Search results

This paper aims to study the impact of transient velocity changes on sealing performance during reciprocating sealing processes.

Establish a model of transient mixed lubrication, solve the transient Reynolds equation, consider the effect of temperature rise at the seal interfaces, and determine the behavior of the seal interfaces, such as film thickness and fluid pressure. Evaluation with friction and leakage rate, calculate the variation of sealing performance with reciprocating velocity under different working conditions, and verify it through bench experiments.

Within a reciprocating stroke, the frictional force decreases with increasing velocity, and the frictional force of the outstroke is greater than that of the instroke; at the time of the stroke transition, the fluid pressure is smallest and the rough peak contact pressure is greatest. At present, the dynamic pressure effect of fluids is the largest, and the friction force also increases, which increases the risk of material wear and failure. Friction and leakage increase with increasing pressure and root mean square roughness. As temperature increases, friction increases and leakage decreases. In studying the performance variations of seal components through a reciprocating sealing experiment, it was found that the friction force decreases with increasing velocity, which is consistent with the calculated results and more similar to the calculated results considering the temperature rise.

This study provides a reference for the study of transient sealing performance.

The rock drill’s drill tail experiences high-frequency fretting simultaneously in the rotational and axial directions. Due to the complex working characteristics and the low viscosity of the water medium, the pure water seal is susceptible to damage and failure. The purpose of this paper is to enhance the water seal’s performance.

The Y-shaped seal ring is modeled and simulated using orthogonal testing. Through analysis of the impact of various seal section parameters on sealing performance, the maximum contact stress and maximum Von Mises stress are selected as indicators of sealing effectiveness.

The maximum contact stress is proportional to lip thickness and chamfer length but inversely proportional to lip length. Meanwhile, the maximum Von Mises stress is directly influenced by lip depth and the included angle of the lip and drill tail but is inversely proportional to the lip thickness. The enhanced Y-shaped water seal sees reductions of 15% and 45% in maximum contact stress and maximum Von Mises stress, respectively.

This paper used analytical method and model that is helpful for design of the water seal’s structure in complex working characteristics and the low viscosity of the water medium.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2023-0366/

This paper aims to focus on the high-speed rotary lip seal in aircraft engines, combining its service parameters, its own structure and application conditions, to study the influence of different eccentric forms, eccentricity, rotational speed and other factors on the performance of the rotary lip seal.

A numerical simulation model for high-speed eccentric rotary lip seals has been developed based on the theory of elastic hydrodynamic lubrication. This model comprehensively considers the coupling of multiple physical fields, including interface hydrodynamics, macroscopic solid mechanics and surface microscopic contact mechanics, under the operating conditions of rotary lip seals. The model takes into account eccentricity and uses the hazardous cross-sectional method to quantitatively predict sealing performance parameters, such as leakage rate and friction force.

Eccentricity has a large impact on lip seal performance; lips are more susceptible to wear failure under static eccentricity and to leakage failure under dynamic eccentricity.

This study provides a new idea for the design of rotary lip seal considering eccentricity, which is of guiding significance for the engineering application of rotary lip seal.

Ferrofluid seals are known for their low friction torque and high tightness. However, they have some limitation due to the allowable rotational speed. The work presented here analyzes the performance of newly designed seals which are a combination of a ferrofluid and a centrifugal seal. The new seals can operate at high speeds. The purpose of this study is to theoretically predict the performance of combined seals.

Three seals were designed and selected for analysis. A version of the seals with a nonmagnetic insert is also considered, the purpose of which is to facilitate the installation and return of ferrofluid during low rotational speeds. The analyses were based on combining the results of numerical simulation of magnetic field distribution with mathematical models.

A combination of ferrofluid sealing and centrifugal sealing is possible. Analyses showed that the combined seal could hold a minimum pressure of 190 kPa in the velocity range of 0–100 m/s. The problem with this type of seal is the temperature.

New seal designs are presented. Key parameters that affect the seal operation are discussed. A methodology that can be used in the design of such seals is presented.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0221/.

This paper aims to study the deformation mechanism of polytetrafluoroethylene (PTFE) oil seal under a wide temperature range cycle.

This study categorizes the oil seal operation into three states: assembly, heating-up and cooling. The deformation equation for the oil seal is developed for each state, considering the continuity between them. The investigation of the oil seal’s deformation trends and mechanisms is performed using the ANSYS Workbench.

The assembling process results in a radial shrinkage of the skeleton, causing the centroid to move toward the axis. During heating-up, the outer diameter of the skeleton slightly expands, whereas the inner diameter sharply contracts toward the axis, leading to a further reduction in the centroid’s distance from the axis. Upon cooling, both the inner and outer diameters continue to contract toward the axis, causing the centroid to persist in its movement toward the axis. Consequently, after undergoing a heating-up and cooling cycle ranging from 20°C to 180°C, the outer diameter of the PTFE oil seal reduces by 0.92 mm from its original deformation, ensuring minimal contact between the skeleton and housing. As a result of the reduced static friction torque at the skeleton, the oil seal rotates along the shaft.

The deformation mechanism of PTFE oil seals under a wide temperature range cycle was investigated, aiming to address the concerns related to the rotation along the shaft and leakage.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2023-0142/

This paper aims to study the motion trajectory of the oil seal for shaft in eccentric state and derive equation of lip motion trajectory.

This paper analyzes the force during the motion of the eccentric lip by considering the material viscoelasticity, and a cam-plate mechanism is established as an equivalent model for the motion between the shaft and the lip; according to this, the equation of lip motion trajectory is derived.

The trajectory of the lip lags that of the shaft in the eccentric state because the viscoelasticity-affected lip recovery velocity is lower than the shaft recovery speed. The lip trajectory enters the lag phase earlier and the lag phase’s duration is longer with the increase of the eccentricity and rotational speed, because the deviation of the recovery velocities between the lip and the shaft will be exacerbated.

Innovatively, by considering the viscoelasticity of the material, the cam-plate mechanism is used to equivalent the motion of the shaft-lip to derive the equation for the radial motion trajectory of the eccentric lip. The regularity of lip motion is the key to determining the performance of oil seals, and the eccentric lip trajectory research method revealed in this paper provides a research basis for the performance research and optimization of eccentric oil seals.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-06-2023-0161/

This paper aims to investigate the effect of frictional heat on the wear of high-speed rotary lip seals in engines.

In this research paper, the authors focus on the high-speed rotating lip seal of aircraft engines. Using the hybrid lubrication theory, a thermal-fluid-solid coupled numerical simulation model is established to investigate the influence of parameters such as contact pressure distribution, temperature rise and leakage rate on the sealing performance under different operating conditions. By incorporating the Rhee wear theory and combining simulation results with experimental data, a method for predicting the wear of the rotating seal lip profile is proposed. Experimental validation is conducted using a high-speed rotating test rig.

The results indicate that as the speed increases, the rise in frictional heat leads to a decrease in the sealing performance of the lip seal contact region. The experimental results show a similar trend to the numerical simulation results, and considering the effect of frictional heat, the predicted wear of the lip seal profile aligns more closely with the actual wear curve. This highlights the importance of considering the influence of frictional heat in the analysis of rotating seal mechanisms.

This study provides a reference for the prediction of wear profiles of engine high-speed rotary lip seals.

This paper aims to prevent gasket sealing failure in engineering, accurately predict gasket life, extend system life and improve sealing reliability. The accelerated life test method of flexible graphite composite–reinforced gaskets is established, the life distribution law of flexible graphite composite–reinforced gaskets is revealed, and the life prediction method of flexible graphite composite–reinforced gaskets with different allowable leakage rates is proposed, which can provide a reference for the life prediction of other types of gaskets.

In this study, flexible graphite composite–reinforced gaskets were tested for long-term high-temperature sealing performance on a multi-sample gasket accelerated life test rig. The data were also analyzed using the least squares method and the K-S hypothesis calibration method. A gasket time-dependent leakage model and an accelerated life model were also developed. Constant stress-accelerated life tests were conducted on flexible graphite composite–reinforced gaskets. On this basis, a gasket life prediction method at different allowable leakage rates was proposed.

The life distribution law of flexible graphite composite–reinforced gaskets is revealed. The results show that the life of the gasket obeys the Weibull distribution. The time-correlated leakage model and accelerated life model of the gasket were established. And the accelerated life test method of the flexible graphite composite–reinforced gasket was established. The life distribution parameters, accelerated life model parameters and life estimates of gaskets were obtained through tests. On this basis, a gasket life prediction method under different leakage rates was proposed, which can be used as a reference for other types of gaskets.

The research in this paper can better provide guidance for the use and replacement of gaskets in the project, which is also very meaningful for predicting the leakage condition of gaskets in the bolted flange connection system and taking corresponding control measures to reduce energy waste and pollution and ensure the safe operation of industrial equipment.

A multi-specimen gasket-accelerated life test device has been developed, and the design parameters of the device have reached the international advanced level. The life distribution law of the flexible graphite composite–reinforced gasket was revealed. The accelerated life test method for the flexible graphite composite–reinforced gasket was established. The life prediction method of the flexible graphite composite–reinforced gasket under different allowable leakage rates was proposed.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2023-0254/

A new type of variable damping viscous damper is developed to meet the settings of different damping parameter values at different working stages. Its main principle and design structure are introduced, and the two-stage and multi-stage controllable damping methods are proposed.

The theoretical calculation formulas of the damping force of power-law fluid variable damping viscous damper at elongated holes are derived, aiming to provide a theoretical basis for the development and application of variable damping viscous dampers. For the newly developed variable damping viscous damper, the dynamic equations for the seismic reduction system with variable damping viscous dampers under a multi-degree-of-freedom system are established. A feasible calculation and analysis method is proposed to derive the solution process of time history analysis. At the same time, a program is also developed using Matlab. The dynamic full-scale test of a two-stage variable damping viscous damper was conducted, demonstrating that the hysteresis curve is complete and the working condition is stable.

Through the calculation and analysis of examples, the results show that the seismic reduction effect of high and flexible buildings using the seismic reduction system with variable damping viscous dampers is significant. The program developed is used to analyze the seismic response of a broadcasting tower using a variable damping TMD system under large earthquakes. The results indicate that the installation of variable damping viscous dampers can effectively control the maximum inter-story displacement response of TMD water tanks and can effectively consume seismic energy.

This method can provide a guarantee for the safe and effective operation of TMD in wind and vibration control.

This study aims to improve the tribological properties of hydrodynamic journal bearing via surface texture, as well as the wear and antifriction mechanisms of textured bearing were represented. It provides a design direction for solving the tribological problem of rotor-bearing system.

In this paper, the variation of surface texture parameters (e.g. texture diameter, d; area density, sp; and depth, hp) were analyzed based on finite difference method. The optimal surface texture parameters were obtained by designing orthogonal experiments, and the relationship between friction and wear properties and microstructure was studied via combining electron probe microanalyzer, scanning electron microscope, X-ray diffractometer and friction and wear testing machine.

Dimensionless film pressure P increased as the d increased, whereas P first increased and then decreased as the sp and hp increased, and the maximum P was got as sp = 15% and hp = 25 µm, respectively. The friction coefficient of textured surface with suitable parameters was effectively reduced and the textured surface with the best antifriction effect was 5#. Orthogonal experimental design analysis showed that the influence order of factors on friction coefficient was as follows: sp > sp × d > d > d × hp > hp > sp × hp and the friction coefficient first decreased and then increased as the sp, d and hp increased. In addition, the friction and wear mechanism of textured bearing were three body friction and abrasive wear as the matrix structure and hard phase were a single β phase and Mn5Si3, respectively. While the antifriction mechanism of textured surface was able to store abrasive particles and secondary hydrodynamic lubrication was formed.

The sample with reasonable texture parameter design can effectively reduce friction and wear of hydrodynamic journal bearing without reducing the service life, which can provide a reference for improving the lubrication performance and mechanical efficiency of rotor-bearing system.