Search results

This paper aims to develop efficient and simple models for thermal distribution, melt pool dimensions and controlled phase change in the laser additive manufacturing (AM) of bulk and powder particles ceramic materials.

This paper proposes new analytical models for the AM of bulk and powder bed ceramic materials. A volumetric moving heat source, along with the complete melting of bulk and powder particle materials, is taken into account. Different values of laser absorption coefficient in solid and liquid states have been used to investigate the phase transformation. Furthermore, the pores and voids dimensions are also included in the modeling. Theoretical predictions have been compared with the experimental analyses and finite element simulations in laser to silicon nitride and laser to alumina interaction. The analysis focuses on the impact of laser power and scanning speed on the melt pool width and depth evolution into the bulk substrate and powder bed.

This study shows that the powder particles exhibit a higher thermal distribution value than the bulk substrate because of voids in the powder layer. The laser beam experiences multiple reflections in the presence of porosity/voids, thus increasing the surface absorption coefficient, which becomes relevant with the increment in the pore/void dimension. A direct relationship has been found between the laser power and melt pool dimensions, while the scanning speed displayed an inverse relationship for the melt pool width and length. Larger melt dimensions were inferred in the case of laser–powder particle interaction compared with laser–bulk substrate interaction. A close correlation was found between the analytical simulations, experimental investigations and numerical simulation results within the range of 4%–8%.

This paper fulfills an identified need to develop efficient and simplified models for ceramics laser AM by taking into account different laser absorption coefficients in solid and liquid form, voids and pores dimensions and controlled phase transformation to avoid vapors and plasma formation. The limitation of the finite element simulation model is that the solution is strongly dependent on the mesh quality and accuracy directly linked to the computation efficiency and time. A finer mesh requires a longer computing time than a coarse mesh. Finite element simulations require, however, specialized skills.

This paper aims to provide a review on the process of additive manufacturing of ceramic materials, focusing on partial and full melting of ceramic powder by a high-energy laser beam without the use of binders.

Selective laser sintering or melting (SLS/SLM) techniques are first introduced, followed by analysis of results from silica (SiO₂), zirconia (ZrO₂) and ceramic-reinforced metal matrix composites processed by direct laser sintering and melting.

At the current state of technology, it is still a challenge to fabricate dense ceramic components directly using SLS/SLM. Critical challenges encountered during direct laser melting of ceramic will be discussed, including deposition of ceramic powder layer, interaction between laser and powder particles, dynamic melting and consolidation mechanism of the process and the presence of residual stresses in ceramics processed via SLS/SLM.

Despite the challenges, SLS/SLM still has the potential in fabrication of ceramics. Additional research is needed to understand and establish the optimal interaction between the laser beam and ceramic powder bed for full density part fabrication. Looking into the future, other melting-based techniques for ceramic and composites are presented, along with their potential applications.

The consolidation process and morphology evolution in ceramics-based additive manufacturing (AM) are still not well-understood. As a way to better understand the ceramic selective laser sintering (SLS), a dynamic three-dimensional computational model was developed to forecast thermal behavior of hydroxyapatite (HA) bioceramic.

AM has revolutionized automotive, biomedical and aerospace industries, among many others. AM provides design and geometric freedom, rapid product customization and manufacturing flexibility through its layer-by-layer technique. However, a very limited number of materials are printable because of rapid melting and solidification hysteresis. Melting-solidification dynamics in powder bed fusion are usually correlated with welding, often ignoring the intrinsic properties of the laser irradiation; unsurprisingly, the printable materials are mostly the well-known weldable materials.

The consolidation mechanism of HA was identified during its processing in a ceramic SLS device, then the effect of the laser energy density was studied to see how it affects the processing window. Premature sintering and sintering regimes were revealed and elaborated in detail. The full consolidation beyond sintering was also revealed along with its interaction to baseplate.

These findings provide important insight into the consolidation mechanism of HA ceramics, which will be the cornerstone for extending the range of materials in laser powder bed fusion of ceramics.

This paper gives a bibliographical review of the finite element methods (FEMs) applied to the analysis of ceramics and glass materials. The bibliography at the end of the paper contains references to papers, conference proceedings and theses/dissertations on the subject that were published between 1977‐1998. The following topics are included: ceramics – material and mechanical properties in general, ceramic coatings and joining problems, ceramic composites, ferrites, piezoceramics, ceramic tools and machining, material processing simulations, fracture mechanics and damage, applications of ceramic/composites in engineering; glass – material and mechanical properties in general, glass fiber composites, material processing simulations, fracture mechanics and damage, and applications of glasses in engineering.

The purpose of this paper is to assess a new powder metallurgy process to make alumina parts through indirect selective laser sintering (SLS). Density measurements, some geometrical assessments and scanning electron microscopy (SEM) microstructural analyses are performed after each stage of the process, allowing an objective overview to be provided of the challenges and possibilities for the processing of high density technical ceramic parts through SLS of ball milled alumina/polyamide powder agglomerates.

The powder production by ball milling, SLS, cold isostatic pressing (CIP) or quasi isostatic pressing (QIP), debinding and sintering (FS) stages of the powder metallurgy process were sequentially investigated.

Alumina parts with a density up to 94.1 per cent could be produced by a powder metallurgy process containing an SLS step. Microstructural investigation of the sintered samples reveals an alumina matrix with a grain size of ∼5 μm and two different kinds of pore morphologies, i.e. long elongated pores, which stem from the intergranular spacings during SLS, and intermediate pores, which likely originate from larger polyamide agglomerates in the ball milled powder. Also, QIPing at elevated temperatures is found to be a promising alternative for CIPing at room temperature to increase the final part density.

Cracks, long elongated pores and intermediate pores remained in the sintered parts. Homogenizing the microstructure of the parts through optimizing the composite starting powder, the deposition during SLS, the SLS parameters and QIPing parameters is essential to overcome these limitations.

Homogenizing the starting powder mixture and the microstructure of the SLS material is the key issue for producing ceramic parts through indirect SLS.

Indirect SLS of ceramics has hardly been reported and the combined use of SLS and QIPing is innovative in the field of indirect SLS of ceramics.

The purpose of this paper is to report a study about the rapid prototyping method of dental glass‐ceramic restoration.

Dental glass‐ceramic restoration materials have excellent physical and chemical, mechanical, aesthetic and biocompatibility characteristics. However, casting methods adopted at present have complicated procedures and high costs; the forming qualities are especially difficult to control. These problems greatly restrict their clinical application and promotion. Therefore, a new forming process based on selective laser sintering (SLS) technology is proposed. First, dental glass‐ceramic is processed into fine powder through a special heat treatment process. Then, the dental restoration parts are manufactured using SLS without any moulds. In this paper, the effects of processing parameters including laser power, scan speed, scan spacing and preheating temperature on the relative density and mechanical properties of the sintered parts are studied.

The experimental results have shown that for the composite powder of epoxy resin binder E‐12 and K₂O‐Al₂O₃‐SiO₂ series of dental glass‐ceramics, when preheating temperature, layer thickness, laser power, scan speed and scan spacing are, respectively, 30∼35°C, 0.08 mm, 21 W, 1,800 mm/s and 0.10 mm/s, the relative densities of dental glass‐ceramic parts are relatively high; the mechanical properties and forming effect are excellent. The relative density and bending strength of SLS parts under the optimized processing parameters are 37.40 per cent and 2.08 MPa, respectively.

This study only concerns the preparation and SLS of the dental glass‐ceramic powders. Further investigations are planned to be conducted on post processing, such as binder decomposition, isostatic press and high temperature sintering.

This study will provide a theoretical and technical basis for dental glass‐ceramic restorations of SLS.

This paper aims to reduce part defects and improve ceramic additive manufacturing (AM). Selective laser melting (SLM) experiments were carried out to explore the effect of laser power and scanning speed on the microstructure, melting behaviour and surface roughness of cuprous oxide (Cu₂O) ceramic.

The experiments were designed based on varying laser power and scanning speed. The laser power was changed between 50 W and 140 W, and the scanning speed was changed between 170 mm/s and 210 mm/s. Other parameters, such as scanning strategy, layer thickness and hatch spacing, remain constant.

Laser power and scan speed are the two important laser parameters of great significance in the SLM technique that directly affect the molten state of ceramic powders. The findings reveal that Cu₂O part defects are widely controlled by gradually increasing the laser power to 110 W and reducing the scanning speed to 170 mm/s. Furthermore, excessive laser power (>120 W) caused surface roughness, cavities and porous microstructure due to the extremely high energy input of the laser beam.

The SLM technique was used to produce Cu₂O ceramic specimens. SLM of oxide ceramic became feasible using a slurry-based approach. The causes of several part defects such as spattering effect, crack initiation and propagation, the formation of porous microstructure, surface roughness and asymmetrical grain growth during the SLM of cuprous oxide (Cu₂O) are thoroughly investigated.

The purpose of this work is to introduce a novel approach of using additive manufacturing (AM) to produce dense complex ceramic and metallic parts. Powder 3D printing has been gaining popularity due to its ease of use and versatility. However, powder-based methods such as Selective Laser Melting (SLM) and Sintering (SLS), utilizes high power lasers which generate thermal shock conditions in metals and are not ideal for ceramics due to their high melting temperature. Indirect additive manufacturing methods have been explored to address the above issues but have proven to be wasteful and time-consuming.

In this work, a novel approach of producing high density net-shaped prototypes using subtractive sintering (SS) and solvent jetting is developed. AM combined with SS (AM-SS) is a process that includes five simple steps. AM-SS can produce repeatable and reliable results as has been shown in this work.

As a proof-of-concept, a zirconia dental crown with a high density of 97% is fabricated using this approach. Microstructure and properties of the fabricated components are analyzed.

A major advantage of this method is the ability to efficiently fabricate high density parts using either metal powder and more importantly, ceramic powder which is traditionally difficult to densify using AM. Additionally, any powder particle size (including nano) and shape can be used which is not the case for traditional powder-based 3D printing.

This paper aims to consolidate the results of various researchers focusing the different applications, so that this paper could become the torch bearer for the futuristic researchers working in the domain of cold gas dynamics spray coating.

A study on the cold spray coating is presented by summarizing the data present in literature. Important factors such as coating temperature, pressure, coating thickness, particle size, which affect the erosion-corrosion (E-C) resistance, physical and mechanical properties of boiler steel are stated. This paper also addresses the use of cold spray coating and compares it with other different thermal spray processes.

From the literature review, it was noticed that cold spray technology is best as compare to other thermal spray processes to reduce porosity, increase hardness, adhesion strength and retention in properties of feedstock powders.

Cold spray coating technology has a great potential in almost every field especially in restoration of surfaces, generation of complex surface, biomedical application, resist hot corrosion, wear, oxidation and erosion corrosion.

Selective laser sintering (SLS) is one of the most rapidly growing rapid prototyping techniques (RPT). This is mainly due to its suitability to process almost any material: polymers, metals, ceramics (including foundry sand) and many types of composites. The material should be supplied as powder that may occasionally contain a sacrificial polymer binder that has to be removed (debinded) afterwards. The interaction between the laser beam and the powder material used in SLS is one of the dominant phenomena that defines the feasibility and quality of any SLS process. This paper surveys the current state of SLS in terms of materials and lasers. It describes investigations carried out experimentally and by numerical simulation in order to get insight into laser‐material interaction and to control this interaction properly.