Search results

The aim of this study was to prove that radio-frequency (RF) energy with 13.56 MHz can be used for heating building structures in a controlled manner exploiting the advantage that homogeneous heating with sufficient penetration depths can be achieved.

Because parallel electrodes on both sides of the heated structure cannot be used in many practical applications, two special electrode designs have been developed by modeling the field distribution and energy absorption and by carrying out test experiments to validate the simulation results.

One solution is based on a two-dimensional surface capacitor providing certain penetration depths and being especially suitable for treating thin structures such as wooden parquet floor. Such an arrangement can be particularly used for pest control even when sensitive surfaces have to be protected. The other solution uses a capacitive coupling between the grounded shielding and an electrode or an equivalent structure (e.g. moist soil) at the other side of the masonry to establish a sufficiently strong electrical field between a “hot” electrode on the side of the shielding and the coupled rear electrode.

Both solutions significantly enhance the application potential of RF heating.

Additive manufacturing (AM) of thermoplastic polymers for powder bed fusion processes typically requires each layer to be fused before the next can be deposited. The purpose of this paper is to present a volumetric AM method in the form of deeply penetrating radio frequency (RF) radiation to improve the speed of the process and the mechanical properties of the polymer parts.

The focus of this study was to demonstrate the volumetric fusion of composite mixtures containing polyamide (nylon) 12 and graphite powders using RF radiation as the sole energy source to establish the feasibility of a volumetric AM process for thermoplastic polymers. Impedance spectroscopy was used to measure the dielectric properties of the mixtures as a function of increasing graphite content and identify the percolation limit. The mixtures were then tested in a parallel plate electrode chamber connected to an RF generator to measure the heating effectiveness of different graphite concentrations. During the experiments, the surface temperature of the doped mixtures was monitored.

Nylon 12 mixtures containing between 10% and 60% graphite by weight were created, and the loss tangent reached a maximum of 35%. Selective RF heating was shown through the formation of fused composite parts within the powder beds.

The feasibility of a novel volumetric AM process for thermoplastic polymers was demonstrated in this study, in which RF radiation was used to achieve fusion in graphite-doped nylon powders.

Recent work has demonstrated the possibility of selectively sintering polymer powders with radio frequency (RF) radiation as a means of rapid, volumetric additive manufacturing. Although RF radiation can be used as a volumetric energy source, non-uniform heating resulting from the sample geometry and electrode configuration can lead to adverse effects in RF-treated samples. This paper aims to address these heating uniformity issues by implementing a computational design strategy for doped polymer powder beds to improve the RF heating uniformity.

Two approaches for improving the RF heating uniformity are presented with the goal of developing an RF-assisted additive manufacturing process. Both techniques use COMSOL Multiphysics® to predict the temperature rise during simulated RF exposure for different geometries. The effectiveness of each approach is evaluated by calculating the uniformity index, which provides an objective metric for comparing the heating uniformity between simulations. The first method implements an iterative heuristic tuning strategy to functionally grade the electrical conductivity within the sample. The second method involves reorienting the electrodes during the heating stage such that the electric field is applied in two directions.

Both approaches are shown to improve the heating uniformity and predicted part geometry for several test cases when applied independently. However, the greatest improvement in heating uniformity is demonstrated by combining the approaches and using multiple electrode orientations while functionally grading the samples.

This work presents an innovative approach for overcoming RF heating uniformity issues to improve the resulting part geometry in an RF-assisted, volumetric additive manufacturing method.

This paper reviews and compares the methods of kinetic heat simulation which may be used simultaneously with normal loading in structural tests of aircraft or components. Basic data on the quantities involved in and the limitations of the various techniques are given. An extensive bibliography of current literature on heat technology is provided.

Discusses applications of microwave and radio frequency technology in the food industry. It is used for heating – either for more rapid drying than conventional technology or to assist baking – it allows significant economies. Describes research on bread and biscuit baking.

The purpose of this paper is to focus on applications related to the hyperthermia treatment of cancer, with heating imposed either by a laser in the near-infrared range or by radiofrequency waves. The particle filter algorithms are compared in terms of computational time and solution accuracy.

The authors extend the analyses performed in their previous works to compare three different algorithms of the particle filter, as applied to the hyperthermia treatment of cancer. The particle filters examined here are the sampling importance resampling (SIR) algorithm, the auxiliary sampling importance resampling (ASIR) algorithm and Liu & West’s algorithm.

Liu & West’s algorithm resulted in the largest computational times. On the other hand, this filter was shown to be capable of dealing with very large uncertainties. In fact, besides the uncertainties in the model parameters, Gaussian noises, similar to those used for the SIR and ASIR filters, were added to the evolution models for the application of Liu & West’s filter. For the three filters, the estimated temperatures were in excellent agreement with the exact ones.

This work may help medical doctors in the future to prescribe treatment protocols and also opens the possibility of devising control strategies for the hyperthermia treatment of cancer.

The natural solution to couple the uncertain results from numerical simulations with the measurements that contain uncertainties, aiming at the better prediction of the temperature field of the tissues inside the body, is to formulate the problem in terms of state estimation, as performed in this work.

This bibliography is offered as a practical guide to published papers, conference proceedings papers and theses/dissertations on the finite element (FE) and boundary element (BE) applications in different fields of biomechanics between 1976 and 1991. The aim of this paper is to help the users of FE and BE techniques to get better value from a large collection of papers on the subjects. Categories in biomechanics included in this survey are: orthopaedic mechanics, dental mechanics, cardiovascular mechanics, soft tissue mechanics, biological flow, impact injury, and other fields of applications. More than 900 references are listed.

This paper aims to introduce and illustrate a computational technique capable of determining the geometry and complex permittivity of a supplementary dielectric insert making distributions of microwave-induced dissipated power within the processed material as uniform as possible.

The proposed technique is based on a 3D electromagnetic model of the cavity containing both the processed material and the insert. Optimization problem is formulated for design variables (geometrical and material parameters of the insert) identified from computational tests and an objective function (the relative standard deviation [RSD]) introduced as a metric of the field uniformity. Numerical inversion is performed with the method of sequential quadratic programming.

Functionality of the procedure is illustrated by synthesis of a dielectric insert in an applicator for microwave fixation. Optimization is completed for four design variables (two geometrical parameters, dielectric constant and the loss factor of the insert) with 1,000 points in the database. The best three optimal solutions provide RSD approximately 20 per cent, whereas for the patterns corresponding to all 1,000 non-optimized (randomly chosen) sets of design variables this metric is in the interval from 27 to 136 per cent with the average of 78 per cent.

As microwave thermal processing is intrinsically inhomogeneous and the heating time is not a part of the underlying model, the procedure is able to lead only to a certain degree of closeness to uniformity and is intended for applications with high heating rates. The initial phase of computational identification of design variables and their bounds is therefore very important and may pre-condition the “quality” of the optimal solution. The technique may work more efficiently in combination with advanced optimization techniques dealing with “smart” (rather than random) generation of the data; for the use with more general microwave heating processes characterized by lower heating rates, the technique has to use the metric of non-uniformity involving temperature and heating time.

While the procedure can be used for computer-aided design (CAD) of microwave applicators, a related practical limitation may emerge from the fact that the material with particular complex permittivity (determined in the course of optimization) may not exist. In such cases, the procedure can be rerun for the constant values of material parameters of the available medium mostly close to the optimal ones to tune geometrical parameters of the insert. Special manufacturing techniques capable of producing a material with required complex permittivity also may be a practical option here.

Non-uniformity of microwave heating remains a key challenge in the design of many practical applicators. This paper suggests a concept of a practical CAD and outlines corresponding computational procedure that could be used for designing a range of applied systems with high heating rates.

Modern thermal and non-thermal pretreatment techniques, namely, enzymatic treatment, gas phase plasma treatment and ohmic heating have become more pronounced over conventional techniques for enhanced coloured phytochemicals (pigments) extraction. Presently, numbers of pretreatment techniques are available with some unique feature. It is difficult to choose best pretreatment method to be employed for phytochemicals extraction from different sources. Therefore, this paper aims to discuss different modern pretreatment techniques for extraction with their potential results over conventional techniques.

Research and review articles targeting to the thermal and non-thermal pretreatment techniques were collected from Google Scholar. The required information has been tabulated and discussed which included qualities of modern pretreatment techniques over conventional techniques, phytochemical extraction and best pretreatment methods for optimized results.

Every pre-treatment has its own advantages and disadvantages for a particular phytochemical and its extraction from various sources. Enzymes can be used in combinations to enhance final yield like extraction of carotenoids (pectinase, cellulase and hemicellulase) from chillies and lycopene (pectinase and cellulase) from tomato. Utilization of each method depends upon many factors such as source of pigment, cost and energy consumption. CO₂ pretreatment gives good results for carotenoid extraction from algae sources. Ohmic heating can yield high anthocyanin content. Modifications in conventional blanching has reduced final waste and improvised the properties of pigment.

This study comprises collective information regarding modern pre-treatment for extraction over conventional pre-treatments. The study also covers future trends and certain new hybrid approaches which are still less flourished.

Millets are ancient grains, following wheat, that have been a fundamental source of human sustenance. These are nutrient-rich small-seeded grains that have gained prominence and admiration globally due to their super resilience in diverse climates and significant nutritional benefits. As millets are renowned for their nutritional richness, the demand for millet-based products increases. Hence, this paper aims in identifying the growing need for innovative processing techniques that not only preserve their nutritional content but also extend their shelf life.

In traditional times, heat was the only means of cooking and processing of the foods, but the amount of damage they used to cause to the sensorial and nutritional properties was huge. Millets’ sensitivity toward heat poses a challenge, as their composition is susceptible to disruption during various heat treatments and manufacturing processes. To cater to this drawback while ensuring the prolonged shelf life and nutrient preservation, various innovative approaches such as cold plasma, infrared technology and high hydrostatic pressure (HPP) processing are being widely used. These new methodologies aim on inactivating the microorganisms that have been developed within the food, providing the unprocessed, raw and natural form of nutrients in food products.

Among these approaches, nonthermal technology has emerged as a key player that prioritizes brief treatment periods and avoids the use of high temperatures. Nonthermal techniques (cold plasma, infrared radiation, HPP processing, ultra-sonication and pulsed electric field) facilitate the conservation of millet’s nutritional integrity by minimizing the degradation of heat-sensitive nutrients like vitamins and antioxidants. Acknowledging the potential applications and processing efficiency of nonthermal techniques, the food industry has embarked on substantial investments in this technology. The present study provides an in-depth exploration of the array of nonthermal technologies used in the food industry and their effects on the physical and chemical composition of diverse millet varieties.

Nonthermal techniques, compared to conventional thermal methods, are environmentally sound processes that contribute to energy conservation. However, these conveniences are accompanied by challenges, and this review not only elucidates these challenges but also focuses on the future implications of nonthermal techniques.