Search results

This study aims on a broad review of Concrete's Rheological Properties. The Concrete is a commonly used engineering material because of its exquisite mechanical interpretation, but the addition of constituent amounts has significant effects on the concrete’s fresh properties. The workability of the concrete mixture is a short-term property, but it is anticipated to affect the concrete’s long-term property.

In this review, the concrete and workability definition; concrete’s rheology models like Bingham model, thixotropy model, H-B model and modified Bingham model; obtained rheological parameters of concrete; the effect of constituent’s rheological properties, which includes cement and aggregates; and the concrete’s rheological properties such as consistency, mobility, compatibility, workability and stability were studied in detail.

Also, this review study has detailed the constituents and concrete’s rheological properties effects. Moreover, it exhibits the relationship between yield stress and plastic viscosity in concrete’s rheological behavior. Hence, several methods have been reviewed, and performance has been noted. In that, the abrasion resistance concrete has attained the maximum compressive strength of 73.6 Mpa; the thixotropy approach has gained the lowest plastic viscosity at 22 Pa.s; and the model coaxial cylinder has recorded the lowest stress rate at 8 Pa.

This paper especially describes the possible strategies to constrain improper prediction of concrete’s rheological properties that make the workability and rheological behavior prediction simpler and more accurate. From this, future guidelines can afford for prediction of concrete rheological behavior by implementing novel enhancing numerical techniques and exploring the finest process to evaluate the workability.

Laboratory investigation of the effect of carbonate contaminant on the rheological properties of drilling mud based on Bingham plastic flow model was carried out. The rheological properties investigated were yield point, plastic viscosity, initial gel strength and ten‐minute gel strength. Eight samples of the same mud were used in the investigation. Equipment used in studying the rheological properties was a direct‐indicating viscometer. The result of the investigation showed that carbonate contaminant in drilling mud adversely increases the yield point and gel strength. Marginal increase in the plastic viscosity of the mud was also observed. The mud flocculated as the amount of carbonate increased.

The purpose of this paper is to fabricate Nylon6-Al-Al2O₃-based alternative fused deposition modeling process (FDM) feedstock filament in place of commercial acrylonitrile butadiene styrene (ABS) filament (having required rheological and mechanical properties) for rapid manufacturing (RM) and rapid tooling (RT) applications. The detailed steps for fabrication of alternative FDM feedstock filament (as per field application) with relatively low manufacturing cost and tailor-made properties have been highlighted.

The rheological and mechanical suitability of nylon6-Al-Al2O₃ feedstock filament has been investigated experimentally. The approach is to predict and incorporate essential properties such as flow rate, flexibility, stiffness and mechanical strength at processing conditions and compared with commercial ABS material. The proportions of various constituents have been varied to modify and improve rheological behavior and mechanical properties of alternative FDM feedstock filament.

The alternative material of feed stock filament was successfully developed and loaded in commercial FDM setup without changing any hardware and software. The result of study suggests that the newly developed composite material filament has relatively poor mechanical properties but have highly thermal stability and wear resistant as compared to ABS filament and hence can be used for tailor-made applications.

In this work, no additive was added for improving the bond formation of metal and polymeric materials. The newly developed filament was prepared on single screw extruder. For more uniform mixing of metal and polymeric materials, further studies may be conducted on twin screw extruder. Also, for the present research work, the testing of newly developed filament has been limited up to mechanical testing, which may be extended to chemical and thermal analysis to understand thermal stability and degradation mechanism of newly developed composite material.

The proportion of filler material (Al-Al2O3) in Nylon6 matrix was set as a constraint, which was adjusted based upon melt flow index of original equipment manufacturer developed material (ABS), and temperature conditions were available at FDM nozzle (so that hardware and software system of commercial FDM setup need not to be altered).

The present approach outlined selection, processing, fabrication and testing procedure for alternate feedstock filament, which fulfills the necessary requirements of FDM process and has been customized for RT and RM applications. This work highlights mechanical strength evaluation of feedstock filament (which is necessary before the loading of material in FDM system). The potential applications of this investigation include RM of functional parts, tailor-made grinding tools for dentists and RT of metal matrix composite having complex geometry.

This paper aims to focus on the development of the three-dimensional (3D) printing filaments based on acrylonitrile butadiene styrene (ABS) copolymer and styrene-ethylene/butylene-styrene (SEBS) block copolymer, with tailored viscoelastic properties and controlled flow during the 3D printing process.

In this investigation, ABS was blended with various amounts of SEBS via a melt mixing process. Then the ABS/SEBS filaments were prepared by a single-screw extruder and printed by the FDM method. The rheological properties were determined using an MCR 501 from Anton-Paar. The melt flow behavior of ABS/SEBS filaments was determined. The morphology of the filaments was studied by scanning electron microscope and the mechanical (tensile and impact) properties, surface roughness and void content of printed samples were investigated.

The rheological results can accurately interpret what drives the morphology and mechanical properties’ changes in the blends. The impact strength, toughness, elongation-at-break and anisotropy in mechanical properties of ABS samples were improved concurrently by adding 40 Wt.% of SEBS. The optimal tensile properties of blend containing 40 Wt.% SEBS samples were obtained at −45°/+45° raster angle, 0.05 mm layer thickness and XYZ build orientation. Optimized samples showed an 890% increase in elongation compared to neat ABS. Also, the impact strength of ABS samples showed a 60% improvement by adding 40 Wt.% SEBS.

The paper simultaneously evaluates the effects of material composition and 3D printing parameters (layer thickness, raster angle and build orientation) on the rheology, morphology, mechanical properties and surface roughness. Also, a mechanical properties comparison between printed samples and their compression-molded counterpart was conducted.

This paper aims to investigate the effects of epoxy resin on the rheological and mechanical properties and water absorption rate of wood flour/high-density polyethylene (HDPE) composites (wood-plastic composite [WPC]).

The reactive mixing of various epoxy resins with 60 Wt.% wood flour and HDPE was carried out in a twin-screw extruder with a special screw element arrangement. Polyethylene-grafted maleic anhydride (MAPE) was used as a coupling agent to improve the interfacial interaction between wood flour, epoxy resin and HDPE.

The tensile, flexural and impact properties of the composites increased initially and then decreased with the increasing content of epoxy resin. The complex viscosity decreased with increasing epoxy resin content, but a trend reversal was observed at 8 Wt.% epoxy resin. The epoxy resin-modified wood-HDPE composites chemically coupled by MAPE showed minimal water absorption.

The cured epoxy resins impart high-aspect-ratio and plate-like polymeric fillers, affect the rheological behavior of the WPC and can also be oriented in a flow direction. Epoxy resin has good interaction with the cellulose structure of wood flour because of the polar functional groups within the cellulose.

This method provided a simple and practical solution to improve the performance of WPC.

The WPC modified by epoxy resin in this study had high performance in rheological and mechanical properties, and thus can be widely used for domestic, packaging and automotive applications.

Paints (surface coatings), primarily used to protect various substrates from the corroding action of acidic and alkaline substances, largely contain polymers as coating formulations. Examples of generally used polymers are: butadiene based (space), epoxy resins and silicone fluids (concrete vinyl polymers and polyurethanes (optical fibres) alkyds and acrylics (electronics) and polyester resins (wood, metal and fibre‐glass reinforcements). The binder‐pigment interaction controls important properties like hardness, flexibility, permeability, adhesion, gloss, and mechanical properties and contributes finally to the success or otherwise of the paint as a protective surface‐coating. Excellence of pigment dispersion and paint performance are thus intimately related.

The melt‐viscosity of shellac at various temperatures, the solution viscosity of shellac and the solution viscosity of several shellac‐based varnishes were investigated using a cone and plate rheometer. The study revealed information regarding yield stress (minimum force required for initiating flow) and thixotropic properties of shellac and shellac‐based materials. Such information will be useful for developing shellac‐based moulded articles and shellac‐based varnish compositions.

Material extrusion technology is considered to be an effective way to realize the accurate and integrated manufacturing of high-performance metal diamond tools with complex structures. The present work aims to report the G4 binder that can be used to create metal composite filament loading high concentrations of large diamond particles through comparative experiments.

The quality of filaments was evaluated by surface topography observation and porosity measurement. And the printability of filaments was further studied by the tensile test, rheological test, shear analysis and printing test.

The results show that the G4 binder exhibits the best capacity for loading diamonds among G1–G4. The L4 filament created with G4 has no defects such as pores, cracks and patterns on the surface and section, and has the lowest porosity, which is about 1/3 of the L1. Therefore, the diamond-containing composite filament based on G4 binder exhibits the best quality. On the other hand, the results of the tensile test of L5–L8 filaments reveal that as the diamond content increases from 10% to 30%, the tensile strength of the filament decreases by 29.52%, and the retention force coefficient decreases by 15.74%. This can be attributed to the formation of inefficient bonding areas of the clustered diamond particles inside the composite filament, which also leads to a weakening of the shear strength. Despite this, the results of the printing test show that the diamond-containing composite filament based on the G4 binder has reliable printability.

Therefore, the G4 binder is considered to solve the most critical first challenge in the development of diamond-containing filament.

The aim of this study is to develop a soy‐based cream cheese (SCC) with textural characteristics comparable to that of commercial dairy cream cheese (DCC) via the addition of microbial transglutaminase (MTG), soy protein isolate (SPI) and maltodextrin (MD).

Response surface methodology (RSM) was employed in this study to determine the effects of MTG, MD and SPI on firmness of SCC.

The second‐order model generated via RSM was significant with only a 9.76 per cent variation not explained by the model. The coefficient of regression revealed that MTG, MD and SPI showed significant linear effects (P<0.0001) on the firmness of SCC, while MTG and SPI showed significant quadratic effects. The model successfully predicted and developed a SCC model with similar firmness as that of DCC; via the combination of 2.57 per cent (w/w) of MTG, 19.69 per cent (w/w) of SPI and 19.69 per cent (w/w) of MD. Physicochemical analyses revealed that SCC possessed lower fat content, reduced saturated fatty acid and zero trans fat. Further rheological measurements revealed that SCC was more solid‐like at room temperature, but less elastic at refrigerated temperature compared to DCC. SEM and SDS‐PAGE analyses affirmed that the textural changes of SCC were attributed to MTG‐induced cross‐linking.

The research demonstrated that a non‐dairy cream cheese could be developed using soy. In addition, the SCC also contained better nutritional properties compared to its dairy counterpart.

In this study, polypropylene (PP)/polybutylene terephthalate (PBT) polyblend fibers that were melt spun at various blend ratios (5, 10, 20, 30 and 40 percent of the dispersed phase of the PBT) were prepared and the relation of the morphological, rheological and structural properties to dye uptake was investigated. The results show that the dye uptake of the PP/PBT polyblend fiber samples significantly increases when the dispersed phase content of the PBT is increased. An increase in the dispersed content of the PBT leads to interface improvement between the matrix and dispersed phase of the polyblend fibers, reduction in the crystallinity percentage and improvement in the adhesion bonds and active centers in the polyblend fibers for dye absorption. Positive deviation from the linear mixing rule observed in the melt viscosities is good evidence of the improvement in the morphology of the polyblend fiber samples.