Search results

Competitive edge will not come from cost alone in the European Single Market, nor in competition with the Far East. ICL provides a case study of an IT manufacturing company in transition. Realignment in the marketplace requires above all the successful management of change in people, attitudes and organisation.

This paper aims to investigate the effect of Powell–Eyring fluid induced by a stretched sheet. Heat and mass transfer under the influence of magnetic dipole over a stretching sheet are taken into account.

Nonlinear coupled governing equations are solved using the optimal homotopy asymptotic technique, and a computer software package BVPh 2.0 is used for numerical computations.

Impact of significant quantities is graphically examined. It is seen that the heat transfer deceases for higher values of viscous dissipation parameter, radiation parameter, Dufour number, whereas it increases for bigger values of Prandtl number. The numerical results have been validated through comparison with existing literature as a special case of proposed model and perceived that the Soret number has reining role to increase the rate of heat transfer.

To the best of the authors’ knowledge, this study is reported for the first time.

This paper aims to focus on the inclusion of the frequency behavior of grounding system effect on surge arrester (SA) model parameters’ estimation.

The grounding system impedance and its frequency behavior are the factors that have influence on the SA performance. Up to now, the grounding system impedance effect and the frequency behavior of the soil parameters have not been studied for the estimation of the parameters of the SA frequency-dependent model. In this paper, the grounding system’s influence on the SA dynamic model has been simulated for rod- and counterpoise-shaped electrodes. Particle swarm optimization with a grey wolf optimization algorithm has been implemented as an optimization algorithm to adjust the parameters of the SA dynamic model.

The results show that the frequency behavior of the grounding impedance and soil electrical parameters can impress the optimum parameters of the SA frequency-dependent model and should be considered for more reliable results. Also, the results evidence that the proposed optimization method provides more accurate results compared to other optimization methods.

To the best of the authors’ knowledge, this work is one of the first attempts to investigate the effect of frequency grounding system on SA frequency-dependent model parameters.

May 12,1967 Factory — Dangerous machinery (fencing) — Guard provided and ready for use — Machine being re‐set — Guard provided for operation not used by workman — Whether machine “fenced” — Workman re‐setting machine without calling on help of assistant — Whether reckless — Whether amounting to contributory negligence — Factories Act, 1961 (9 & 10 Eliz.II, c.34), ss. 14,16.

This paper gives a review of the finite element techniques (FE) applied in the area of material processing. The latest trends in metal forming, non‐metal forming and powder metallurgy are briefly discussed. The range of applications of finite elements on the subjects is extremely wide and cannot be presented in a single paper; therefore the aim of the paper is to give FE users only an encyclopaedic view of the different possibilities that exist today in the various fields mentioned above. An appendix included at the end of the paper presents a bibliography on finite element applications in material processing for the last five years, and more than 1100 references are listed.

It seems intuitive that as firms continue to try and keep in touch with the customers they serve, research should play an increasingly important role in determining the needs and wants of the consumer. Accordingly, as goods and services are tailored to meet these needs, so too does the accompanying advertising. Additionally, there is constant pressure on advertising agencies to produce advertising that consistently meets the objectives of their clients. Marketing departments, in turn, have to justify and be accountable to top management for advertising budgets. Consequently, agencies increasingly have to provide measures of effectiveness (Flandin et al 1992). In order to optimize the process(es) that will meet client objectives, agencies have to ensure that they understand how the consumer thinks and feels. One such approach to understanding the consumer's view is account planning. The main objective of this paper will be to provide a thorough review of the account planning phenomenon in advertising and in so doing, highlight the use of advertising research from a developmental perspective. This paper will describe the account planning process and how it differs from traditional agency practices. The justification for such a paper is the fact that billions of dollars are spent annually on advertising, in the hopes that the advertiser's objectives will consistently be met. If it could be demonstrated that increased attention to the consumer, in the development stages of advertising leads to more effective advertising than when consumer input is limited to the evaluation of advertising, after the fact, this would be of significant interest to advertisers as well as advertising agencies.

Attempts to transform health systems have in many countries involved starting to pay healthcare providers through a DRG system, but that has involved managerial workarounds. Managerial workarounds have seldom been analysed. This paper does so by extending and modifying existing knowledge of the causes and character of clinical and IT workarounds, to produce a conceptualisation of the managerial workaround. It further develops and revises this conceptualisation by comparing the practical management, at both provider and purchaser levels, of hospital DRG payment systems in England, Germany and Italy.

We make a qualitative test of our initial assumptions about the antecedents, character and consequences of managerial workarounds by comparing them with a systematic comparison of case studies of the DRG hospital payment systems in England, Germany and Italy. The data collection through key informant interviews (N = 154), analysis of policy documents (N = 111) and an action learning set, began in 2010–12, with additional data collection from key informants and administrative documents continuing in 2018–19 to supplement and update our findings.

Managers in all three countries developed very similar workarounds to contain healthcare costs to payers. To weaken DRG incentives to increase hospital activity, managers agreed to lower DRG payments for episodes of care above an agreed case-load ‘ceiling' and reduced payments by less than the full DRG amounts when activity fell below an agreed ‘floor' volume.

Empirically this study is limited to three OECD health systems, but since our findings come from both Bismarckian (social-insurance) and Beveridge (tax-financed) systems, they are likely to be more widely applicable. In many countries, DRGs coexist with non-DRG or pre-DRG systems, so these findings may also reflect a specific, perhaps transient, stage in DRG-system development. Probably there are also other kinds of managerial workaround, yet to be researched. Doing so would doubtlessly refine and nuance the conceptualisation of the ‘managerial workaround’ still further.

In the case of DRGs, the managerial workarounds were instances of ‘constructive deviance' which enabled payers to reduce the adverse financial consequences, for them, arising from DRG incentives. The understanding of apparent failures or part-failures to transform a health system can be made more nuanced, balanced and diagnostic by using the concept of the ‘managerial workaround'.

Managerial workarounds also appear outside the health sector, so the present analysis of managerial workarounds may also have application to understanding attempts to transform such sectors as education, social care and environmental protection.

So far as we are aware, no other study presents and tests the concept of a ‘managerial workaround'. Pervasive, non-trivial managerial workarounds may be symptoms of mismatched policy objectives, or that existing health system structures cannot realise current policy objectives; but the workarounds themselves may also contain solutions to these problems.

Previous work has suggested that the adhesion between oil and metallic surfaces of an engine could be an important factor in determining crankcase cleanliness. It can be shown that it is only necessary to measure the spreading pressure of an oil on metal in order to get a direct measure of the work of adhesion, Surface tensions of lubrictaing oils vary very little and it can be assumed that the critical film pressure (C.F.P.) obtained with a given apparatus is an acceptable measure of the work of adhesion as well as of the spreading pressure. Oils of similar properties may vary tenfold in their C.F.P's. The addition of additives influences the spreading pressure, the largest increments in C.F.P. being given by dispersant and detergent additives.

A complete electrolytic dummying system providing efficient automatic removal of soluble base‐metal impurities from nickel solutions while simultaneously plating is now available as an optional feature in the Carbolator (Fig. 1), which at the same time carbon treats and filters, according to an announcement by the manufacturer, Sethco Manufacturing Corp., One Bennington Avenue, Freeport, New York.