Search results

1 – 10 of 778
Article
Publication date: 2 August 2013

Slawomir Kubacki, Jacek Rokicki and Erik Dick

Applicability of two k‐ω hybrid RANS/LES and a k‐ω RANS models is studied for simulation of round impinging jets at nozzle‐plate distance H/D=2 with Reynolds number 70000, H/D=2…

333

Abstract

Purpose

Applicability of two k‐ω hybrid RANS/LES and a k‐ω RANS models is studied for simulation of round impinging jets at nozzle‐plate distance H/D=2 with Reynolds number 70000, H/D=2 with Reynolds number 5000 and H/D=10 with Reynolds number 5000 (D is the nozzle exit diameter). The aim is to verify two concepts of unified hybrid RANS/LES formulations, one of DES (Detached Eddy Simulation) type and one of LNS (Limited Number Scales) type in analysis of impinging jet flow and heat transfer. The grid resolution requirements are also discussed.

Design/methodology/approach

The simulations are performed with two k‐ω based hybrid RANS/LES models of very different nature, one of DES type and one of LNS type, and the RANS k‐ω model. For the lower Reynolds number (5000), also dynamic Smagorinsky LES is done. Both hybrid model formulations converge to the same RANS k‐ω model in the near‐wall region and have the same Smagorinsky limit on fine isotropic grids in the LES mode of the hybrid models.

Findings

With the hybrid RANS/LES models, improved fluid flow and heat transfer results are obtained compared to RANS, in the impact region and in the developing wall‐jet region. For accurate predictions at low nozzle‐plate distance, where the impact region is in the core of the jet, it is necessary to sufficiently resolve the formation and breakup of the near‐wall vortices in the jet impingement region and the developing wall‐jet region, as these determine largely the level of fluctuating velocity and the heat transfer. This requires high grid resolution for high Reynolds number, while the grid resolution requirements stay modest for low Reynolds number.

Originality/value

The paper demonstrates that two formulations of hybrid RANS/LES models of different nature, one of DES type and one of LES type, lead to equivalent results. Consistency has been guaranteed in the sense that the RANS limit of both models is the same and that the LES limit on fine, isotropic, grids is the same. In the intermediate range, however, the repartition into resolved and modelled fluctuations may differ considerably.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 23 no. 6
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 19 November 2021

M. R. Nived, Bandi Sai Mukesh, Sai Saketha Chandra Athkuri and Vinayak Eswaran

This paper aims to conduct, a detailed investigation of various Reynolds averaged Navier–Stokes (RANS) models to study their performance in attached and separated flows. The…

Abstract

Purpose

This paper aims to conduct, a detailed investigation of various Reynolds averaged Navier–Stokes (RANS) models to study their performance in attached and separated flows. The turbulent flow over two airfoils, namely, National Advisory Committee for Aeronautics (NACA)-0012 and National Aeronautics and Space Administration (NASA) MS(1)-0317 with a static stall setup at a Reynolds number of 6 million, is chosen to investigate these models. The pre-stall and post-stall regions, which are in the range of angles of attack 0°–20°, are simulated.

Design/methodology/approach

RANS turbulence models with the Boussinesq approximation are the most commonly used cost-effective models for engineering flows. Four RANS models are considered to predict the static stall of two airfoils: Spalart–Allmaras (SA), Menter’s kω shear stress transport (SST), k – kL and SA-Bas Cakmakcioglu modified (BCM) transition model. All the simulations are performed on an in-house unstructured-grid compressible flow solver.

Findings

All the turbulence models considered predicted the lift and drag coefficients in good agreement with experimental data for both airfoils in the attached pre-stall region. For the NACA-0012 airfoil, all models except the SA-BCM over-predicted the stall angle by 2°, whereas SA-BCM failed to predict stall. For the NASA MS(1)-0317 airfoil, all models predicted the lift and drag coefficients accurately for attached flow. But the first three models showed even further delayed stall, whereas SA-BCM again did not predict stall.

Originality/value

The numerical results at high Re obtained from this work, especially that of the NASA MS(1)-0317, are new to the literature in the knowledge of the authors. This paper highlights the inability of RANS models to predict the stall phenomenon and suggests a need for improvement in modeling flow physics in near- and post-stall flows.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 32 no. 4
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 3 July 2017

Gaurav Kumar, Ashoke De and Harish Gopalan

Hybrid Reynolds-averaged Navier–Stokes large eddy simulation (RANS-LES) methods have become popular for simulation of massively separated flows at high Reynolds numbers due to…

Abstract

Purpose

Hybrid Reynolds-averaged Navier–Stokes large eddy simulation (RANS-LES) methods have become popular for simulation of massively separated flows at high Reynolds numbers due to their reduced computational cost and good accuracy. The current study aims to examine the performance of LES and hybrid RANS-LES model for a given grid resolution.

Design/methodology/approach

For better assessment and contrast of model performance, both mean and instantaneous flow fields have been investigated. For studying instantaneous flow, proper orthogonal decomposition has been used.

Findings

Current analysis shows that hybrid RANS-LES is capable of achieving similar accuracy in prediction of both mean and instantaneous flow fields at a very coarse grid as compared to LES.

Originality/value

Focusing mostly on the practical applications of computation, most of the attention has been given to the prediction of one-point flow statistics and little consideration has been put to two-point statistics. Here, two-point statistics has been considered using POD to investigate unsteady turbulent flow.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 27 no. 7
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 11 October 2021

Axel Probst and Stefan Melber-Wilkending

The paper aims to assess the feasibility of locally turbulence-resolving flow simulations for a high-lift aircraft configuration near maximum lift. It addresses the aspects of…

Abstract

Purpose

The paper aims to assess the feasibility of locally turbulence-resolving flow simulations for a high-lift aircraft configuration near maximum lift. It addresses the aspects of proper grid design and explores the ability of the hybrid turbulence model and the numerical scheme to automatically select adequate modes in different flow regions. By comparison with experimental and numerical reference data, the study aims to provide insights into the predictive potential of the method for high-lift flows.

Design/methodology/approach

The paper applies numerical flow simulations using well-established tools such as DLR's (German Aerospace Center) TAU solver and the SOLAR grid generator to study “Improved Detached Delayed Eddy Simulations” of the Japan Aerospace Exploration Agency (JAXA) Standard Model at two angles of attack near maximum lift. The simulations apply a hybrid low-dissipation low-dispersion scheme and implicit time stepping with adequate temporal resolution. The simulation results, including pressure distributions and near-wall flow patterns, are assessed by comparison with experimental wind-tunnel data.

Findings

Apart from demonstrating the general feasibility of the numerical approach for complex high-lift flows, the results indicate somewhat improved maximum lift predictions compared to the Spalart–Allmaras model, which is consistent with a slightly closer agreement with measured pressure distributions and oil-flow pictures. However, the expected lift breakdown caused by an increasing inboard separation in the experiment is not well captured.

Originality/value

The study not only provides new insight into the feasibility and promising potential of hybrid turbulence-resolving methods for relevant high-lift aircraft flows but also indicates the need for further research on the numerical sensitivities, such as grid resolution or flow initialization.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 32 no. 4
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 4 September 2017

Anton Stephan, Frank Holzäpfel and Stefan Zholtovski

This study aims to investigate the effect of gusts on aircraft wake vortices. Aircraft wake vortices present a potential risk to following aircraft, particularly during final…

Abstract

Purpose

This study aims to investigate the effect of gusts on aircraft wake vortices. Aircraft wake vortices present a potential risk to following aircraft, particularly during final approach and landing, as wake vortices may remain in the flight corridor for a long time. Wind and turbulence are key factors that influence the wake vortex evolution and the wake vortex generation in the aircraft. Flying through a gust influences the wake vortex roll-up process and its evolution. Note that vertical and lateral gusts may affect counter-rotating wake vortices differently. Both vortices influence each other by inducing a downward velocity. Disturbances may therefore lead to local vortex tilting and later to a complex three-dimensional deformation. This work uses two different hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (RANS-LES) approaches to investigate the effect of gusts on wake vortex evolution. In a one-way coupling, a pre-calculated RANS velocity field of the aircraft’s near-field is being swept through an LES domain. The effect of a sine gust on the turbulent wake is modeled by manipulating the RANS-field accordingly. As a more sophisticated approach, the concept of a two-way coupling is being presented. Here an LES solver is bi-directionally coupled with an unsteady RANS (URANS) solver, exchanging values at every physical time step of the simulation.

Design/methodology/approach

A one-way coupling approach of the LES code MGLET and the RANS code TAU is presented to simulate the gust effect on aircraft wake vortices. Additionally, the concept of the two-way coupling of these two codes incorporating a coupling module.

Findings

The gust effect of wake vortices subjected to a crosswind can be simulated. The vortex physics is analyzed. Unexpected behavior like fast upwind vortex decay is revealed.

Practical implications

The understanding of the aircraft wake vortex physics during landing provides valuable information for wake vortex advisory systems.

Originality/value

The effect of gust on wake vortices during and after landing has not been studied so far. The hybrid one-way coupling approach, as well as the concept of the two-way coupling, are relatively new.

Details

Aircraft Engineering and Aerospace Technology, vol. 89 no. 5
Type: Research Article
ISSN: 1748-8842

Keywords

Article
Publication date: 4 December 2017

Chunbao Liu, Weiyang Bu, Dong Xu, Yulong Lei and Xuesong Li

This paper aims to improve performance prediction and to acquire more detailed flow structures so as to analyze the turbulence in complex rotor-stator flow.

Abstract

Purpose

This paper aims to improve performance prediction and to acquire more detailed flow structures so as to analyze the turbulence in complex rotor-stator flow.

Design/methodology/approach

Hydraulic retarder as typical fluid machinery was numerically investigated by using hybrid Reynolds-averaged Navier–Stokes (RANS)/large eddy simulation (LES) models CIDDES Algebraic Wall-Modeled Large Eddy Simulation (LES) (WMLES) S-Ω and dynamic hybrid RANS/LES (DHRL). The prediction results were compared and analyzed with a RANS model shear stress transport (SST) k-omega which was a recommended choice in engineering.

Findings

The numerical results were verified by experiment and indicated that the predicted values for three hybrid turbulence models were more accurate. Then, the transient flow field was further analyzed visually in terms of turbulence statistics, Reynolds number, pressure-streamline, vortex structure and eddy viscosity ratio. The results indicated that HRL approaches could capture unsteady flow phenomena.

Practical implications

This study achieves both in performance prediction improvement and better flow mechanism understanding. The computational fluid dynamics (CFD) could be used instead of flow visualization to a certain extent. The improved CFD method, the fine computational grid and the reasonable simulation settings jointly enhance the application of CFD in the rotor-stator flow.

Originality/value

The improvement was quite encouraging compared with the reported literatures, contributing to the CFD playing a more important role in the flow machinery. DHRL provided the detailed explanation of flow transport between rotor and stator, which was not reported before. Through it, the flow mechanism can be better understood.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 27 no. 12
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 7 March 2016

Nikita Ageev and Alexander Pavlenko

This study aims to decrease the aerodynamic drag of the body of revolution at supersonic speeds. Supersonic area rule is widely used in modern supersonic aircraft design. Further…

Abstract

Purpose

This study aims to decrease the aerodynamic drag of the body of revolution at supersonic speeds. Supersonic area rule is widely used in modern supersonic aircraft design. Further reduction of the aerodynamic drag is possible in the framework of Euler and Reynolds averaged Navier–Stokes (RANS) equations. Sears–Haack body of revolution shape variation, which decreased its aerodynamic drag in compressible inviscid and viscous gas flow at Mach number of 1.8 under constraint of the volume with lower bound equal to volume of initial body, was numerically investigated.

Design/methodology/approach

Calculations were carried out in two-dimensional axisymmetric mode in the framework of Euler and RANS with SST model with compressibility correction equations at structured multiblock meshes. Variation of the radius as function of the longitudinal coordinate was given as a polynomial third-order spline through five uniformly distributed points. Varied parameters were increments of the radius of the body at points that defined spline. Drag coefficient was selected as an objective function. Parameter combinations corresponding to the objective function minimum under volume constraint were obtained by mixed-integer sequential quadratic programming at second-order polynomial response surface and IOSO algorithm.

Findings

Improving variations make front part of the body become slightly blunted, transfer part of volume from front part of the body to back part and generate significant back face. In the framework of RANS, the best variation decreases aerodynamic drag by approximately 20 per cent in comparison with Sears–Haack body.

Practical implications

The results can be applied for the aerodynamic design of the bullets and projectiles. The second important application is knowledge of the significance of the difference between linearized slender body theory optimization results and optimization results obtained by modern computational fluid dynamics (CFD) optimization techniques.

Social implications

Knowledge about the magnitude of the difference between linearized slender body theory optimization results and optimization results obtained by modern CFD optimization techniques can stimulate further research in related areas.

Originality/value

The optimization procedure and optimal shapes obtained in the present work are directly applicable to the design of small aerodynamic drag bodies.

Details

Aircraft Engineering and Aerospace Technology: An International Journal, vol. 88 no. 2
Type: Research Article
ISSN: 1748-8842

Keywords

Article
Publication date: 4 September 2017

Marcello Righi

The quality of aeroelastic predictions strongly depends on the quality of aerodynamic predictions. At the boundary of a typical flight envelope, special flow conditions may arise…

Abstract

Purpose

The quality of aeroelastic predictions strongly depends on the quality of aerodynamic predictions. At the boundary of a typical flight envelope, special flow conditions may arise, which challenge the conventional Reynolds-averaged Navier–Stokes (RANS) approach beyond reasonable limits.

Design/methodology/approach

Test Case 3 of the Second AIAA Aeroelastic Prediction Workshop is a representative test case, where the flow over a supercritical wing separates downstream of the shock waves and generates large turbulent lengthscales.

Findings

In this study, RANS predictions are compared to those obtained in this particular test case with the more sophisticated hybrid RANS–large eddy simulation (LES) approach, in particular with the Spalart–Allmaras–delayed detached eddy simulation model. Results are indeed closer to experimental data.

Originality/value

However, the costs associated with this approach are much higher. It is argued that adopting hybrid RANS–LES modelling is not a simple model switch.

Details

Aircraft Engineering and Aerospace Technology, vol. 89 no. 5
Type: Research Article
ISSN: 1748-8842

Keywords

Article
Publication date: 29 April 2014

Wei Wang, Spiridon Siouris and Ning Qin

The purpose of this article is to present numerical investigations of flow control with piezoelectric actuators on a backward facing step (BFS) and fluidic vortex generators on a…

Abstract

Purpose

The purpose of this article is to present numerical investigations of flow control with piezoelectric actuators on a backward facing step (BFS) and fluidic vortex generators on a NACA0015 aerofoil for the reattachment and separation control through the manipulation of the Reynolds stresses.

Design/methodology/approach

The unsteady flow phenomena associated with both devices are simulated using Spalart–Allmaras-based hybrid Reynolds averaged Navier-Stokes (RANS)/large eddy simulation (LES) models (detached eddy simulation (DES), delayed detached eddy simulation (DDES) and improved delayed detached eddy simulation (IDDES)), using an in-house computational fluid dynamics (CFD) solver. Results from these computations are compared with experimental observations, enabling their reliable assessment through the detailed investigation of the Reynolds stresses and also the separation and reattachment.

Findings

All the hybrid RANS/LES methods investigated in this article predict reasonable results for the BFS case, while only IDDES captures the separation point as measured in the experiments. The oscillating surface flow control method by piezoelectric actuators applied to the BFS case demonstrates that the Reynolds stresses in the controlled case decrease, and that a slightly nearer reattachment is achieved for the given actuation. The fluidic vortex generators on the surface of the NACA0015 case force the separated flow to fully reattach on the wing. Although skin friction is increased, there is a significant decrease in Reynolds stresses and an increase in lift to drag ratio.

Originality/value

The value of this article lies in the assessment of the hybrid RANS/LES models in terms of separation and reattachment for the cases of the backward-facing step and NACA0015 wing, and their further application in active flow control.

Details

Aircraft Engineering and Aerospace Technology: An International Journal, vol. 86 no. 3
Type: Research Article
ISSN: 0002-2667

Keywords

Article
Publication date: 19 February 2024

Xiang Shen, Kai Zeng, Liming Yang, Chengyong Zhu and Laurent Dala

This paper aims to study passive control techniques for transonic flow over a backward-facing step (BFS) using square-lobed trailing edges. The study investigates the efficacy of…

Abstract

Purpose

This paper aims to study passive control techniques for transonic flow over a backward-facing step (BFS) using square-lobed trailing edges. The study investigates the efficacy of upward and downward lobe patterns, different lobe widths and deflection angles on flow separation, aiming for a deeper understanding of the flow physics behind the passive flow control system.

Design/methodology/approach

Large Eddy Simulation and Reynolds-averaged Navier–Stokes were used to evaluate the results of the study. The research explores the impact of upward and downward patterns of lobes on flow separation through the effects of different lobe widths and deflection angles. Numerical methods are used to analyse the behaviour of transonic flow over BFS and compared it to existing experimental results.

Findings

The square-lobed trailing edges significantly enhance the reduction of mean reattachment length by up to 80%. At Ma = 0.8, the up-downward configuration demonstrates increased effectiveness in reducing the root mean square of pressure fluctuations at a proximity of 5-step height in the wake region, with a reduction of 50%, while the flat-downward configuration proves to be more efficient in reducing the root mean square of pressure fluctuations at a proximity of 1-step height in the near wake region, achieving a reduction of 71%. Furthermore, the study shows that the up-downward configuration triggers early spanwise velocity fluctuations, whereas the standalone flat-downward configuration displays less intense crosswise velocity fluctuations within the wake region.

Practical implications

The findings demonstrate the effectiveness of square-lobed trailing edges as passive control techniques, showing significant implications for improving efficiency, performance and safety of the design in aerospace and industrial systems.

Originality/value

This paper demonstrates that the square-lobed trailing edges are effective in reducing the mean reattachment length and pressure fluctuations in transonic conditions. The study evaluates the efficacy of different configurations, deflection angles and lobe widths on flow and provides insights into the flow physics of passive flow control systems.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 0961-5539

Keywords

1 – 10 of 778