Search results

A SPANWISE rotating cylinder placed at a suitable location in an aerofoil with the cylinder's upper surface moving rearwards in the direction of the local air flow can serve to re‐energize the boundary layer on the aerofoil. For example, when placed between a flap and a wing with the cylinder protruding substantially into the air flow as shown schematically in no. 1, the moving surface of the cylinder destroys, by viscous shear action, the low‐energy boundary layer impinging on the cylinder from the wing and results in a new boundary layer on the flap's upper surface which has a higher energy level adequate to negotiate the adverse pressure gradients and flow conditions existing at the rear of a flap deflected through a large angle. The boundary layer re‐energizing function of the cylinder depends on its upward protrusion, on its peripheral speed, and on the local flap geometry. The beneficial effects of the rotating cylinder on the flow fields have been visualized in two dimensional smoke studies conducted by Alvarez Caldcrón and Arnold of Stanford University on a flap designed for deflected slipstream V/S.T.O.L. aircraft. Fig. 2 shows flow around the flap with the cylinder stationary. It exhibits complete flow separation at the flap which is also typical of a slotted flap deflected through a large angle. The large white disk is a cylinder end plate; the actual cylinder appears in the darker circular shade of small diameter. The photograph of FIG. 3 was taken with the cylinder rotating: it shows a radical flow change not only in the total elimination of flow separation on the flap but in the induction of strong upwash fields and low pressure regions toward the leading edge of wing itself which obviously greatly increases lift and decreases wing pitching moments.

Mixed recirculatory flow in the annuli of stationary and rotating horizontal cylinders were studied numerically. A set of distorted ‘false transient’ parameters were introduced to speed up the steady state solution of the unsteady vorticity, energy and stream function—vorticity equations. The inner cylinder of the annuli is assumed heated and rotating at Reynolds numbers that exclude the effects of centrifugal acceleration and three‐dimensional Taylor vortices. The Prandtl number considered is in the range of 0.01 to 1.0 and Rayleigh number in the range of 10² to 10⁶. Radius ratios of the cylinders considered are 1.25, 2.5 and 5.0. For a radius ratio of 2.5, inner cylinder rotation in the Reynolds number range of 0 to 1120 was considered. Vertical eccentricities in the range of ±2/3 were studied for cases of the rotating inner cylinder. Numerical experiments show that the mean Nusselt number increases with Rayleigh number for both cases of concentric and eccentric stationary inner cylinder. At a Prandtl number of order 1.0 with a fixed Rayleigh number, when the inner cylinder is made to rotate, the mean Nusselt number decreases throughout the flow. At lower Prandtl number of the order 0.1 to 0.01, the mean Nusselt number remained fairly constant with respect to the rotational Reynolds number.

The purpose of this paper is to numerically investigate two dimensional steady state convective heat transfer in a differentially heated square cavity with constant temperatures and an inner rotating cylinder. The gap between the cylinder and the enclosure walls is filled with power law non-Newtonian fluid.

Finite volume-based CFD software, Fluent (Ansys 15.0) is used to solve the governing equations. Attribution of the various flow parameters of fluid flow and heat transfer are investigated including Rayleigh number, Prandtl number, power law index, the cylinder radius and the angular rotational speed.

Outcomes are reported in terms of isotherms, streamlines and average Nusselt number (Nu) of the heated wall for various considered here.

A detailed investigates is needed in the context of 3D flow. This will be a part of the future work.

The effect of a rotating cylinder on heat transfer and fluid flow in a differentially heated rectangular enclosure filled with power law non-Newtonian fluid has practical importance in the process industry.

The results of this study may be of some interest to the researchers of the field of chemical or process engineers.

This study aims to numerically examine mixed convection of CuO-water nanofluid in a three-dimensional (3D) vented cavity with inlet and outlet ports under the influence of an inner rotating circular cylinder, homogeneous magnetic field and surface corrugation effects. In practical applications, it is possible to encounter some of the considered configurations in a vented cavity such as magnetic field, rotating cylinder and it is also possible to specially add some of the active and passive control means to control the convection inside the cavity such as adding nanoparticles, corrugating the surfaces. The complicated physics with nanofluid under the effects of magnetic field and inclusion of complex 3D geometry make it possible to use the results of this numerical investigation for the design, control and optimization of many thermal engineering systems as mentioned above.

The bottom surface is corrugated with a rectangular wave shape, and the rotating cylinder surface and cavity bottom surface were kept at constant hot temperatures while the cold fluid enters the inlet port with uniform velocity. The complicated interaction between the forced convection and buoyancy-driven convection coupled with corrugated and rotating surfaces in 3D configuration with magnetic field, which covers a wide range of thermal engineering applications, are numerically simulated with finite element method. Effects of various pertinent parameters such as Richardson number (between 0.01 and 100), Hartmann number (between 0 and 1,000), angular rotational speed of the cylinder (between −30 and 30), solid nanoparticle volume fraction (between 0 and 0.04), corrugation height (between 0 and 0.18H) and number (between 1 and 20) on the convective heat transfer performance are numerically analyzed.

It was observed that the magnetic field suppresses the recirculation zone obtained in the lower part of the inlet port and enhances the average heat transfer rate, which is 10.77 per cent for water and 6.86 per cent for nanofluid at the highest strength. Due to the thermal and electrical conductivity enhancement of nanofluid, there is 5 per cent discrepancy in the Nusselt number augmentation with the nanoadditive inclusion in the absence and presence of magnetic field. The average heat transfer rate of the corrugated surface enhances by about 9.5 per cent for counter-clockwise rotation at angular rotational speed of 30 rad/s as compared to motionless cylinder case. Convective heat transfer characteristics are influenced by introducing the corrugation waves. As compared to number of waves, the height of the corrugation has a slight effect on the heat transfer variation. When the number of rectangular waves increases from N = 1 to N = 20, approximately 59 per cent of the average heat transfer reduction is achieved.

In this study, mixed convection of CuO-water nanofluid in a 3D vented cavity with inlet and outlet ports is numerically examined under the influence of an inner rotating circular cylinder, homogeneous magnetic field and surface corrugation effects. To the best of authors knowledge such a study has never been performed. In practical applications, it is possible to encounter some of the considered configurations in a vented cavity such as magnetic field, rotating cylinder and it is also possible to specially add some of the active and passive control means to control the convection inside the cavity such as adding nanoparticles, corrugating the surfaces. The complicated physics with nanofluid under the effects of magnetic field and inclusion of complex 3D geometry make it possible to use the results of this numerical investigation for the design, control and optimization of many thermal engineering systems as mentioned above.

The purpose of this paper is to apply the boundary element method (BEM) to Stokes flow between eccentric rotating cylinders, considering the case when viscous dissipation plays a significant role and determining the Nusselt number as a function of cylinder geometry parameters.

The problem is described by the equation of motion of Stokes flow and an energy equation with a viscous dissipation term. First, the velocity field and the viscous dissipation term were determined from the momentum equation. The determined dissipation of energy and the constant temperature on the cylinder walls are the conditions for the energy equation, from which the temperature distribution and the heat flux at the boundary of the cylinders are determined. Numerical calculations were performed using the author’s own computer program based on BEM. Verification of the model was carried out by comparing the temperature determined by the BEM with the known theoretical solution for the temperature distribution between two rotating concentric cylinders.

As the ratio of the inner cylinder diameter to the outer cylinder diameter (r1/r2) increases, the Nusselt number increases. The angle of inclination of the function of the Nusselt number versus r1/r2 increases as the distance between the centers of the inner and outer cylinders increases.

The computational results may be used for the design of slide bearings and viscometers for viscosity testing of liquids with high viscosity where viscous dissipation is important. In the work, new integral kernels were determined for BEM needed to determine the viscous dissipation component.

The flow between eccentric rotating cylinders when either the outer or inner cylinder is stationary is analysed both for the creeping flow approximation and for the case when inertial effects are not negligible. Numerical solutions are obtained using a finite difference ADI scheme and a fine orthogonal bipolar coordinate grid. When the centres of the two cylinders are far enough, a two‐dimensional recirculation zone appears in the region where the gap spacing is greatest. On increasing the eccentricity, the recirculation zone becomes bigger and the separation and reattachment points move towards the region of narrowest gap. Further increase of the eccentricity results in the formation of a saddle point between the cylinders at the region of narrowest gap. As the Reynolds numbers increases, inertial effects modify slightly the recirculation region; the separation point moves upstream and the reattachment point moves downstream when either the inner or the outer cylinder rotate.

This paper aims to study the mixed convective process due to various dynamics, namely, inner rotating cylinders and upper-wavy wall movement for the first time.

The Galerkin finite element method together with the characteristic-based split scheme is applied to solve the governing system.

The main outcomes revealed that the direction of the rotation of the cylinders, radius and locations of the rotating shapes are beneficial controlling elements for the enhancement of heat transfer. Also, for all the considered cases, values of the Bejan number indicate that the fluid friction irreversibility is dominance compared to the heat transfer irreversibility. Further, average values of the heat transfer entropy, fluid friction entropy and total entropy are minimized in the case of fixed cylinders regardless of the cylinder radius.

The authors are interested in the mixed convection case due to regular boundaries and hence this simulation purposes a first attempt to examine the mixed convective flow due to irregular wavy boundaries. This study considered various dynamics, namely, inner rotating cylinders and wavy-lid driven wall which makes it more attractive to the readers. Various cases based on radius of the cylinder and direction of the rotations together with several locations of the rotating shapes are taken into account which makes the current simulation is comprehensive. Various studies presented in this field are made by commercial software and these treatments need special conditions (having limitation) but the current solution methodology is based on a finite element method home-code. Various important impacts, are, also, examined, namely, inclined geometry, inclined magnetic field, thermal radiation and heat generation/absorption. The entropy of the current complex system is analyzed based on the second law of thermodynamics.

The purpose of this study is to numerically analyze the mixed convection and entropy generation in an annulus with a rotating heated inner cylinder for single-wall carbon nanotube (SWCNT)–water nanofluid flow using local thermal nonequilibrium (LTNE) model. An examination of the system behavior is presented considering the heat-generating solid phase inside the porous layer partly filled at the inner surface of the outer cylinder.

The discretized governing equations for nanofluid and porous layer by means of the finite volume method are solved by using the SIMPLE algorithm.

It is found that the buoyancy force and rotational effect have an important impact on the change of the strength of streamlines and isotherms for nanofluid flow. The minimum average Nusselt number on the inner cylinder is obtained at Ra$_E$ = 10$^4$, and the minimum total entropy generation is found at Re = 400 for given parameters. The entropy generation minimization is determined in case of different nanoparticle volume fractions. It is observed that at the same external Rayleigh numbers, the LTNE condition obtained with internal heat generation is very different from that without heat generation.

To the best of the authors’ knowledge, there is no previous paper presenting mixed convection and entropy generation of SWCNT–water nanofluid in a porous annulus under LTNE condition. The addition of nanoparticles to based fluid leads to a decrease in the value of minimum total entropy generation. Thus, using nanofluid has a significant role in the thermal design and optimization of heat transfer applications.

The purpose of this study is to numerically examine the mixed convection of CuO-water nanofluid due to a rotating inner hot circular cylinder in a 3D cubic enclosure with phase change material (PCM) attached to its vertical surface. Heat transfer and fluid flow characteristics were examined for various values of pertinent parameters.

Finite element method was used in the numerical simulation. Influence of various pertinent parameters such as Rayleigh number (between 10$^5$ and 10$^6$), Hartmann number (between 0 and 100), angular rotational speed of the cylinder (between −50 and 50), solid nanoparticle volume fraction (between 0 and 0.04) and PCM parameters (height-between 0.2H and 0.8H, thermal conductivity ratio- between 0.1 and 10) on the convective heat transfer characteristics are numerically studied.

It was observed that local heat transfer variations along the hot surface differ significantly for the cases with and without magnetic field where three distinct hot spots of peak Nusselt number are established when magnetic field is imposed. The average Nusselt number enhancement with the nanofluid at the highest particle volume fraction is 52.85 per cent at Hartmann number of 100, whereas its value is 39.76 per cent for the case in the absence of magnetic field. When the inner cylinder rotates, flow and thermal fields are affected within the cavity. The local heat transfer variations spread over the hot surface with cylinder rotation and 16.43 per cent of reduction in the average heat transfer is obtained with counter-clockwise rotation at 100 rad/sec. An enhancement in the PCM height and a reduction in the thermal conductivity of the PCM result in average heat transfer deterioration for the 3D cavity. The amount of the reduction is 43 per cent when the PCM height is increased from 0.2H to 0.8H, whereas 19.10 per cent enhancement in the heat transfer is achieved when thermal conductivity ratio (PCM) to the base fluid is increased from 0.1 to 10.

Such configurations can be designed for convection control, and in our case, various methods are available. Some of the investigated methods can be used in applications where magnetic field already exists. Convection control study in 3D cavity gives more realistic results as compared to 2D configurations, and results of the current investigation may be used for the design, optimization and flow control of many thermal applications involving magnetic field effects.

This study aims to examine the effects of cross-flow and multiple jet impingement on conductive panel cooling performance when subjected to uniform magnetic field effects. The cooling system has double rotating cylinders.

Cross-flow ratios (CFR) ranging from 0.1 to 1, magnetic field strength (Ha) ranging from 0 to 50 and cylinder rotation speed (Rew) ranging from −5,000 to 5,000 are the relevant parameters that are included in the numerical analysis. Finite element method is used as solution technique. Radial basis networks are used for the prediction of average Nusselt number (Nu), average surface temperature of the panel and temperature uniformity effects when varying the impacts of cross-flow, magnetic field and rotations of the double cylinder in the cooling channel.

The effect of CFR on cooling efficiency and temperature uniformity is favorable. By raising the CFR to the highest value under the magnetic field, the average Nu can rise by up to 18.6%, while the temperature drop and temperature difference are obtained as 1.87°C and 3.72°C. Without cylinders, magnetic field improves the cooling performance, while average Nu increases to 4.5% and 8.8% at CR = 0.1 and CR = 1, respectively. When the magnetic field is the strongest with cylinders in channel at CFR = 1, temperature difference (ΔT) is obtained as 2.5 °C. The rotational impacts on thermal performance are more significant when the cross-flow effects are weak (CFR = 0.1) compared to when they are substantial (CFR = 1). Cases without a cylinder have the worst performance for both weak and severe cross-flow effects, whereas using two rotating cylinders increases cooling performance and temperature uniformity for the conductive panel. The average surface temperature lowers by 1.2°C at CFR = 0.1 and 0.5°C at CFR = 1 when the worst and best situations are compared.

The outcomes are relevant in the design and optimization-based studies for electric cooling, photo-voltaic cooling and battery thermal management.