Search results

This paper aims to present a compact, broadband substrate integrated waveguide (SIW) three-way power divider with improved isolation based on six-port SIW coupler.

The power coupling among the three output ports occurs due to short openings in the narrow walls of the central SIW channel. Performance improvement in the isolation and return loss among ports is achieved using matching posts placed at the input and output ends of the coupling region. This enhances the coupling between TE₁₀ and TE₃₀ modes. The input matching ports enhance the return loss, whereas the isolation is alleviated by both the input and output matching posts. The bandwidth enhancement is achieved by optimizing the outer SIW channel widths.

The measured fractional bandwidth of 27.3% with over 15 dB of isolation and return loss is achieved. The coupling length is 1.55 λ_g at the centre frequency. The power divider achieves better than 15 dB isolation between non-adjacent output ports. The measured reflection and isolation coefficients are in close agreement with simulated results over 8.2 to 10.8 GHz.

Isolation between the adjacent and non-adjacent ports is an important parameter as the reflections from these ports will interfere with signals from other ports reducing the fractional bandwidth of the power divider and affecting the overall performance of the transmitters and receivers.

The authors present the enhancement of isolation between the output non-adjacent ports by optimizing the SIW channel width and matching post in the coupling region to reduce the reflected signals from non-adjacent ports entering into other ports. To the author’s knowledge, this is the only SIW three-way power divider paper showing non-adjacent port isolation among six-port couplers based three-way power dividers.

The purpose of this paper is to propose a new design strategy to enhance the bandwidth and efficiency of the power amplifier.

To realize the introduced design strategy, a power amplifier was designed using TSMC CMOS 0.18um technology for operating in the Ka-band, i.e. the frequency range of 26.5-40 GHz. To design the power amplifier, first, a power divider (PD) with a very wide bandwidth, i.e. 1-40 GHz, was designed to cover the whole Ka-band. The designed Doherty power amplifier consisted of two different amplification paths called main and auxiliary. To amplify the signal in each of the two pathways, a cascade distributed power amplifier was used. The main reason for combining the distributed structure and cascade structure was to increase the gain and linearity of the power amplifier.

Measurements results for designed power dividers are in good agreement with simulations results. The simulation results for the introduced structure of the power amplifier indicated that the gain of the proposed power amplifier at the frequency of 26-35 GHz was more than 30 dB. The diagram of return loss at the input and output of the power amplifier in the whole Ka-band was less than −8dB. The maximum power-added efficiency (PAE) of the designed power amplifier was 80%. The output P1dB of the introduced structure was 36 dB and the output power of the power amplifier was 36 dBm. Finally, the IP3 value of the power amplifier was about 17 dB.

The strategy presented in this paper is based on the usage of Doherty and distributed structures and a new wideband power divider to benefit from their advantages simultaneously.

The purpose of this paper is to present the result of research on a new fabrication technology of printed circuits board and electronics modules. The new method is based on inkjet printing technique on flexible substrates using new generations of heterophase inks. New fabrications method was used to print microwave waveguides and signal splitters as new technology demonstrators.

A fully Inkjet printed filter was printed on a flexible, transparent Kapton foil using heterophase inks developed in Instytut Technologii Materiałów Elektronicznych (ITME) for the purpose of this research based on graphene and silver nanoparticles.

A microwave module was printed using two types of Inkjet printers – PixDro LP50 with KonicaMinolta 512 printhead – and developed in an Instytut Tele- i Radiotechniczny (ITR) laboratory printer using MicroDrop a 100-μm glass nozzle printhead. Fully printed microwave circuits were evaluated by their print quality and electrical properties.

Fully Inkjet printed microwave circuits using the heterophase graphene ink were evaluated by their print quality and electrical properties.

The purpose of this paper is to introduce modified in–phase and quadrature components (I–Q) demodulator based on low temperature co-fired ceramics (LTCC) dielectric substrate GreenTape 951PX for M-Sequence ultra-wide band (UWB) sensor system.

Microstrip low pass (LP) and band pass (BP) filters for UWB sensor systems with required properties (for both filters, minimum attenuation is −40dB in stopband, bandwidth of pass band is 6 to 8.5 GHz for BP filter and cutoff frequency is 2.5 GHz for LP filter) were designed, simulated, fabricated and measured using dielectric substrates Du Pont GreenTape 951 PX. The developed microstrip filters were integrated with all parts of I–Q demodulator on one multilayer structure based on LTCC substrate Du Pont GreenTape 951 PX.

Both type of microstrip filters integrated in the I– Q demodulator achieved better transmission characteristics in comparison with commercial available filters. It was shown that LTCC technology based on GreenTape 951PX proves good stability in gigahertz frequency and suitability for fabrication of I–Q demodulator with a multilayer approach.

The novelty of this work lies in substituting commercially available LP and BP filters used in I– Q demodulator by microstrip LP and BP filters with better performance and furthermore the I– Q demodulator is fabricated based on LTCC instead of previously used PCB.

This purpose of this study is to present a novel four-element array antenna in combination with a modified Wilkinson power divider feeding network.

The two covering bands of this planar array antenna are achieved by an Elephant trunk shape (ETS) radiating element; therefore, two frequency bands for Bluetooth (2.4 GHz) and the wireless local area network (WLAN) band (5.15-5.825 GHz) are obtained.

An improved design of the power divider with curved corners rather than the sharp edges and certain new modifications in the length of matching stubs are implemented.

This paper describes an improved four-way Wilkinson power divider with excellent loss of insertion and adequate return loss for all ports and good isolation performance within two frequency bands (2.4 and 5.5 GHz) and when loaded with array components; the modified power divider complies with the design requirements. To comprehend its behavior, numerical and experimental results are provided. The simulated and measured results indicate a proper bandwidth coverage of the suggested antenna, stable radiation patterns and high gain.

The purpose of this paper is to build a neural network (NN) inverse model for the multi-band unequal-power Wilkinson power divider (WPD). Because closed-form expressions of the inverse input–output relationship do not exist, the NN becomes an appropriate choice, because it can be trained to learn from the data in inverse modeling. The design parameters of WPD are the characteristic impedances, lengths of the transmission line sections and the isolation resistors. The design equations used to train the NN inverse model are based on the even–odd mode analysis.

An inverse model of a multi-band unequal WPD using NNs is presented. In inverse modeling of a microwave component, the inputs to the model are the required electrical parameters such as reflection coefficients, and the outputs of the model are the geometrical or the physical parameters.

For verification purposes, a quad-band WPD and a penta-band WPD are designed. The results of the full-wave simulations verify the validity of the design procedure. The resulting NN model outperforms traditional time-consuming optimization procedures in terms of computation time with acceptable accuracy. The designed WPDs using NN are implemented by microstrip lines and verified by using full-wave analysis based on high-frequency structure simulator (HFSS). The results of the microstrip WPDs have good agreements with the corresponding results obtained by using ideal transmission line sections.

The associated time-consuming procedure and computational burden in realizing WPD through optimization are major disadvantages; needless to mention the substantial increase in optimization time because of the multi-band design. NNs are one of the best candidates in addressing the abovementioned challenges, owing to their ability to process the interrelation between electrical and geometrical/physical characteristics of the WPD in a superfast manner.

Performance characteristics of a two‐way impedance transforming Wilkinson divider are computed using design parameters obtained by imposing the conditions of perfect match at the input port and infinity isolation at the output ports at the center frequency of operation. It is found that, theoretically, infinity bandwidth of match at the input port and split is achieved for an impedance transformation of 2:1 and that similar input VSWR and insertion loss characteristics are achieved for two cases with transformation ratios (R2/R1) whose product is 4:1.

This paper aims to present the design, fabrication and analysis of a wideband, enhanced gain 1 × 2 patch antenna array with a simple profile structure to meet the desired antenna traits, such as wide bandwidth, high gain and directional patterns expected for the upcoming fifth-generation (5G) wireless applications in the millimeter wave band. To enhance these parameters (bandwidth and gain), a new antenna geometry by using a T-junction power divider is presented.

The theory behind this paper is connected with advancements in the 5G communications related to antennas. The methodology used in this work is to design a high gain array antenna and to identify the best possible power divider to deliver the power in an optimized way. The design methodology adopts several steps like the selection of proper substrate material as per the design specification, size of the antenna as per the frequency of operation and application-specific environment condition. The simulation has been performed on the designed antenna in the electromagnetic simulation tool (high-frequency structure simulator [HFSS]), and optimization has been done with parametric analysis, and then the final array antenna model is proposed. The proposed array contains 2-patch elements excited by one port adapted to 50 Ω through a T-junction power divider. The 1 × 2 array configuration with the suggested geometry helps to improve the overall gain of the antenna, and the implementation of the T-junction power divider provides enhanced bandwidth. The proposed array designed using a 1.6 mm thick flame retardant substrate occupies a compact area of 14 × 12.14 mm².

The prototype of the array antenna is fabricated and measured to validate the design concept. A good agreement has been reached between the measured and simulated antenna parameters. The measured results confirm its wideband and high gain characteristics, covering 24.77–28.80 GHz for S₁₁= –10 dB with a peak gain of about 15.16 dB at 27.65 GHz.

The proposed antenna covers the bandwidth requirements of the 26 GHz n258 band (24.25–27.50 GHz) to be deployed in the UK and Europe. The suggested antenna structure also covers the federal communications commission (FCC)-regulated 28 GHz n261 band (27.5–28.35 GHz) to be deployed in America and Canada. The low profile, compact size, simple structure, wide bandwidth, high gain and desired directional radiation patterns confirm the applicability of the suggested array antenna for the upcoming 5 G wireless systems.

The overall performance of an electronic nose system will depend on the individual performance of its constituent elements. Although often overlooked, it is clear that careful design/selection of the front‐end signal conditioning circuit is of critical importance if optimal performance of the odour sensing system is to be achieved. In this paper circuits are reviewed, which have been employed as front‐end signal conditioners for resistance‐based sensors in electronic nose systems, with many of the conclusions drawn being equally applicable to other resistor sensors. The relevant equations governing the behaviour of each circuit methodology are derived and advantages and disadvantages are discussed. The performance of the circuit is then quantitatively assessed in a specific test case, in which the maximum sensitivity of the circuit is calculated in relation to the task of interfacing to a theoretical thin‐film conducting‐polymer sensor.

An Elephant trunk shape (ETS) radiating element is used to achieve the two covering bands of multi-input multi-output (MIMO) antenna. These frequency bands can be controlled by the length of a slot embedded in ETS. The slot length in ETS plays a defining role in controlling the impedance bandwidth (IBW) of the MIMO antenna, and its diligent adjustment of it leads to cover the frequency range of Bluetooth and Wireless Local Area Network systems.

A new MIMO antenna is introduced in this paper in conjunction with an enhanced Wilkinson power divider feeding platform.

These frequency bands can be controlled by the length of a slot embedded in ETS. The slot length in ETS plays a defining role in controlling the IBW of the MIMO antenna, and its diligent adjustment leads to covering the frequency range of Bluetooth and WLAN systems.

The proposed MIMO antenna benefits from good isolation between ports for both frequency bands. The proposed MIMO antenna is constructed on FR4 substrate with a volume of 90 × 134 × 1.6 mm3.