Search results

One of the low-cost minerals that can be used as reinforcing filler in polymer industry is pumice powder. Pumice is a highly porous volcanic glass formed during explosive eruptions. This pumice has received significant interest because of its large surface area with various polar groups and can be processed easily.

This study is carried out to investigate the effect of partial replacement of silica (as traditional filler) by naturally occurring pumice powder to improve the thermal and mechanical properties of nitrile butadiene rubber cured with electron beam radiation (doses from 25 to 150 kGy).

The results indicated that the addition of pumice powder increase the tensile strength at lower doses up to 75 kGy (especially at concentration of 5 phr). Besides, an improvement in the thermal stability was attained with the addition of pumice powder.

Pumice powder is volcanic-based alumina and silica which is mainly composed of SiO₂. It has porous structure which is formed by dissolved gases precipitated during the cooling as the lava hurtles through air. Due to its porous structure, it has low density and high thermal insulation. It also has high temperature and chemical resistance, for these reasons it became preferable material to be used as filler in the plastic and rubber industry.

Due to problems experienced at the deburring stage of drilled 0·013 in. diameter holes, where the holes became blocked with deburring brush fibres, it was necessary to replace the use of traditional deburring techniques for the preparation of these drilled holes prior to electroless copper plating. In order to achieve this, a jet pumice machine was purchased and trials were conducted using various grades of pumice powder and different machine parameters. The purpose of these trials was to determine the optimum machine parameters for the task, such that burr‐free hole peripheries were achieved in conjunction with a surface finish suitable for electroless copper plating prior to dry film lamination.

The causes that have produced the revolting state of affairs in the matter of the “canned” food and meat scandals in the United States are of interest chiefly to the student of social pathology. The fact of the existence of the abuses referred to, however, appeals to us in this country in a different and more practical way, and demands careful consideration.

A comparative study on methods for cleaning copper‐clad boards with abrasive slurries is presented. A number of methods are analysed in detail; the conclusions indicate that brush scrubbing with abrasive slurries offers a wider processing window, whereas jet scrubbing is less ‘forgiving’ for the small/medium‐sized manufacturers where more handling of the material is necessary due to reduced automation. For the larger high volume manufacturers of printed circuit boards with higher levels of automation and tighter process control no significant yield differences were found.

Although in recent years RBH has extended its activities into a wide range of chemicals and oil products, nevertheless, mineral extenders and fillers remain a very important interest of the business. The range of products handled includes:—

This study aims to use porous concrete and mineral adsorbents (additives) for reducing the quantity and improving the quality of urban runoff.

The effects of adding mineral adsorbents and fine grains to porous concrete is tested for increasing its performance in improving the quality of urban runoff. Two levels of sand (10 and 20 per cent) and 5, 10 and 15 per cent of zeolite, perlite, LECA and pumice were added to the porous concrete. Unconfined compressive strength, hydraulic conductivity (permeability) and porosity of the porous concrete specimens were measured. Some of the best specimens were selected for testing the improvement of runoff quality. A rainfall simulator was designed and the quality of the runoff was investigated for changes in electrical conductivity (EC), total suspended solids (TSS), total dissolved solids (TDS) and chemical oxygen demand (COD).

The results of this study showed that compressive strength of the porous concrete was increased by adding fine grains to the concrete mixture. Fine grains decreased the permeability and porosity of the samples. Zeolite had the highest compressive strength. Samples having pumice own maximum permeability. Samples which had perlite, had the least compressive strength and permeability. Because of the fast flow of runoff water in the porous slab and its low thickness, sufficient time was not provided for effective functioning of the additives, and the removal percentage of the pollution parameters was low.

Porous concrete can ameliorate both quantity and quality of the urban runoff.

The purpose of this paper is to investigate the influence of silver nanoparticle additions on the wetting properties of Sn‐Ag‐Cu (SAC) solder paste. In this investigation, the basic solder paste contained 85 wt.% of commercial Sn 96.5 Ag 3 Cu 0.5 powder (with the particle sizes in the range of 20‐38 μm) and 15 wt.% of self‐prepared middle activated rosin flux. To this paste was added 0.5, 1, 2 and 4 wt.% of self‐prepared silver nano‐powders of different grain sizes (from 9 to 138 nm). After the pastes had stabilized, their wetting properties were tested. The main goal of these investigations was to improve the wetting properties of SAC solder paste and to find correlations between the results of the wetting of solder paste with nanoparticles on the copper substrate with the microstructure of the solder joints.

The following methods were applied for the wetting solder paste investigation: spreading on the copper substrate, contact angle measurement on the copper and wetting on a FR‐4 laminate double sided with an 18‐μm thick copper foil. The investigations were performed at temperatures of 220, 230, 240 and 250°C. Cross‐sectioning was performed on the solder paste after reflow on the copper substrate. For the microstructural analysis of the “nano” modified solder joints obtained at 250°C, standard metallographic procedures were applied. Changes in the microstructure, the thickness of the inter‐metallic compounds (IMCs) and their chemical compositions were observed by means of scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS).

As expected, a higher silver nanoparticle addition to the SAC solder paste resulted in better wetting properties on copper. The results indicated the possibility of an improvement of the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature. An improvement was also observed in the wettability with a decrease in the silver nanoparticle grain size. Also, the wettability proceeded at a lower temperature (20°C lower) than that for the SAC paste, without the nano‐additives. For the 4 per cent silver nanoparticle addition, Ag₃Sn star‐like IMCs were also found, which grew with the lowering of the silver nanoparticle grain size.

Further studies are necessary for confirmation of the practical application, especially of the mechanical properties, as well as the reliability properties of the solder joints, for the chosen solder paste with silver nanoparticles.

Taking into account the wetting data, the best results of the “nano” SAC solder pastes were obtained for the highest addition of the silver nanoparticles. It was found that the spreading on copper was higher and the contact angles were lower for the SAC solder paste with 4 per cent (by wt.) of 138‐nm grain size silver nanoparticles. A comparison of SAC solder pastes with a 4 per cent silver nanoparticle addition but of a different grain size (138‐9 nm), suggested a further improvement in wetting properties with lowering of the silver nanoparticle grain size. The results suggested the possibility of an improvement in the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature.

Spreading, wetting and contact angle measurement methods were used for the wetting determination of the SAC solder paste with the silver nanoparticles on copper under the same temperature conditions. Also, the microstructure of the solder joints obtained at 250°C was determined with the use of SEM and EDS methods. The results obtained made it possible to draw conclusions regarding the correlation between the output of the wetting results and the amount and the grain size of the added silver nanoparticles, and also the microstructure and thickness of the IMCs of the “nano” solder joints.

The purpose of this paper is to study the manufacturing of SAC 305 solder paste with multiwall carbon nanotubes (MWCNT) before and after structure modification and also to investigate the added carbon nanotubes' influence on the technological properties and the microstructure of “nano” solder pastes. This work is a continuation of similar previous studies of SAC solder pastes with silver nanopowder additions.

The authors applied functionalization and esterification methods for the structural modification of the carbon nanotubes. The “nano” solder paste preparation was performed with the use of a two‐stage method of carbon nanotube dispersion in “own‐manufactured” SAC 305 solder paste. To determine the technological properties of the “nano” solder paste, slump, solder ball, wetting and spreading tests were applied according to the existing standards. Standard metallographic procedures were applied for microstructural analysis.

As expected on the basis of the previous studies of SAC solder pastes with silver nanopowders, positive results were obtained for the own‐manufactured SAC 305 solder paste with carbon nanotubes by applying the dispersion method. Also applied were functionalization and esterification methods, whose results showed microstructural changes in the carbon nanotubes. The “nano” SAC solder pastes showed a positive influence on the slump properties, compared to the basic SAC solder paste. The authors proved a negative influence of the carbon nanotubes' addition (dependent on their concentration) on the spreading and wetting of the SAC solder paste on a copper substrate, which provoked the non‐wetting and dewetting phenomena. A slight improvement was observed for the “nano” SAC solder pastes with modified carbon nanotubes. The carbon nanotubes' presence in the solder paste showed a positive effect on the growth reduction of the IMCs' thickness, which depended on the type.

The authors intend to verify the reinforcement effect of the alloys with carbon nanotubes suggested in the literature (the aim of Part II). For this purpose, an assembly process with RC electronic elements on PCBs with Ni/Au and SAC (HASL) finishes will be performed, with the use of the SAC 305 solder paste with modified carbon nanotubes, for the purpose of reflow soldering. Next, measurements of the mechanical strength of the solder joints and their microstructures will be conducted.

It is suggested that further studies of the mechanical properties and the reliability of solder joints are necessary for the practical implementation of the “nano” SAC solder pastes, but taking into account the wetting data, the investigation should be performed only for “nano” pastes with the lowest additions of modified carbon nanotubes.

The paper demonstrates a method of “nano” solder paste preparation by means of a two‐stage dispersion of carbon nanotubes in the own‐manufactured SAC 305 solder paste and a comparison study of the properties of “nano” pastes with the basic SAC solder paste.

The purpose of this paper is to present the modeling of statistical variation of experimental data using the design of experiments method to optimize the formulation of a high performance concrete (HPC) using materials that are locally available in Algeria. For this, two mineral additions (natural pozzolana and limestone filler [LF]) were used. Both additions are added by substitution of cement up to 25%. To better appreciate the effect of replacing a part of cement by natural pozzolana and LF and to optimize their combined effect on the characteristics of HPC, an effective analytical method is therefore needed to reach the required objective.

The experimental part of the study consisted of substituting a portion of cement by various proportions of these additions to assess their effects on the physico-mechanical characteristics of HPC. A mixture design with three factors and five levels was carried out. The JMP7 software was used to provide mathematical models for the statistical variation of measured values and to perform a statistical analysis. These models made it possible to show the contribution of the three factors and their interactions in the variation of the response.

The mixture design approach made it possible to visualize the influence of LF and pozzolanic filler (PF) on the physico-mechanical characteristics of HPC, the developed models present good correlation coefficients (R² = 0.82) for all studied responses. The obtained results indicated that it is quite possible to substitute a part of cement with LF and PF in the formulation of a HPC. Thanks to the complementary effect between the two additions, the workability could be improved and the strengths drop could be avoided in the short, medium and long term. The optimization of mixture design factors based on the mathematical models was carried out to select the appropriate factors combinations; a good agreement between the experimental results and the predicted results was obtained.

The coefficient of PF in Cs₂₈ model is closer to that of LF than in Cs₇ model, thanks to the complementary effect between LF and PF at the age of 28 days. It was found that the optimal HPC14 concrete (10%LF–5%PF) provides the best compromise between the three responses. It is also worth noting that the use of these two local materials can reduce the manufacturing costs of HPC and reduce carbon dioxide emissions into the atmosphere. This can be an important economic and environmental alternative.

In spite of the present importance of cobalt, relatively little information is available on the resistance of this metal to corrosion. Probably the main reason for the paucity of data on this subject is that, although the corrosion resistance at elevated temperatures of several cobalt‐base alloys is outstanding, cobalt is not utilised to any appreciable extent in its unalloyed condition, owing to the greater abundance and lower price of its sister metal nickel.