Search results

The purpose of the paper is to propose an efficient and accurate force/torque (F/T) sensing method for the robotic wrist-mounted six-dimensional F/T sensor based on an excitation trajectory.

This paper presents an efficient and accurate F/T sensing method based on an excitation trajectory. First, the dynamic identification model is established by comprehensively considering inertial forces/torques, sensor zero-drift values, robot base inclination errors and forces/torques caused by load gravity. Therefore, the sensing accuracy is improved. Then, the excitation trajectory with optimized poses is used for robot following and data acquisition. The data acquisition is not limited by poses and its time can be significantly shortened. Finally, the least squares method is used to identify parameters and sense contact forces/torques.

Experiments have been carried out on the self-developed robot manipulator. The results strongly demonstrate that the proposed approach is more efficient and accurate than the existing widely-adopted method. Furthermore, the data acquisition time can be shortened from more than 60 s to 3 s/20 s. Thus, the proposed approach is effective and suitable for fast-paced industrial applications.

The main contributions of this paper are as follows: the dynamic identification model is established by comprehensively considering inertial forces/torques, sensor zero-drift values, robot base inclination errors and forces/torques caused by load gravity; and the excitation trajectory with optimized poses is used for robot following and data acquisition.

Aiming at the problems of geometric precision misalignment and unconsidered physical constraints between large components during the measurement-assisted assembly, a self-adaptive alignment strategy based on the dynamic compliance center (DCC) is proposed in this paper, using force information to guide alignment compliantly.

First, the self-adaptive alignment process of large components is described, and its geometrical and mechanical characteristics are analyzed based on six-dimensional force/torque (F/T). The setting method of DCC is studied and the areas of DCC are given. Second, the self-adaptive alignment platform of large components driven by the measured six-dimensional F/T is constructed. Based on this platform, the key supporting technologies, including principle of self-adaptive alignment, coordinate transfer, calculation of six-dimensional F/T and alignment process control, are illustrated.

Using the presented strategy, the position and orientation of large component is adjusted adaptively responding to measured six-dimensional F/T and the changes of contact states are consistent with the strategy. Through the setting of DCC, alignment process runs smoothly without jamming.

This strategy is applied to the alignment experiment of large components muff coupling. The experimental results show that the proposed alignment strategy is correct and effective and meets the real-time requirement.

This paper proposed a novel way to apply force information in large component self-adaptive alignment, and the setting method of DCC was presented to make the alignment process more feasible.

The sensorless external force estimation of robot manipulator can be helpful for reducing the cost and complexity of the robot system. However, the complex friction phenomenon of the robot joint and uncertainty of robot model and signal noise significantly decrease the estimation accuracy. This study aims to investigate the friction modeling and the noise rejection of the external force estimation.

A LuGre-linear-hybrid (LuGre-L) friction model that combines the dynamic friction characteristics of the robot joint and static friction of the drive motor is proposed to improve the modeling accuracy of robot friction. The square root cubature Kalman filter (SCKF) is improved by integrating a Sage Window outer layer and a nonlinear disturbance observer (NDOB) inner layer. In the outer layer, Sage Window is integrated in the square root Kalman filter (W-SCKF) to dynamically adjust noise statistics. NDOB is applied as the inner layer of W-SCKF (NDOB-WSCKF) to obtain the uncertain state variables of the state model.

A peg-in-hole contact experiment conducted on a real robot demonstrates that the average accuracy of the estimated joint torque based on LuGre-L is improved by 4.9% in contrast to the LuGre model. Based on the proposed NDOB-WSCKF, the average estimation accuracy of the external joint torque can reach up to 92.1%, which is improved by 4%–15.3% in contrast to other estimation methods (SCKF and NDOB).

A LuGre-L friction model is proposed to handle the coupling of static and dynamic friction characteristics for the robot manipulator. An improved SCKF is applied to estimate the external force of the robot manipulator. To improve the noise rejection ability of the estimation method and make it more resistant to unmodeled state variable, SCKF is improved by integrating a Sage Window and NDOB, and a NDOB-WSCKF external force estimator is developed. Validation results demonstrate that the accuracy of the robot dynamics model and the estimated external force is improved by the proposed method.

To ensure the motion attitude and stable contact force of massage robot working on unknown human tissue environment, this study aims to propose a robotic system for autonomous massage path planning and stable interaction control.

First, back region extraction and acupoint recognition based on deep learning is proposed, which provides a basis for determining the working area and path points of the robot. Second, to realize the standard approach and movement trajectory of the expert massage, 3D reconstruction and path planning of the massage area are performed, and normal vectors are calculated to control the normal orientation of robot-end. Finally, to cope with the soft and hard changes of human tissue state and body movement, an adaptive force tracking control strategy is presented to compensate the uncertainty of environmental position and tissue hardness online.

Improved network model can accomplish the acupoint recognition task with a large accuracy and integrate the point cloud to generate massage trajectories adapted to the shape of the human body. Experimental results show that the adaptive force tracking control can obtain a relatively smooth force, and the error is basically within ± 0.2 N during the online experiment.

This paper incorporates deep learning, 3D reconstruction and impedance control, the robot can understand the shape features of the massage area and adapt its planning massage path to carry out a stable and safe force tracking control during dynamic robot–human contact.

Considering the influence of environmental noise and modeling error during the process of the robotic automatic grinding aero-engine blade, this study aims to propose a method based on the extended state observer (ESO) to reduce the fluctuation of normal grinding force.

First, the measurement range of the six-dimensional force sensor is calibrated according to the maximum acceleration of end-effector and grinding force. Second, the gravity and zero drift compensation model is built to compensate for measurement error. Finally, the switching function is designed based on the difference between the expected grinding force and the actual feedback value. When the value of function stays within the switching band, a nonlinear active disturbance rejection control (ADRC) loop is applied. When the function value reaches outside the switching band, an ESO-based sliding mode control (SMC) loop is applied.

The simulated and experimental results show that the proposed control method has higher robustness compared with proportion-integral-derivative (PID), Fuzzy PID and ADRC.

The processing parameters of this paper are obtained based on the single-factor experiment without considering the correlation between these variables. A new control strategy is proposed, which is not only used to control the grinding force of blades but also promotes the development of industrial control.

ESO is used to observe environmental interference and modeling errors of the system for real-time compensation. The segment control method consisting of ESO-based SMC and ESO-based ADRC is designed to improve the robustness. The common application of the two parts realizes suppression of fluctuation of grinding force.

This purpose of this paper is to design a peg-in-hole controller for a cable-driven serial robot with compliant wrist (CDSR-CW) using cable tensions and joint positions. The peg is connected to the robot link through a CW. It is required that the controller does not rely on any external sensors such as 6-axis wrist force/torque (F/T) sensor, and only the compliance matrix’s estimated value of the CW is known.

First, the peg-in-hole assembly system based on a CDSR-CW is analyzed. Second, a characterization algorithm using micro cable tensions and joint positions to express the elastic F/T at the CW is established. Next, under the premise of only knowing the compliance matrix’s estimate, a peg-in-hole controller based on force/position hybrid control is proposed.

The experiment results show that the plug contact F/T can be tracked well. This verifies the validity and correctness of the characterization algorithm and peg-in-hole controller for CDSR-CWs in this paper.

First, to the authors’ knowledge, there is no relevant work about the peg-in-hole assembly task using a CDSR-CW. Besides, the proposed characterization algorithm for the elastic F/T makes the peg-in-hole controller get rid of the dependence on the F/T sensor, which expands the application scenarios of the peg-in-hole controller. Finally, the controller does not require an accurate compliance matrix, which also increases its applicability.

The purpose of this paper is to introduce a method for stiffness modeling, identification and updating of collaborative robots (cobots). This method operates in real-time and with high precision and can eliminate the modeling error between the actual stiffness model and the theoretical stiffness model.

To simultaneously ensure the computational efficiency and modeling accuracy of the stiffness model, this method introduces the finite element substructure method (FESM) into the virtual joint method (VJM). The stiffness model of the cobots is built by integrating several 6-degree of freedom virtual joints that represent the elastic deformation of the cobot modules, and the stiffness matrices of these modules can be identified and obtained by the FESM. A model-updating method is proposed to identify stiffness influence coefficients, which can eliminate the modeling error between the actual prototype model and the theoretical finite element model.

The average relative error and the cycle time of the proposed method are approximately 6.14% and 1.31 ms, respectively. Compared with other stiffness modeling methods, this method not only has high modeling accuracy in high dexterity poses but also in low dexterity poses.

A hybrid stiffness modeling method is introduced to integrate the modeling accuracy of the FESM into the VJM. Stiffness influence coefficients are proposed to eliminate the modeling error between the theoretical and actual stiffness models.

The purpose of this paper is to conduct a reliable remote manipulation with good contact perception of the remote site. The long-term experience of the authors’ repeatedly confirm that the highest relevance lies in monitoring the wrench acting at a structurally weak point of the work piece rather than monitoring the wrench experienced by the robot end-effector.

The approach followed here is to sense the wrench at the interface of the robot end-effector and the environment. Position and orientation data and environment model are used to arrive at the contact point in real time. The intent of remote contact procedure is understood based on the knowledge of motion trajectory. All the above information is used to develop a wrench transformation to obtain the force diagrams.

The haptic solutions greatly suffer from objectivity, and therefore may result in inconsistency in an operator’s role. Intermediary telepresence through the visual communication of the wrench at the remote site in the form of force diagram provides excellent consistency across the operators and operations. Observing six components of the wrench in separate graphs does not provide on-line error estimate. Force diagrams suggested in the paper are found to be highly effective in perceiving the wrench.

The contact mode operations like assembly, surgery, docking, etc. still suffer due to the lack of easily perceivable wrench visualization. This paper provides solution to such practical issues.

The concept is original, and has evolved steadily over a period of time.

This paper aims to propose a hybrid force/position control algorithm based on the stiffness estimation of the unknown environment. A frequency-division control scheme is developed to improve the applicability and reliability of the robot in welding, polishing and assembly.

The stiffness estimation algorithm with time-varying forgetting factors is used to improve the speed and accuracy of the unknown environmental estimation. The sensor force control and robot position control are adopted in different frequencies to improve system stability and communication compatibility. In the low frequency of sensor force control, the Kalman state observer is used to estimate the robot’s joints information, whereas the polynomial interpolation is used to ensure the smoothness of the high frequency of robot position control.

Accurate force control, as well as the system stability, is attained by using this control algorithm.

The entire algorithm is applied to a six-degrees-of-freedom industrial robot, and experiments are performed to confirm its applicability.

The frequency-division control strategy guarantees the control stability and improves the smoothness of the robot movement.

The assembly of large component in out-field is an important part for the usage and maintenance of aircrafts, which is mostly manually accomplished at present, as the commonly used large-volume measurement systems are usually inapplicable. This paper aims to propose a novel coaxial alignment method for large aircraft component assembly using distributed monocular vision.

For each of the mating holes on the components, a monocular vision module is applied to measure the poses of holes, which together shape a distributed monocular vision system. A new unconstrained hole pose optimization model is developed considering the complicated wearing on hole edges, and it is solved by a iterative reweighted particle swarm optimization (IR-PSO) method. Based on the obtained poses of holes, a Plücker line coordinates-based method is proposed for the relative posture evaluation between the components, and the analytical solution of posture parameters is derived. The required movements for coaxial alignment are finally calculated using the kinematics model of parallel mechanism.

The IR-PSO method derived more accurate hole pose arguments than the state-of-the-art method under complicated wearing situation of holes, and is much more efficient due to the elimination of constraints. The accuracy of the Plücker line coordinates-based relative posture evaluation (PRPE) method is competitive with the singular value decomposition (SVD) method, but it does not rely on the corresponding of point set; thus, it is more appropriate for coaxial alignment.

An automatic coaxial alignment system (ACAS) has been developed for the assembly of a large pilotless aircraft, and a coaxial error of 0.04 mm is realized.

The IR-PSO method can be applied for pose optimization of other cylindrical object, and the analytical solution of Plücker line coordinates-based axes registration is derived for the first time.