Search results

This paper aims to present a novel position sensorless control scheme with fault-tolerance ability for switched reluctance motor at low speed.

First, the detection pulses are injected in the freewheeling and idle intervals of each phase. Second, the aligned position of each phase can be detected by comparing the consecutive rise time of detection current. Third, the whole-region rotor position and real-time rotational speed can be updated four times for the improvement of detection accuracy. Finally, the fault-tolerant control strategy is performed to enhance the robustness and reliability of proposed sensorless scheme under faulty conditions.

Based on proposed sensorless control strategy, the estimated rotor position is in good agreement with the actual rotor position and the maximum rotor position error is 1.5°. Meanwhile, the proposed sensorless scheme is still effective when the motor with multiphase loss and the maximum rotor position error is 1.9°. Moreover, the accuracy of the rotor position estimation can be ensured even if the motor is in an accelerated state or decelerated state.

The proposed sensorless method does not require extensive memory, complicated computation and prior knowledge of the electromagnetic properties of the motor, which is easy to implement. Furthermore, it is suitable for different control strategies at low speed without negative torque generation.

The aim of this paper is to present a new sensorless control strategy using a flux observer, which is particularly designed for taking into account the rotor saliency and winding inductance variation in an interior permanent magnet synchronous motor (IPMSM).

In a PMSM, the magnets‐excited flux‐linkage, i.e. the rotor flux‐linkage, can be expressed as a vector. Its phase angle stands for the rotor position. Therefore, if this vector is estimated with an observer, the rotor position can be obtained without a position sensor, consequently, sensorless control can be realized. The main object of this paper is to establish and implement a model of rotor flux observer, specifically for IPMSM.

The flux observer model is built on the d‐q‐0 frame, using unequal values of the d‐axis inductance L_d and q‐axis inductance L_q to represent the IPMSM rotor saliency. Its digital implementation is proposed, whilst the sensorless control strategy is experimentally verified.

Insignificant error exists in the estimated rotor position, probably due to the non‐sinusoidal variation of winding inductance. Further improvement of the observer model is preferable.

In previous works, the rotor flux observer is only applied to surface‐mounted permanent magnet synchronous motors (SPMSM) in which the winding inductance is constant. However, the proposed observer can deal with the rotor saliency and inductance variation in IPMSM, whilst its digital implementation is also new.

The purpose of this study is to improve the control performance of wind energy conversion systems (WECSs) by proposing a new sensorless, robust control strategy based on a Smith predictor active disturbance rejection control (SP-ADRC) associated with a speed/position estimator.

The estimator consists of a sliding mode observer (SMO) in combination with a phase-locked loop (PLL) to estimate the permanent magnet synchronous generator (PMSG) rotor position and speed. At the same time, the SP-ADRC is applied to the speed control loop of the variable-speed WECS control system to adapt strongly to dynamic characteristics under parameter uncertainties and disturbances.

Numerical simulations are conducted to evaluate the speed tracking performances under various wind speed profiles. The results show that the proposed sensorless speed control improves the accuracy of rotor speed and position estimation and provides better power tracking performance than a regular ADRC controller under fast wind speed variations.

This paper offers a new approach for designing sensorless, robust control for PMSG-based WECSs.

A new sensorless, robust control is proposed to improve the stability and tracking performance of PMSG-based WECSs. The SP-ADRC control attenuates the effects of parameter uncertainties and disturbances and eliminates the time-delay impact. The sensorless control design based on SMO and PLL improves the accuracy of rotor speed estimation and reduces the chattering problem of traditional SMO. The obtained results support the theoretical findings.

The purpose of this paper is to describe an effective method to eliminate or substantially reduce the modulation harmonics due to saturation and inter‐modulation for sensorless speed control induction motor drives at low and zero speed with high loads using artificial neural networks (ANNs).

In this paper, the separation of the saturation signal, the slotting signal, and the inter‐modulation signal components in squirrel cage induction machines operating at low and zero frequency using ANNs has been experimentally implemented and measurement results are given.

The measurement results show the advantages of the application of the proposed technique at low and zero speed sensorless control even at high load levels.

The paper describes an effective method of eliminating or reducing modulation harmonics in induction motor drives.

To purpose of this paper is to introduce a procedure to compute the d‐ and q‐axis parameters of the induction motor.

A finite element procedure, based on the d‐ and q‐axis model of the induction motor is adopted.

Such a procedure is well suited to analyse IM with anisotropic rotor, where an intentionally created saliency is introduced in the rotor bar geometry, so as to detect the IM rotor position without sensor.

The proposed procedure allows one to evaluate the sensorless control capability of the IM. It will be useful for both analysis of the IM performance and design of the machine itself.

For vector control of permanent magnet synchronous motor (PMSM) requires motor speed and rotor position estimation. The precision of the open-loop techniques of the stator flux and speed for vector control PMSM drive drops as mechanical speed decreases. The stator resistance and estimated stator flux values crisscross have a huge effect on the transient and steady-state performance of the drive at lower speed. The framework turns out to be increasingly strong against parameter crisscross and signal noises by using adaptive observers for estimation of speed and flux.

This paper presents a comparison of two-speed observers for the vector control PMSM drive: the sliding mode observer (SMO) and the model reference adaptive system (MRAS). A comprehensive analysis of SMO and MRAS respects dynamic, steady-state performance and robustness, affectability, stability and computational complexity has been introduced. The abstract of the advantages and disadvantages of both observer and their comparative analysis have also been discussed.

Dynamic performance steady-state performance and robustness, affectability and stability.

This paper presents a sensorless scheme, namely, MRAS and SMO for control of PMSM drive. These sensorless techniques have been tested for a PMSM motor drive and the motor performance was compared for both techniques. Matlab/Simulink based simulation results conclude that the adaptive methods improve dynamic response, reduces torque ripples and extended speed range.

To meet the need of reducing the cost of industrial systems, sensorless control applications on electrical machines are increasing day by day. This paper aims to improve the performance of the sensorless induction motor control system. To do this, the speed observer is designed based on the combination of the sliding mode and the fractional order integral.

Super-twisting sliding mode (STSM) and Grünwald–Letnikov approach are used on the proposed observer. The stability of the proposed observer is verified by using Lyapunov method. Then, the observer coefficients are optimized for minimizing the steady-state error and chattering amplitude. The optimum coefficients (c₁, c₂, k_i and λ) are obtained by using response surface method. To verify the effectiveness of proposed observer, a large number of experiments are performed for different operation conditions, such as different speeds (500, 1,000 and 1,500 rpm) and loads (100 and 50 per cent loads). Parameter uncertainties (rotor inertia J and friction factor F) are tested to prove the robustness of the proposed method. All these operation conditions are applied for both proportional integral (PI) and fractional order STSM (FOSTSM) observers and their performances are compared.

The observer model is tested with optimum coefficients to validate the proposed observer effectiveness. At the beginning, the motor is started without load. When it reaches reference speed, the motor is loaded. Estimated speed and actual speed trends are compared. The results are presented in tables and figures. As a result, the FOSTSM observer has less steady-state error than the PI observer for all operation conditions. However, chattering amplitudes are lower in some operation conditions. In addition, the proposed observer shows more robustness against the parameter changes than the PI observer.

The proposed FOSTSM observer can be applied easily for industrial variable speed drive systems which are using induction motor to improve the performance and stability.

The robustness of the STSM and the memory-intensive structure of the fractional order integral are combined to form a robust and flexible observer. This paper grants the lower steady-state error and chattering amplitude for sensorless speed control of the induction motor in different speed and load operation conditions. In addition, the proposed observer shows high robustness against the parameter uncertainties.

Sensorless online measurements, application of variable speed drives has been given a great attention, especially over the past few years. In most of the previous literates dealing with permanent magnet synchronous motor (PMSM) drives, the combination of inter-sampled behavior with high gain design approach has not been discussed yet. This paper aims to discuss this feature in-depth.

The study contains a different approach for an observer running with surface-mounted permanent magnet synchronous machine drives to implement sensorless control. Design of sampled data observer methodology for one kind of AC machine having non-linear model and backed by an elegant formal stability convergence analysis using the tools of Lyapunov stability techniques was highly recommended in scientific contributions, and it is yet needed to be solved.

In this study, a solution to observation problem is covered and developed by combining ideas from the high-gain design approach and inter-sample predictor based on stator voltage measurements. The output state currents are accessible only at the sampling instant to solve the problem of states observation at continuous-time mode. This allows to reducing the usage of online appliances, improving reliability of control design and saving costs.

The proposed observer is capable of guaranteeing an acceptable closed loop dynamic response over a wide range of operation region and industrial process for random initial conditions.

The output state predictor has been interred in constructing the innovation correct term to prove the robustness of the proposed observer against attenuated sampling interval. To validate the theoretical results introduced by the main fundamental theorem and prove the observer stability convergence, the proposed observer is demonstrated through a sample study application to variable speed permanent magnet synchronous machine drive.

Doubly fed induction generator (DFIG) is widely used in wind energy conversion systems and it can operate with other primary movers. The purpose of this paper is to focus on the standalone operation of DFIG which may expand the area of possible applications and increase capabilities of the generation system in terms of power quality.

Synthesis of the control method was preceded by analysis of mathematical model of the machine. The control method based on the negative sequence and high harmonics extraction has been developed and verified in the laboratory unit. Control of the fundamental frequency component uses neither rotor speed nor position sensors.

The original method allows to compensate negative sequence and high harmonics of the generated voltage. At the same time, due to the active filtering capability of the grid side converter, the stator phase current shape is close to sine wave. Thus, it is seen by the machine as a linear load, what eliminates the electromagnetic torque ripples.

The system and control method can be applied in variable speed generation systems, e.g. wind turbines or diesel engines operating in the standalone mode.

Although the selective compensation of negative sequence and harmonics are known in the literature, until now the methods have been verified for the system with a rotor position sensor. Moreover, the stator current feed-forward improving the transient properties, as well as results of transient states caused by the load step change, have not been proposed in publications.

The paper is concerned about parameter adaptation of a novel, simplified and nonlinear switched reluctance motor (SRM) model. The purpose of the presented on-line procedure is to give an opportunity to set the model parameters’ values to obtain a relatively good convergence with the real control object. This is important when a reference model is used for control (e.g. optimal) or object state classification (e.g. fault detection) purposes. The more convergent the real object model is, the better operation quality may be expected.

In the paper, a 12/8 pole’s SRM as a control object is analyzed. The model equations were verified experimentally by comparing phase current model estimations with reference (measured) ones at different operational points. Differential equations of motor winding currents were chosen as an approximation function in the fitting (parameter adaptation) process using the Newton and Gauss–Newton methods. The structure of the adaptation system is presented along with the implementation in simulation environment.

It was confirmed in the simulation tests that Newton and Gauss–Newton methods of nonlinear model parameters’ adaptation may be used for the SRM. The introduced fitting structure is well suited for implementation in real-time, embedded systems. The proposed approximation function could be used in process as an expansion to Jacobian and Hessian matrices. The χ² (chi²) coefficient (commonly used to measure the quality of the signal fitting) reduced to a low value during the adaptation process. Another introduced quality coefficient shows that the Newton method is slightly better in scope of the entire adaptation process time; however, it needs more computational power.

The proposed structure and approximation function formula in the parameters’ adaptation system is appropriate for sinusoidal distribution of the motor phase inductance value along the rotor angle position. The inductance angular shape is an implication of the mechanical construction – with appropriate dimensions and materials used. In the presented case, the referenced model is a three-phase SRM in 12/8 poles configuration used as a main drive part of Maytag Neptune washing machine produced by Emerson Motors.

The presented method of parameter adaptation for novel, simplified and nonlinear SRM model provides an opportunity for its use in embedded, real-time control systems. The convergent motor model, after the fitting procedure (when the estimations are close to the measurements from real object), may be used for solving many well-known control challenges such as detection of initial rotor position, sensorless control, optimal control, fault-tolerant control end in fault detection (FD) systems. The reference model may be used in FD in the way of deducing signals from the difference between the estimated and measured ones.

The paper proposed a new system of parameter adaptation for the evaluated nonlinear, simplified 12/8 poles SRM model. The relative simplicity of the proposed model equations provides the possibility of implementing an adaptation system in an embedded system that works in a real-time regime. A Two adaptation methods – Newton and Gauss–Newton – have been compared. The obtained results shown that the Newton fitting method is better in the way of the used quality indicator, but it consumes more computational power.