Search results

This paper aims to investigate voiding phenomena in solder joints under thermal pads of light-emitting diodes (LEDs) assembled in mass production environment by reflow soldering by using seven low-voiding lead-free solder pastes.

The solder pastes investigated are of SAC305 type, Innolot type or they are especially formulated by the manufacturers on the base of (SnAgCu) alloys with addition of some alloying elements such as Bi, In, Sb and Ti to provide low-void contents. The SnPb solder paste – OM5100 – was used as a benchmark. The solder paste coverage of LED solder pads was chosen as a measure of void contents in solder joints because of common usage of this parameter in industry practice.

It was found that the highest coverage and, related to it, the least void contents are in solder joints formed with the pastes LMPA-Q and REL61, which are characterized by the coverage of mean value 93.13% [standard deviation (SD) = 2.72%] and 92.93% (SD = 2.77%), respectively. The void diameters reach the mean value equal to 0.061 mm (SD = 0.044 mm) for LMPA-Q and 0.074 mm (SD = 0.052 mm) for REL61. The results are presented in the form of histograms, plot boxes and X-ray images. Some selected solder joints were observed with 3D computer tomography.

The statistical analyses are carried out on the basis of 2D X-ray images with using Origin software. They enable to compare features of various solder pastes recommended by manufacturers as low voiding. The results might be useful for solder paste manufacturers or electronic manufacturing services.

The Kirkendall void had been a well-known issue for long-term reliability of semiconductor interconnects; while even the KVs exist at the interfaces of Cu and Sn, it may still be able to pass the condition of unbias long-term reliability testing, especially for 2,000 cycles of temperature cycling test and 2,000 h of high temperature storage. A large number of KVs were observed after 200 cycles of temperature cycling test at the intermetallic Cu₃Sn layer which locate between the intermetallic Cu₆Sn₅ and Cu layers. These kinds of voids will grow proportional with the aging time at the initial stage. This paper aims to compare various IMC thickness as a function of stress test, the Cu₃Sn and Cu₆Sn₅ do affected seriously by heat, but Ni₃Sn₄ is not affected by heat or moisture.

The package is the design in the flip chip-chip scale package with bumping process and assembly. The package was put in reliability stress test that followed AEC-Q100 automotive criteria and recorded the IMC growing morphology.

The Cu₆Sn₅ intermetallic compound is the most sensitive to continuous heat which grows from 3 to 10 µm at high temperature storage 2,000 h testing, and the second is Cu₃Sn IMC. Cu₆Sn₅ IMC will convert to Cu₃Sn IMC at initial stage, and then Kirkendall void will be found at the interface of Cu and Cu₃Sn IMC, which has quality concerning issue if the void’s density grows up. The first phase to form and grow into observable thickness for Ni and lead-free interface is Ni₃Sn₄ IMC, and the thickness has little relationship to the environmental stress, as no IMC thickness variation between TCT, uHAST and HTSL stress test. The more the Sn exists, the thicker Ni₃Sn₄ IMC will be derived from this experimental finding compare the Cu/Ni/SnAg cell and Ni/SnAg cell.

The research found that FCCSP can pass automotive criteria that follow AEC-Q100, which give the confidence for upgrading the package type with higher efficiency and complexities of the pin design.

This result will impact to the future automotive package, how to choose the best package methodology and what is the way to do the package. The authors can understand the tolerance for the kind of flip chip package, and the bump structure is then applied for high-end technology.

The overall three kinds of bump structures, Cu/Ni/SnAg, Cu/SnAg and Ni/SnAg, were taken into consideration, and the IMC growing morphology had been recorded. Also, the IMC had changed during the environmental stress, and KV formation was reserved.

The purpose of this paper is to develop and test the thermal interface materials (TIM) for application in assembly of semiconductor chips to package. Good adhesion properties (>5 MPa shear strength) and low thermal interface resistance (better than for SAC solders) are the goal of this research.

Mechanical and thermal properties of TIM joints between gold plated contacts of chip and substrate were investigated. Sintering technique based on Ag pastes was applied for purpose of this study. Performance properties were assessed by shear force tests and thermal measurements. Scanning electron microscopy was used for microstructural observations of cross-section of formed joints.

It was concluded that the best properties are achieved for pastes containing spherical Ag particles of dozens of micrometer size with flake shaped Ag particles of few micrometers size. Sintering temperature at 230°C and application of 1 MPa force on the chip during sintering gave the higher adhesion and the lowest thermal interface resistance.

The new material based on Ag paste containing mixtures of Ag particles of different size (form nanometer to dozens of microns) and shape (spherical, flake) suspended in resin was proposed. Joints prepared using sintering technique and Ag pastes at 230°C with applied pressure shows better mechanical and thermal than other TIM materials such as thermal grease, thermal gel or thermally conductive adhesive. Those material could enable electronic device operation at temperatures above 200°C, currently unavailable for Si-based power electronics.

This paper aims to perform thermal and mechanical characterization for silver-based sintered thermal joints. Layer quality affects thermal and mechanical performance, and it is important to achieve information about how materials and process parameters influence them.

Thermal investigation of the thermal joints analysis method was focused on determination of thermal resistance, where temperature measurements were performed using infrared camera. They were performed in two modes: steady-state analysis and dynamic analysis. Mechanical analysis based on measurements of mechanical shear force. Additional characterizations based on X-ray image analysis (image thresholding), optical microscope of polished cross-section and scanning electron microscope image analysis were proposed.

Sample surface modification affects thermal resistance. Silver metallization exhibits the lowest thermal resistance and the highest mechanical strength compared to the pure Si surface. The type of dynamic analysis affects the results of the thermal resistance.

Investigation of the layer quality influence on mechanical and thermal performance provided information about different joint types.

Solar cells could make textile-based wearable systems energy independent without the need for battery replacement or recharging; however, their laundry resistance, which is prerequisite for the product acceptance of e-textiles, has been rarely examined. This paper aims to report a systematic study of the laundry durability of solar cells embedded in textiles.

This research included small commercial monocrystalline silicon solar cells which were encapsulated with functional synthetic textile materials using an industrially relevant textile lamination process and found them to reliably endure laundry washing (ISO 6330:2012). The energy harvesting capability of eight textile laminated solar cells was measured after 10–50 cycles of laundry at 40 °C and compared with light transmittance spectroscopy and visual inspection.

Five of the eight textile solar cell samples fully maintained their efficiency over the 50 laundry cycles, whereas the other three showed a 20%–27% decrease. The cells did not cause any visual damage to the fabric. The result indicates that the textile encapsulated solar cell module provides sufficient protection for the solar cells against water, washing agents and mechanical stress to endure repetitive domestic laundry.

This study used rigid monocrystalline silicon solar cells. Flexible amorphous silicon cells were excluded because of low durability in preliminary tests. Other types of solar cells were not tested.

A review of literature reveals the tendency of researchers to avoid standardized textile washing resistance testing. This study removes the most critical obstacle of textile integrated solar energy harvesting, the washing resistance.

This paper aims to present the application of a tailored systematic engineering design procedure to the concept design of a small production plant for compostable packaging made by straw fibres and bioplastic. In particular, the obtained boxes are intended to be used for wine bottles.

A systematic procedure has been adopted, which underpins on a comprehensive analysis of the design requirements and the function modelling of the process. By considering well-known models of the engineering design process, the work focuses on the early design stages that precede the embodiment design of the whole components of the plant.

The followed design approach allowed to preliminarily evaluate different alternatives of the process from a functional point of view, thus allowing to identify the preferred conceptual process solution. Based on the identified functional sequence, a first evaluation of the potential productivity and the required human resources has been performed.

The procedure shown in this work has been applied only for the considered case of compostable packaging, and other applications are needed to optimize it. Nevertheless, the adopted systematic approach can be adapted for any context where it is necessary to conceive a new production plant for artefacts made by innovative materials.

The work presented in this paper represents one of the few practical examples available in the literature where systematic conceptual design procedures are presented. More specifically, to the best of the authors’ knowledge, this is the very first application of systematic design methods to compostable packaging production.

This study aims to examine the metal pollution in coastal sediment in the Peninsular Malaysia.

Approximately 141 published studies were screened from 1,285 documents and reviewed to determine the existing pollution status in the coastal areas of Peninsular Malaysia and the metals under review were Pb, Hg, Cd, Ar, Cu, Zn, Cr and Ni. Sources of pollutants and their effect on biological systems, marine organisms and human health were addressed in this review as well as recommendation of heavy metal removal or remedies in short. Emphasis is placed on marine pollution, particularly on the toxic metal accumulation in biota.

This study has revealed the different concentrations of pollutants, low, moderately, and chronically contaminated areas from heavy metals and the consequences to aquatic ecosystem and indirectly to human health, since an increasing in the coastal developments in Peninsular Malaysia.

This study has revealed the different concentrations of pollutants, low, moderately, and chronically contaminated areas from heavy metals and the consequences to aquatic ecosystem and indirectly to human health, since an increasing in the coastal developments in Peninsular Malaysia.

This paper aims to develop thermal analysis method of thermal joints characterization. The impact on convection on thermal resistance analysis with use thermography for silver-based thermal joints were investigated for non-metallized and metalized semiconductor surfaces. Heat transfer efficiency depends on thermal conductivity; radiation was used to perform thermographic analysis; the convection is energy loss, so its removing might improve measurements accuracy.

Investigation of thermal joints analysis method was focused on determination of convection impact on thermal resistance thermographic analysis method. Measuring samples placed in vacuum chamber with lowered pressure requires transparent window for infrared radiation that is used for thermographic analysis. Impact of infrared window and convection on temperature measurements and thermal resistance were referred.

The results showed that the silicon window allowed to perform thermal analysis through, and the convection was heat transfer mode which create 15% energy loss.

It is possible to measure thermal resistance for silver-based thermal joints with convection eliminated to improve measurements accuracy.

This paper aims to raise awareness of a potential planning pitfall and provide recommendations on how to assess and improve upon current practices. In potential conflict areas, such as the Korean Theater of Operations (KTO), military forces are required to store a portion of their ammunition combat load within depots and ammunition supply points under the control of a servicing ammunition company. This necessitates a lengthy retrieval process, as the ammunition company does not have enough resources to serve all customers simultaneously.

The stored combat load (SCL) retrieval process is modeled as a parallel machine scheduling problem and simulated using synthetic requirements. The current system of retrieval is contrasted against a proposed alternate system through a series of simulations scaled across three factors: number of ammunition company Soldiers, number of customer units and number of magazines.

The proposed alternate system demonstrates a significant potential for reducing the makespan of the SCL retrieval process when more than half of the magazines store SCL for multiple customers and there are more than five customers per Soldier.

Transitioning military units from a peacetime standing to full combat readiness as quickly as possible is of immense value within the KTO and other hostile areas with established troops not actively engaged in combat.

Cables are ubiquitous in electronic-based systems. Electromagnetic emission of cables and crosstalk between wires is an important issue in electromagnetic compatibility and is to be minimized in the design phase. To facilitate the design, models of different complexity and accuracy, for instance, circuit models or finite element (FE) simulations, are used. The purpose of this study is to compare transmission line parameters obtained by measurements and simulations.

Transmission line parameters were determined by means of measurements in the frequency and time domain and by FE simulations in the frequency domain and compared. Finally, a Spice simulation with lumped elements was performed.

The determination of the effective permittivity of insulated wires seems to be a key issue in comparing measurements and simulations.

A space decomposition technique for a guided wave on an infinite configuration with constant cross-section has been introduced, where an analytic representation in the direction of propagation is used, and the transversal fields are approximated by FEs.