Search results

Discusses the 27 papers in ISEF 1999 Proceedings on the subject of electromagnetisms. States the groups of papers cover such subjects within the discipline as: induction machines; reluctance motors; PM motors; transformers and reactors; and special problems and applications. Debates all of these in great detail and itemizes each with greater in‐depth discussion of the various technical applications and areas. Concludes that the recommendations made should be adhered to.

The purpose of this paper is to propose a miniaturized tri-band bandstop filter that finds application in a modern dense communication system where size and multi-band plays a vital role.

In this paper, the authors propose a miniaturized tri-band microstrip bandstop filter which combines the conventional bandstop filter and spur microstrip line structures such that this design achieves tri-band operation at 1.8 GHz and 3 GHz. The overall length of the microstrip filter is found to reduce from 126 to 45 mm because of introduction of spur lines and via-hole grounding. The addition of spur lines replaces two resonators, introduces two additional resonant frequencies and enhances the −6 dB bandwidth of the center frequency by 14 %.The addition of via-holes in each resonator reduces its length into half of its original length, thereby reducing filter size.

Resonance occurs at three different frequencies 1.8, 2.4 and 3 GHz. The filter size reduces from 126 to 45 mm, and the −6 dB rejection bandwidth of center frequency improves by 14 %.

The overall filter size is reduced by 65% and it resonates at three different frequencies 1.8, 2.4 and 3 GHz with an improved bandwidth of 10 % around the center frequency.

This paper aims to introduce a new novel microstrip monopulse comparator system to reduce the spurious radiation from the comparator and the feed network for achieving better radiation performance.

Two substrate layers have been used for the microstrip monopulse comparator system. The feed network and the comparator circuits are on the first substrate layer and the microstrip array antenna is on the second layer. The elements of the array antenna are novel square four-sided narrow rectangular slot antennas built on a conducting plane. A commercially available computational software, CST microwave studio, has been used for the analysis of the system.

Two substrate layers have been used for the microstrip monopulse comparator system. The feed network and the comparator circuits are on the first substrate layer and the microstrip array antenna is on the second layer. The elements of the array antenna are novel square four-sided narrow rectangular slot antennas built on a conducting plane. A commercially available computational software, CST microwave studio, has been used for the analysis of the system.

The system is proposed for tracking moving targets.

Novel slot radiators are introduced as radiating elements in this paper. The antenna arrangement shields the comparator and the feed network circuits, reducing the spurious radiation significantly.

The paper aims to focus on implantable antenna sensors used for biomedical applications. Communication in implantable medical devices (IMDs) is beneficial for continuous monitoring of health. The ability to communicate with exterior equipment is an important aspect of IMD. Thus, the design of an implantable antenna for integration into IMD is important.

In this review, recent developments in IMDs, three types of antenna sensors, which are recommended by researchers for biomedical implants are considered. In this review, design requirements, different types of their antenna, parameters and characteristics in medical implants communication system (MICS) and industrial, scientific and medical (ISM) bands are summarized here. Also, overall current progress in development of implantable antenna sensor, its challenges and the importance of human body characteristics are described.

This article give information about the requirements of implantable antenna sensor designs, types of antennas useful to design implantable devices and their characteristics in MICS and ISM bands. Recent advancement in implantable devices has led to an improvement in human health.

The paper provides useful information on implantable antennas design for biomedical application. The designing of such antennas needs to meet requirements such as compact size, patients’ safety, communication ability and biocompatibility.

This paper aims to present the design development and measurement of two aerodynamic slotted X-bands back-to-back planer substrate-integrated rectangular waveguide (SIRWG/SIW) to Microstrip (MS) line transition for satellite and RADAR applications. It facilitates the realization of nonplanar (waveguide-based) circuits into planar form for easy integration with other planar (microstrip) devices, circuits and systems. This paper describes the design of a SIW to microstrip transition. The transition is broadband covering the frequency range of 8–12 GHz. The design and interconnection of microwave components like filters, power dividers, resonators, satellite dishes, sensors, transmitters and transponders are further aided by these transitions. A common planar interconnect is designed with better reflection coefficient/return loss (RL) (S₁₁/S₂₂ ≤ 10 dB), transmission coefficient/insertion loss (IL) (S₁₂/S₂₁: 0–3.0 dB) and ultra-wideband bandwidth on low profile FR-4 substrate for X-band and Ku-band functioning to interconnect modern era MIC/MMIC circuits, components and devices.

Two series of metal via (6 via/row) have been used so that all surface current and electric field vectors are confined within the metallic via-wall in SIW length. Introduced aerodynamic slots in tapered portions achieve excellent impedance matching and tapered junctions with SIW are mitered for fine tuning to achieve minimum reflections and improved transmissions at X-band center frequency.

Using this method, the measured IL and RLs are found in concord with simulated results in full X-band (8.22–12.4 GHz). RLC T-equivalent and p-equivalent electrical circuits of the proposed design are presented at the end.

The measurement of the prototype has been carried out by an available low-cost X-band microwave bench and with a Keysight E4416A power meter in the microwave laboratory.

The transition is fabricated on FR-4 substrate with compact size 14 mm × 21.35 mm × 1.6 mm and hence economical with IL lie within limits 0.6–1 dB and RL is lower than −10 dB in bandwidth 7.05–17.10 GHz. Because of such outstanding fractional bandwidth (FBW: 100.5%), the transition could also be useful for Ku-band with IL close to 1.6 dB.

The purpose of this paper is to present the design of a compact microstrip bandpass filter (BPF) in dual-mode configuration loaded with cross-loop and square ring slots on a square patch resonator for C-band applications.

In the proposed design, the dual-mode response for the filter is realized with two transmission zeros (TZs) by the insertion of a perturbation element at the diagonal corner of the square patch resonator with orthogonal feed lines. Such TZs at the edges of the passband result in better selectivity for the proposed BPF. Moreover, the cross-loop and square ring slots are etched on a square patch resonator to obtain a miniaturized BPF.

The proposed dual-mode microstrip filter fabricated in RT/duroid 6010 substrate using PCB technology has a measured minimum insertion loss of 1.8 dB and return loss better than 24.5 dB with a fractional bandwidth (FBW) of 6.9%. A compact size of 7.35 × 7.35 mm² is achieved for the slotted patch resonator-based dual-mode BPF at the center frequency of 4.76 GHz. As compared with the conventional square patch resonator, a size reduction of 61% is achieved with the proposed slotted design. The feasibility of the filter design is confirmed by the good agreement between the measured and simulated responses. The performance of the proposed filter structure is compared with other dual-mode filter works.

In the proposed work, a compact dual-mode BPF is reported with slotted structures. The conventional square patch resonator is deployed with cross-loop and square ring slots to design a dual-mode filter with a square perturbation element at its diagonal corner. The proposed filter exhibits compact size and favorable performance compared to other dual-mode filter works reported in literature. The aforementioned design of the dual-mode BPF at 4.76 GHz is suitable for applications in the lower part of the C-band.

The purpose of this paper is to design and construct an amplitude shift keying (ASK) modulator, which, using the digital binary modulating signal, controls a floating memristor emulator (MR) internally without the need for additional control circuits to achieve the ASK modulated wave.

A binary digital unipolar signal to be modulated is converted by a pre-processor circuit into a suitable bipolar modulating direct current (DC) signal for the control of the MR state, using current conveyors the carrier signal’s amplitude is varied with the change in the memristance of the floating MR. A high pass filter is then used to remove the DC control signal (modulating signal) leaving only the modulated carrier signal.

The results from the experiment and simulation are in agreement showed that the MR can be switched between two states and that a change in the carrier signals amplitude can be achieved by using an MR. Thus, showing that the circuit behavior is in line with the proposed theory and validating the said theory.

In this paper, the binary signal to be modulated is modified into a suitable control signal for the MR, thus the MR relies on the internal operation of the modulator circuit for the control of its memristance. An ASK modulation can then be achieved using a floating memristor without the need for additional circuits or signals to control its memristance.

The purpose of this paper is to study and calculate the electrical characteristic of an equilateral triangular microstrip patch antenna that is proposed for dual frequency operation using the pin diode. The electrical characteristic of an equilateral triangular microstrip patch antenna is proposed for dual-frequency operation. Spur lines and ON/OFF condition of the pin diode are utilized to switch the resonant frequency of the patch. The presence of spur lines excites the surface current of the patch which is dependent on the resonant frequency of an equilateral triangular microstrip patch. Insertion of the diode in the spur lines gives a better result and compactness in patch design, which improves the miniaturization in size of patch.

Antenna Design Aspects: A basic structure of an equilateral triangular microstrip antenna (ETMA) having two spur lines and one pin diode positioned in between the spur line is considered in this paper. The design parameters are chosen on the basis of substrate materials having relative permittivity less than three. Specification of the antenna is given in Table I. Substrate material used is RT Duroid 5,880; relative permittivity of the substrate er is 2.2; thickness of dielectric substrate h is 1.5 mm; sides of equilateral triangular patch a are 10 mm, spur width s is 0.5 mm; and spur length b is 2.0 mm.

This paper gives an account of achieving polarization swiftness with coplanar waveguide (CPW) feed. The miniaturized size of the antenna is 35 × 30 mm2. Switchable microstrip equilateral triangular antenna has been demonstrated for dual-frequency operations. The resonant frequency of an ETMA can be adjusted by setting the diode in an ON and OFF state. The design improves the miniaturization in size with a discussion of radiation density. The excited patch surface current is limited to flow around just the mid of the patch in simple ETMA with a single slit cut. It is observed that for an ETMA, when the diode is in the ON state at 9.16 GHz, the excited patch surface current is highly distributed in the patch compared to when the diode is in the ON state at 11 GHz. Similarly, it is observed that the excited surface patch current is highly distributed when the diode is in the OFF state in both frequencies (9 and 11.96 GHz). The mode is changed by the use of a switch at time and it is suitable for wireless communication applications.

Spur lines and the ON/OFF condition of the pin diode are utilized to switch the resonant frequency of the patch. The presence of spur lines excites the surface current of the patch which is dependent on the resonant frequency of an equilateral triangular microstrip patch. Insertion of the diode in spur lines gives a better result and compactness in patch design, which improves the miniaturization in size of the patch.

The design, fabrication and experimental validation of defected microstrip structure (DMS) are proposed to address the problem of near-end crosstalk (NEXT) and far-end crosstalk (FEXT) between the microstrip transmission lines in a printed circuit board.

The proposed DMS evolved with the combination of spur line (L-shaped DMS) and U-shaped DMS topologies. This technique reduces the strength of electromagnetic coupling and suppresses crosstalk by optimizing the capacitive and inductive coupling ratio between the linked microstrip lines. The practical inductance value is much more significant in DMS than in defected ground structures (DGS), but the capacitance value remains the same.

A DMS unit is etched on the aggressor microstrip line instead of the DGS circuit. Because there is no leakage via the ground plane and the circuit size is far smaller than with DGS, the enclosure issue is disregarded. DMS structures have a larger effective inductance and are resistant to electromagnetic interference. A tightly coupled transmission line structure with minimal separation between the coupled microstrip line is designed using DMS. Further research must be conducted to improve the NEXT, FEXT and spacing between the transmission lines.

Simulation and actual measurement results show that the proposed DMS structure can effectively suppress crosstalk by analysing the S-parameters, namely, S_12, S_13 and S_14, with measured values of 1.48 dB, 20.65 dB and 21.099 dB, respectively. The data rate is measured to be 1.34 Gbps as per the eye diagram characterization. The results show that the NEXT and FEXT are reduced by approximately 20 dB in the frequency range of 1–11 GHz for mixed signals. The substantial measured results in the vector network analyser coincide with the computer simulation technology microwave studio suite simulation results.

As a common transmission line, the microstrip line plays an important role in high-speed circuits. The purpose of this paper was to investigate the effects of the circuit design of microstrip lines on the signal integrity (SI). In addition, the influence of the type and thickness of the solder resist ink on SI was analyzed to provide guidance for the related producing process design of printed circuit boards (PCBs).

Microstrip line properties consisting of shape, line-width/line-space ratio, reference layer design and as-covered solder resist ink were designed to measure the insertion loss (S₂₁) in high-speed PCB.

The study showed that the insertion loss (S₂₁) of straight, meander, snake-shaped and wavy microstrip lines was approximately consistent. A microstrip line with width/space ratio less than 0.96 is necessary, as the differential line closing produces a mutual interference. Reference layer including the discontinuous area should be repaired by adjusting the microstrip line parameters. With regard to the solder resist ink, the insertion loss of novel solder resist ink decreased by 0.163 dB/in at 12.9 GHz and 0.164 dB/in at 14 GHz, compared with traditional solder resist ink. Accordingly, the insertion loss effectively improved at a lower thickness of solder resist.

This paper demonstrated that the common designing factors of line shape, line/space ratio, reference layer and solder resist influence microstrip line SI in the significant reference of designer-making PCB layout.