Search results

Commercial buildings, which include office buildings, are one of the three major energy-consuming sectors, alongside industrial and transportation sectors. The vast increase in the number of buildings is a positive sign of the rapid development of Malaysia. However, most Malaysian government office buildings tend to consume energy inefficiently due to lack of energy optimization. Most of the previous studies focused on the performance of green buildings in fulfilling the green development guidelines. As such, it is essential to study the energy performance of existing government office buildings that were constructed before most energy-efficient standards were implemented to mitigate energy wastage due to the lack of energy optimization. This study aims to analyse the energy performance of existing non-green Malaysian government office buildings and the factors that influence building energy consumption, as well as to evaluate the efficacy of the existing energy conservation measures.

This study was conducted by a literature review and case study. The chosen buildings are six government office building blocks located in Kuala Lumpur, the capital city of Malaysia. In this study, a literature review has been conducted on the common factors affecting energy consumption in office buildings. The energy consumption data of the buildings were collected to calculate the building energy intensity (BEI). The BEI was compared to the MS1525:2019 and GBI benchmarks to evaluate energy performance. SketchUp software was utilized to illustrate the solar radiation and sun path diagram of the case study buildings. Finally, recommendations were derived for retrofit strategies based on non-design factors and passive design factors.

In typical government office buildings, the air-conditioning system consumed the most energy at 65.5%, followed by lighting system at 22.6%, and the remaining 11.9% was contributed by office appliances. The energy performance of the case study buildings is considered as satisfactory as the BEI did not exceed the MS1525:2019 benchmark of 200 kWh/m2/year. The E Block recorded the highest BEI of 183.12 kWh/m2/year in 2020 due to its north-east orientation which is exposed to the most solar radiation. Besides, E Block consists of rooms that can accommodate large number of occupants. As such, non-design factors which include higher occupancy rate and higher cooling demand due to high outdoor temperature leads to higher energy consumption. By considering passive design features such as building orientation and building envelope thermal properties, energy consumption can be reduced significantly.

This study provided a comprehensive insight into the energy performance of Malaysian government office buildings, which were constructed before the energy-efficient standards being introduced. By calculating the BEI of six government office buildings, it is found that the energy performance of the case study buildings fulfils the MS1525 benchmark, and that all their BEIs are below 200 kWh/m2/year. Malaysia's hot and humid climate significantly affects a building's cooling load, and it is found the air-conditioning system is the major energy consumer of Malaysian government office buildings. This study discusses the efficacy of the energy-saving measures implemented in the case study buildings to optimize energy consumption. Recommendations were derived based on the non-design factors and passive design factors that affected the energy consumption of the case study building. It is envisioned that this study can provide practical strategies for retrofit interventions to reduce energy consumption in Malaysian office buildings as well as for office buildings that are in a similar climate.

In this chapter the potential to use water-based Trombe walls to provide heated water for building applications during the summer months is investigated. Design Builder software is used to model a simple single-story building with a south-facing Trombe wall. The effects of using different thermal storage mediums within the Trombe wall on building heating loads during the winter and building cooling loads during the summer are modeled. The amount of thermal energy stored and temperature of water within the thermal storage medium during hot weather conditions were also simulated. On a sunny day on Toronto, Canada, the average temperature of the water in a Trombe wall integrated into a single-story building can reach ∼57°C, which is high enough to provide for the main hot water usages in buildings. Furthermore, the amount of water heated is three times greater than that required in an average household in Canada. The results from this work suggest that water-based Trombe walls have great potential to enhance the flexibility and utility of Trombe walls by providing heated water for building applications during summer months, without compromising performance during winter months.

The aim is to holistically assess the environmental performance of windows and analyse how their design and characteristics contribute to the overall performance of the building/space. This study focuses on the performance of windows in patient rooms hosting less mobile people.

This study investigates the life cycle environmental impacts of different glazing types, window frames and fire safety doors at the product level. This article also presents a building-integrated environmental analysis of patient rooms that considers the multiple functionalities of windows by incorporating dynamic energy analysis, comfort and daylighting performance with a life cycle assessment (LCA) study.

The results indicate that the amount of flat glass is the main contributor to the environmental impacts of the glazing units. As for the patient rooms, global warming shows the most significant contribution to the environmental costs, followed by human toxicity, particulate matter formation and eutrophication. The key drivers for these impacts are production processes and operational energy use. This study highlights the significance of evaluating a wide range of criteria for assessing the performance of windows.

An integrated assessment approach is used to investigate the influence of windows on environmental performance by considering the link between window/design parameters and their effects on energy use/costs, daylighting, comfort and environmental impacts. The embodied impacts of different building elements and the influence of various design parameters on environmental performance are assessed and compared. The environmental costs are expressed as an external environmental cost (euro).

The learning outcomes of this study are to identify and discuss ways in which energy consumption in a residential educational institute can be reduced by improving demand-side energy management for sustainable development; summarise the challenges that an institute faces in transitioning to a more environmentally friendly mode of operations concerning energy management; illustrate the difference between operating expense and capital expenditure methods used for solar rooftop projects from the perspective of Goa Institute of Management (GIM); and analyse different project proposals for solar rooftop power generation energy using capital budgeting techniques.

Dr Ajit Parulekar, director at GIM, was evaluating the steps taken over the past few years for sustainable energy management to understand their impact and consider ways in which to take the environmental sustainability agenda forward. One of the projects that he was considering was the rooftop solar power plant. GIM had received proposals from several different vendors and evaluated three proposals out of these. He needed to decide on the capacity of the rooftop solar power generation and the type of contract that he should get into for the implementation of the project. This case study describes the differences and highlights the advantages and disadvantages of all the mentioned models with respect to GIM.

This case study is suitable for post-graduate level management students, as well as for undergraduate-level finance and management students.

Teaching notes are available for educators only.

CSS4: Environmental management.

This paper investigates the optimization of window design factors (WDFs) in hospital buildings, particularly in government hospitals within the arid climate of the Qassim region, with the aim of achieving a better cooling load reduction. Continuous monitoring of the hospital ward section is crucial due to patients' needs, requiring optimal indoor air quality and cooling load.

The study identifies the optimal conditions for WDF design to mitigate cooling load, including window-to-wall ratio (WWR), window orientation (WO), room size and U-value (thermal properties), effectively reduce energy consumption in terms of sensible cooling load (MWh/m2) and comply with local codes. Data collection involved a smart weather station, while the Integrated Environmental Solution Virtual Environment (IESVE) software facilitated the simulation process.

Key findings reveal that larger patient rooms were about 40% more energy-efficient than smaller rooms. The northern orientation showed lower energy consumption, and specific WWRs and glazing U-values significantly affected energy loads. In an analysis of U-value changes in energy performance based on the Saudi Building Code (SBC), the presented values did not meet the minimum energy consumption standards. For a valid 40% WWR with a thermal permeability of 2.89, 0.181 MWh/m2 was consumed, while for an invalid 100% WWR with the same permeability but facing the north, 0.156 MWh/m2 was consumed, which is considered an invalid practice. It is vital to follow prescribed standards to ensure energy efficiency and avoid unnecessary costs.

Focus lies in emphasizing the significance of adhering to prescribed standards, such as SBC, to guarantee energy efficiency and prevent unwarranted expenses. Additionally, the authors highlight the crucial role of optimizing glazing properties and allocating the WWR appropriately to achieve energy-efficient building design, accounting for diverse orientations and climatic conditions.

The purpose of this paper is to introduce flexible dye-sensitized solar cells (FDSSCs).

In the third generation solar cells, glass was used as a substrate, which due to its high weight and fragility, was not possible to produce continuously. However, in flexible solar cells, flexible substrates are used as new technology. The most important thing may choose a suitable substrate to produce a photovoltaic (PV) device with optimal efficiency.

Conductive plastics or metallic foils are the two main candidates for glass replacement, each with its advantages and disadvantages. As some high-temperature methods are used to prepare solar cells, metal substrates can be used to prepare PV devices without any problems. In contrast to the advantage of high thermal resistance in metals, metal substrates are dark and do not transmit enough light. In other words, metal substrates have a high loss of photon energy. Like all technologies, PV devices with polymer substrates have technical disadvantages.

In this study, the development of FDSSCs offers improved photovoltaic properties.

The most important challenge is the poor thermal stability of polymers compared to glass and metal, which requires special methods to prepare polymer solar cells. The second important point is choosing the suitable components and materials for this purpose.

Dependence of efficiency and performance of the device on the angle of sunlight, high-cost preparation devices components, limitations of functional materials such as organic-mineral sensitizers, lack of close connection between practical achievements and theoretical results and complicated fabrication process and high weight.

Window shading has always been an effective technique to control the access of solar radiation; however, inappropriate selection of the shading technique, location and optical properties may lead to an increase in energy consumed for cooling and artificial lighting. Venetian blinds (VBs) are a type of adjustable shading devices that can be installed to the interior, exterior or in between glass panes of a window and that can be easily implemented in both new and existing buildings. This study aims to investigate the impact of three VB parameters: slat angle, reflectivity and location on the overall energy consumption of a residential space with a south-facing facade under the hot arid desert climate of Saudi Arabia’s capital, Riyadh. For the purpose of globalizing the findings, the same investigations were applied for two other cities of similar climates: Cairo, Egypt, and Arizona, the USA.

A test room was modelled for energy simulation, with a 20% window-to-wall ratio. A VB was assigned with alternatives of being located to the indoor, outdoor or in between double glass panes. High, medium and low reflectivity values were applied at each location at slat angle alternatives of 15°, 30°, 45°, 60°, 75° and 90°.

Results showed VB performance across slat angles, where up to 20.1% energy savings were achieved by mid-pane high reflectivity VBs in Riyadh, while the value exceeded 30% in case of being externally located. A similar performance pattern occurred in the other two cities of hot arid desert climates: Cairo and Arizona.

The study is limited to VBs at a fixed position, with no upward movement for partial or full openness conditions. The effect of blind control and operation on performance, such as the amount and duration of openness/closure of the blind and changes in slat angle across time, in addition to VB automation, shall be investigated in a future study.

The better understanding of VB energy performance achieved would enhance a more rational selection of VBs, which would benefit the construction industry as it would assist designers, real estate developer companies, as well as end-users in the decision-making process and help to realize energy-efficient solutions in residential buildings. VB production entities would also benefit by manufacturing and promoting for energy-efficient products.

In this study, a matrix of combinations of three VB parameters was developed, and the effect of these combinations on the overall energy consumption of both artificial lighting and heating, ventilation and air conditioning (HVAC) systems was evaluated and compared to identify the combinations of higher efficiency. The literature showed that these three parameters were hardly investigated in a combined form and hardly assessed by considering the overall energy consumed by both artificial lighting and HVAC.

Electric motor heating during biomass recovery and its handling on conveyor is a serious concern for the motor performance. Thus, the purpose of this paper is to design and develop a hardware prototype of master–slave electric motors based biomass conveyor system to use the motors under normal operating conditions without overheating.

The hardware prototype of the system used master–slave electric motors for embedded controller operated robotic arm to automatically replace conveyor motors by one another. A mixed signal based embedded controller (C8051F226DK), fully compliant with IEEE 1149.1 specifications, was used to operate the entire system. A precise temperature measurement of motor with the help of negative temperature coefficient sensor was possible due to the utilization of industry standard temperature controller (N76E003AT20). Also, a pulse width modulation based speed control was achieved for master–slave motors of biomass conveyor.

As compared to conventional energy based mains supply, the system is self-sufficient to extract more energy from solar supply with an energy increase of 11.38%. With respect to conventional energy based \ of 47.31%, solar energy based higher energy saving of 52.69% was reported. Also, the work achieved higher temperature reduction of 34.26% of the motor as compared to previous cooling options.

The proposed technique is free from air, liquid and phase-changing material based cooling materials. As a consequence, the work prevents the wastage of these materials and does not cause the risk of health hazards. Also, the motors are used with their original dimensions without facing any leakage problems.