Search results

The purpose of this study is to demonstrate the potential of three-dimensional printing technology for the remanufacturing of end-of-life (EoL) composites. This technology will enable the rapid fabrication of environmentally sustainable structures with complex shapes and good mechanical properties. These three-dimensional printed objects will have several application fields, such as street furniture and urban renewal, thus promoting a circular economy model.

For this purpose, a low-cost liquid deposition modeling technology was used to extrude photo-curable and thermally curable composite inks, composed of an acrylate-based resin loaded with different amounts of mechanically recycled glass fiber reinforced composites (GFRCs). Rheological properties of the extruded inks and their printability window and the conversion of cured composites after an ultraviolet light (UV) assisted extrusion were investigated. In addition, tensile properties of composites remanufactured by this UV-assisted technology were studied.

A printability window was found for the three-dimensional printable GFRCs inks. The formulation of the composite printable inks was optimized to obtain high quality printed objects with a high content of recycled GFRCs. Tensile tests also showed promising mechanical properties for printed GFRCs obtained with this approach.

The novelty of this paper consists in the remanufacturing of GFRCs by the three-dimensional printing technology to promote the implementation of a circular economy. This study shows the feasibility of this approach, using mechanically recycled EoL GFRCs, composed of a thermoset polymer matrix, which cannot be melted as in case of thermoplastic-based composites. Objects with complex shapes were three-dimensional printed and presented here as a proof-of-concept.

This study aims to investigate rheological and extrusion behavior of thermosetting epoxy resins, which to find the universal property and printing parameters for extrusion-based rapid prototyping applications.

The thickener proportion greatly influences its viscosity and rheological behavior and therefore plays an important role in the shape of the cross-section of the extrudate.

A pseudoplastic (shear-thinning) is a basic requirement for obtaining extruded lines with plump cross-sections. In addition to the effects of the rheological behavior of the composite, shape maintenance and its wettability on the substrate, the cross-sectional geometry of the extrudate is also strongly affected by printing process parameters including the extrusion nozzle height, nozzle moving speed, extrusion rate and critical nozzle height. Proper combinations of these process parameters are necessary to obtain single-line extrudates with plump cross-sections and 3-D objects with dimensional accuracy, uniform wall thickness, good wall uprightness and no wall slumping. Formulas and procedures for determining these extrusion parameters are proposed and demonstrated in experiments.

The results obtained have been explained in terms of the interactions among the rheological properties of the composite, the shear rate imposed on the composite during extrusion, the wettability of the composite on the substrate and the shape maintenance of the composite during extrusion.

Three-dimensional printing of concrete (3DPC) has a potential for the rapid industrialization of the housing sector, with benefits of reduced construction time due to no formwork requirement, ease of construction of complex geometries, potential high construction quality and reduced waste. Required materials adaption for 3DPC is within reach, as concrete materials technology has reached the point where performance-based specification is possible by specialists. This paper aims to present an overview of the current status of 3DPC for construction, including existing printing methods and material properties required for robustness of 3DPC structures or structural elements.

This paper has presented an overview of three categories of 3DPC systems, namely, gantry, robotic and crane systems. Material compositions as well as fresh and hardened properties of mixes currently used for 3DPC have been elaborated.

This paper presents an overview of the state of the art of 3DPC systems and materials. Research needs, including reinforcement in the form of bars or fibres in the 3D printable cement-based materials, are also addressed.

The critical analysis of the 3D concrete printing system and materials described in this review paper is original.

The purpose of this paper is to provide insight into the way object data on Thingiverse changes over time, analyzing the relationships among views, downloads, likes, makes, remixes and comments over 500 days.

In total, 30 of the most popular things on Thingiverse were tracked between August 26, 2018 and January 7, 2020, with data collected about the different interactions at five intervals.

Highlights include: “#3DBenchy” became the first thing to reach one million downloads during this study. The “Xbox One controller mini wheel” achieved the highest documented download rate of 698 downloads per day. The average conversion rate from downloads to makes for all 30 things was one make for every 474 downloads at the start of the study, declining to one make for every 784 downloads by the conclusion.

With over 1.6 million things on Thingiverse, this study focused on an exclusive group of things that have gained significant attention from makers and does not represent most things on the platform.

Although often considered a novelty or niche maker community, this research shows that things on Thingiverse are achieving popularity comparable to digital music, video and imagery, and a large ecosystem of things has been growing that has implications for designers, manufacturers, supply chain managers and universal popular culture.

This is the first study to track the digital behaviors of 3D printable things over time, revealing new knowledge about how people interact with content and the scale of these interactions.

In pursuit of affordable and nutrient-rich food alternatives, the symbiotic culture of bacteria and yeast (SCOBY) emerged as a selected food ink for 3D printing. The purpose of this paper is to harness SCOBY’s potential to create cost-effective and nourishing food options using the innovative technique of 3D printing.

This work presents a comparative analysis of the printability of SCOBY with blends of wheat flour, with a focus on the optimization of process variables such as printing composition, nozzle height, nozzle diameter, printing speed, extrusion motor speed and extrusion rate. Extensive research was carried out to explore the diverse physical, mechanical and rheological properties of food ink.

Among the ratios tested, SCOBY, with SCOBY:wheat flour ratio at 1:0.33 exhibited the highest precision and layer definition when 3D printed at 50 and 60 mm/s printing speeds, 180 rpm motor speed and 0.8 mm nozzle with a 0.005 cm³/s extrusion rate, with minimum alteration in colour.

Food layered manufacturing (FLM) is a novel concept that uses a specialized printer to fabricate edible objects by layering edible materials, such as chocolate, confectionaries and pureed fruits and vegetables. FLM is a disruptive technology that enables the creation of personalized and texture-tailored foods, incorporating desired nutritional values and food quality, using a variety of ingredients and additions. This research highlights the potential of SCOBY as a viable material for 3D food printing applications.

The research-to-practice gap occurs when practices supported as effective by research are infrequently used in applied settings, such as classrooms. This gap may be due to teachers preferring to use practices they find to be trustworthy, usable, and accessible. Instead of relying on research, teachers frequently use resources from other teachers, which may be because teachers prefer practices that are supported by evidence developed in applied settings (i.e., practice-based evidence [PBE]). Using PBE to support the application of evidence-based practices (EBPs) may increase the latter's use in classrooms. In this chapter, we discuss the advantages and disadvantages of both EBPs and PBE and how the two can complement each other to help lessen the research-to-practice gap. We also discuss mixed-methods approaches that can be used to combine EBPs with PBE.

There has been increasing interest in the development of printable electronics to meet the growing demand for low‐cost, large‐area, miniaturized, flexible and lightweight devices. The purpose of this paper is to discuss the electronic applications of novel printable materials.

The paper addresses the utilization of polymer nanocomposites as it relates to printable and flexible technology for electronic packaging. Printable technology such as screen‐printing, ink‐jet printing, and microcontact printing provides a fully additive, non‐contacting deposition method that is suitable for flexible production.

A variety of printable nanomaterials for electronic packaging have been developed. This includes nanocapacitors and resistors as embedded passives, nanolaser materials, optical materials, etc. Materials can provide high‐capacitance densities, ranging from 5 to 25 nF/in², depending on composition, particle size, and film thickness. The electrical properties of capacitors fabricated from BaTiO₃‐epoxy nanocomposites showed a stable dielectric constant and low loss over a frequency range from 1 to 1,000 MHz. A variety of printable discrete resistors with different sheet resistances, ranging from ohm to Mohm, processed on large panels (19.5×24 inches) have been fabricated. Low‐resistivity materials, with volume resistivity in the range of 10⁻⁴‐10⁻⁶ ohm cm, depending on composition, particle size, and loading, can be used as conductive joints for high‐frequency and high‐density interconnect applications. Thermosetting polymers modified with ceramics or organics can produce low k and lower loss dielectrics. Reliability of the materials was ascertained by (Infrared; IR‐reflow), thermal cycling, pressure cooker test (PCT) and solder shock testing. The change in capacitance after 3× IR‐reflow and after 1,000 cycles of deep thermal cycling between −55°C and +125°C was within 5 per cent. Most of the materials in the test vehicle were stable after IR‐reflow, PCT, and solder shock.

The electronic applications of printable, high‐performance nanocomposite materials such as adhesives (both conductive and non‐conductive), interlayer dielectrics (low‐k, low‐loss dielectrics), embedded passives (capacitors and resistors), and circuits, etc.. are discussed. Also addressed are investigations of printable optically/magnetically active nanocomposite and polymeric materials for fabrication of devices such as inductors, embedded lasers, and optical interconnects.

A thin film printable technology was developed to manufacture large‐area microelectronics with embedded passives, Z‐interconnects and optical waveguides, etc. The overall approach lends itself to package miniaturization because multiple materials and devices can be printed in the same layer to increase functionality.

This study aims to discuss the effect of carbon nanotubes (CNTs) on the mechanical properties of acrylonitrile–butadiene–styrene (ABS) composites fabricated by additive manufacturing (AM). Insight into the energy-dissipation mechanisms introduced and/or enhanced by the addition of CNTs is presented in this study.

ABS/CNT filaments were fabricated with different concentrations of CNTs. Using a fused deposition modeling approach, unidirectional specimens were printed using a MakerBot Replicator 2X (MakerBot Industries, Brooklyn, NY, USA). Specimens were tested under static and dynamic conditions, with the loading coinciding with the printing direction, to determine elastic modulus, strength and viscoelastic properties.

A CNT reinforcing effect is evident in a 37 per cent increase in elastic modulus. Likewise, the strength of the composite increases by up to 30 per cent with an increase in weight fraction of CNTs. At low dynamic strain amplitudes (0.05 per cent), a correlation between dissipated strain energy of the butadiene phase and strength of the composite is found such that less dissipation, from constraint of the butadiene particles by the CNTs, leads to higher strength of the composite. At higher dynamic strains, the presence of a high concentration of CNT leads to increased energy dissipation, with a maximum measured value of 24 per cent higher loss factor compared to baseline specimens. Because the trend of the composite behavior is similar (with a higher absolute value) to that of neat ABS, this study’s results indicate that well-established polymer/CNT dissipation mechanisms (such as stick-slip) are not significant, but that the CNTs amplify the dissipation of the ABS matrix by formation of crazes through stress concentrations.

This study provides knowledge of the dissipation behavior in additively manufactured ABS/CNT composites and provides insight into the expansion to new printable materials for dynamics applications.

The class of models that can be represented by STL files is larger than the class of models that can be printed using additive manufacturing technologies. Stated differently, there exist well-formed STL files that cannot be printed. This paper aims to formalize such a gap and describe a fully automatic procedure to turn any such file into a printable model.

Based on well-established concepts from combinatorial topology, this paper provide an unambiguous description of all the mathematical entities involved in the modeling-printing pipeline. Specifically, this paper formally defines the conditions that an STL file must satisfy to be printable, and, based on these, an as-exact-as-possible repairing algorithm is designed.

It has been found that, to cope with all the possible triangle configurations, the algorithm must distinguish between triangles that bind solid parts and triangles that constitute zero-thickness sheets. Only the former set can be fixed without distortion.

Owing to the specific approach used that tracks the so-called “outer hull,” models with inner cavities cannot be treated.

Thanks to this new method, the shift from a 3D model to a printed prototype is faster, easier and more reliable.

The availability of this easily accessible model preparation tool has the potential to foster a wider diffusion of home-made 3D printing in non-professional communities.

Previous methods that are guaranteed to fix all the possible configurations provide only approximate solutions with an unnecessary distortion. Conversely, this procedure is as exact as possible, meaning that no visible distortion is introduced unless it is strictly imposed by limitations of the printing device. Thanks to such unprecedented flexibility and accuracy, this algorithm is expected to significantly simplify the modeling-printing process, in particular within the continuously emerging non-professional “maker” communities.