth, this paper resolves in stating all its important properties based on the SAC solder including its alloying of elements and nanoparticles addition for further understanding.
Findings
Various Pb-free solders have been studied and investigated to overcome the health and environmental concern of the SnPb solder. In terms of the melting temperature, the SAC solder seems to possess a high melting temperature of 227°C than the Pb solder SnPb. Here, the melting temperature of this solder falls within the range of the average reflow temperature in the electronic packaging industry and would not really affect the process of connection. A good amendment here is, this melting temperature can actually be reduced by adding some element such as titanium and zinc. The addition of these elements tends to decrease the melting temperature of the SAC solder alloy to about 3°C. Adding nanoparticles, meanwhile, tend to increase the melting temperature slightly; nonetheless, this increment was not seemed to damage other devices due to the very slight increment and no drastic changes in the solidification temperature. Henceforth, this paper reviews all the properties of the Pb-free SAC solder system by how it is developed from overcoming environmental problem to achieving and sustaining as the viable candidate in the electronic packaging industry. The Pb-free SAC solder can be the alternative to all drawbacks that the traditional SnPb solder possesses and also an upcoming new invention for the future needs. Although many studies have been done in this particular solder, not much information is gathered in a review to give better understanding for SAC solder alloy. In that, this paper reviews and gathers the importance of this SAC solder in the electronic packaging industry and provides information for better knowledge.
Originality/value
This paper resolves in stating of all its important properties based on the SAC solder including its alloying of elements and nanoparticles addition for further understanding.
Details
Keywords
Dhafer Abdul Ameer Shnawah, Suhana Binti Mohd Said, Mohd Faizul Bin Mohd Sabri, Irfan Anjum Badruddin and Fa Xing Che
The purpose of this paper is to investigate the effects of small additions (0.1 and 0.3 wt%) of Fe on the bulk alloy microstructure and tensile properties of low Ag‐content…
Abstract
Purpose
The purpose of this paper is to investigate the effects of small additions (0.1 and 0.3 wt%) of Fe on the bulk alloy microstructure and tensile properties of low Ag‐content Sn‐1Ag‐0.5Cu lead‐free solder alloy.
Design/methodology/approach
Sn‐1Ag‐0.5Cu, Sn‐3Ag‐0.5Cu and Sn‐1Ag‐0.5Cu containing 1 and 3 wt.% Fe solder specimens were prepared by melting pure ingots of Sn, Ag, Cu and Fe in an induction furnace and subsequently remelting and casting to form flat dog‐bone shaped specimens for tensile testing. The solder specimens were subjected to tensile testing using an INSTRON tester with a loading rate 10‐3 s‐1. To obtain the microstructure, the solder samples were prepared by dicing, molding, grinding and polishing processes. The microstructural analysis was carried out using scanning electron microscopy/Energy Dispersive X‐ray spectroscopy. Electron backscatter diffraction (EBSD) analysis was used to identify the IMC phases.
Findings
In addition to large primary β‐Sn grains, the addition of Fe to the SAC105 alloy formed large circular shaped FeSn2 IMC particles located in the eutectic regions. This had a significant effect in reducing the elastic modulus and yield strength and maintaining the elongation at the SAC105 level. Moreover, the additions of Fe resulted in the inclusion of Fe in the Ag3Sn and Cu6Sn5 IMC particles. The additions of Fe did not have any significant effect on the melting behaviour.
Research limitations/implications
The paper provides a starting‐point for studying the effect of minor additions of Fe on the drop impact and thermal cycling reliability of SAC105 alloy considering the bulk alloy microstructure and tensile properties. Further investigations should be undertaken in the future.
Originality/value
The effect of Fe addition on the bulk alloy microstructure and tensile properties of the SAC105 alloy has been studied for the first time. Fe‐containing SAC105 alloy may have the potential to increase the drop impact and thermal cycling reliability compared with the standard SAC105 alloy.
Details