Search results

The purpose of this paper is to present the influence of plastic pyrolysis oil blended with gasoline at 10 per cent with and without ethanol additive at 5 per cent in a three-cylinder petrol engine.

The engine is running at standard working processes. The result of 10PPO is compared with pure petrol and additive-added blend. The outcomes clears that, the engine performance is reduced by using plastic oil blended with petrol and NO_x emission rates are increasing substantially.

To control the emission rate, ethanol is added, and corresponding performance reveals that brake thermal efficiency is 4.52 per cent increase compared to pure petrol and 7.03 per cent increase compared to without additive blend.

Emissions such as CO and NOx are considerably controlled with additive blend.

The purpose of this paper was to investigate the lubricity of palm biodiesel (PB)–diesel fuel with plastic pyrolysis oil (PPO) and waste cooking biodiesel (WCB).

Three quaternary fuels were prepared by mechanical stirring. B10 (10% PB in diesel) fuel was blended with 5%, 10% and 15% of both PPO and WCB. The results were compared to B30 (30% PB in diesel) and B10. The lubricity of fuel samples was determined using high-frequency reciprocating rig in accordance with ASTM D6079. The tribological behavior of all fuels was assessed by using scanning electron microscopy on worn steel plates to determine wear scar diameter (WSD) and surface morphology. The reported WSD is the average of the major and minor axis of the wear scar.

The addition of PPO and WCB to B10 had improved its lubricity while lowering wear and friction coefficients. Among the quaternary fuels, B40 showed the greatest reduction in coefficient of friction and WSD, with 7.63% and 44.5%, respectively, when compared to B10. When compared to B30a, the quaternary fuel mixes (B40, B30b and B20) exhibited significant reduction in WSD by 49.66%, 42.84% and 40.24%, respectively. Among the quaternary fuels, B40 exhibited the best overall lubricating performance, which was supported by surface morphology analysis. The evaluation of B40 indicated a reduced adhesive wear and tribo-oxidation, as well as a smoother metal surface, as compared to B20 and B30b.

Incorporation of PPO and WCB in PB–diesel blend as a quaternary fuel blend in diesel engines has not been reported. Only a few researchers looked into the impact of PPO and WCB on the lubricity of the fuel.

The purpose of this study is to predict the performance and emission characteristics of micro gas turbine engines powered by alternate fuels. The micro gas turbine engine performance, combustion and emission characteristics are analyzed for the jet fuel with different additives.

The experimental investigation was carried out with Jet A-1 fuel on the gas turbine engines at different load conditions. The primary blends of the Jet A-1 fuels are from canola and solid waste pyrolysis oil. Then the ultrasonication of highly concentrated multiwall carbon nanotubes is carried with the primary blends of canola (Jet-A fuel 70%, canola 20% and 10% ethanol) and P20E (Jet-A 70% fuel, 20% PO and 10% ethanol).

The consumption of the fuel is appreciable with the blends at a very high static thrust. The 39% reduction in thrust specific fuel consumption associated with a 32% enhance in static thrust with P20E blend among different fuel blends. Moreover, due to the increase in ethanol concentration in the blends PO20E and C20E lead to a 22% rise in thermal efficiency and a 9% increase in higher oxygen content is observed.

The gas turbine engine emits very low emission of gases such as CO, CO₂ and NOx by using the fuel blends, which typically reduces the fossil fuel usage limits with reduced pollutants.

The emission of the gas turbine engines is further optimized with the addition of hydrogen in Jet-A fuel. That is leading to high specific fuel exergy and owing to the lower carbon content in the hydrogen fuel when compared with that of the fossil fuels used in gas turbine engines. Therefore, the usage of hydrogen with nanofluids was so promising based on the results obtained for replacing fossil fuels.

This paper aims to present the production of waste plastic oil from landfill waste plastics, the performance and emissions of a compression ignition (CI) engine, using waste plastic oil, were tested and compared with using diesel oil. The physical characteristics, gross calorific value (MJ/kg), kinematic viscosity cst @40°C, specific gravity @15.6°C, cetane index, flash point and distillation temperature @90 per cent are determined. The experimental CI engine is a four-stroke, direct injection, single cylinder, 709 C.C. and has been tested with in-brake-specific fuel consumption (BSFC), brake conversion efficiency, brake-specific energy consumption and exhaust gas emissions.

The results show that the characteristics of liquid fuel from landfill plastics (LFLP3) are similar to diesel oil. The CI engine was able to run with LFLP3. The efficiency was slightly higher than that of diesel fuel, whereas the BSFC was lower. The exhaust-gas emission average for LFLP3 was reduced compared to diesel oil operation.

The efficiency of the CI engine using LFLP3 is slightly higher than diesel fuel at all load conditions. In this study, LFLP3 was a lower pollutant than diesel fuel. Environmental values and energy consumption are important when reviewing the ignition of any fuel in a combustion chamber.

The efficiency of the CI engine using LFLP3 is slightly higher than diesel fuel at all load conditions. In this study, LFLP3 was a lower pollutant than diesel fuel. Environmental values and energy consumption are important when reviewing the ignition of any fuel in a combustion chamber.

Purpose – This work aims to study the treatment of adsorbant on the increasing liquid hydrocarbon quality produced by pyrolysis low density polyethylene (LDPE) plastic waste at low temperature. The hydrocarbon distribution, physicochemical properties and emission test were also studied due to its application in internal combustion engine. This research uses pure Calcium carbonate (CaCO₃) and pure activated carbon as adsorbant, LDPE type clear plastic samples with control variable that is solar gas station.

Design/Methodology/Approach – LDPE plastic waste of 10 kg were vaporized in the thermal cracking batch reactor using LPG 12 kg as fuel at range temperature from 100 to 300°C and condensed into liquid hydrocarbon. Furthermore, this product was treated with the mixed CaCO₃ and activated carbon as adsorbants to decrease contaminant material.

Findings – GC-MS identified the presence of carbon chain in the range of C6–C44 with 24.24% of hydrocarbon compounds in the liquid. They are similar to diesel (C6–C14). The 30% of liquid yields were found at operating temperature of 300°C. The calorific value of liquid was 46.021 MJ/Kg. This value was 5.07% higher than diesel as control.

Originality/Value – Hydrocarbon compounds in liquid produced by thermal cracking at a low temperature was similar to liquid from a catalytic process.

The authors aim to investigate the use of pyrolysis for the processing of waste printed circuit boards (PCBs). The aim was to make the process of separating the organic, metallic, and glass fibre fractions of PCBs much easier and therefore make recycling of each PCB fraction more viable.

The PCBs were pyrolysed in a fixed bed reactor at 850°C. The organic fraction released by the boards was analysed by a variety of gas chromatography techniques. The residue that remained after pyrolysis was analysed by ICP‐MS to determine the type of metals that were present.

When PCBs were heated to 800°C in an oxygen free atmosphere, the organic fraction decomposed to form volatile oils and gases leaving behind the metal and glass fibre fraction of the boards. The pyrolysed boards were very friable and the different fractions (metal components, copper power boards, glass fibre, etc.) could be easily separated. The recovered metals could then be recycled by traditional routes with particular emphasis being placed on the recovery and recycling of rare and precious metals. The organic oils and gases which are produced during pyrolysis of PCBs can either be used as a chemical feedstock or as a fuel.

The research was only carried out on a very small scale so an investigation into scale‐up must be performed.

By using pyrolysis, the organic and metallic fraction of PCBs can be separated and recycled.

This paper presents a novel method for resource recovery from PCBs.

In 2008, a number of Southern African countries cultivated about 900,000 ha of Jatropha, with a number of biodiesel plants ready for production; however, none of the projects succeeded. In 2014, KiOR advanced biofuel Energy Company in the USA announced bankruptcy due to incompetent technology. Studies disclose that the reasons for biofuel plants failure are not only due to lack of incentives and unclear policies but also due to lack of economic feasibility and low production yields. This paper aims to review the techno-economy assessment of second-generation biofuel technologies. The purpose of this paper is to summarize specific techno-economic indicators such as production cost, technology efficiency and process life cycle analysis for advanced biofuel technology and to narrate and illustrate a clear view of what requires assessment to deploy a feasible advanced biofuel technology. This study also reviews assessment of biomass supply chain, feedstock availability and site selection criteria. The review also elaborates on the use of different processes, forecasting and simulation-modeling tools used in different techno-economic analysis studies. The review provides guidance for conducting a technical and economic feasibility study for the advanced biofuels energy business.

The aim of this review is, therefore, to evaluate the techno-economic feasibility studies for the establishment of viable industrial scale production of second-generation biofuels. It does so by grouping studies based on technology selection, feedstock availability and suitability, process simulation and economies as well as technology environmental impact assessment.

In conclusion, techno-economic analysis tools offer researchers insight in terms of where their research and development should focus, to attain the most significant enhancement for the economics of a technology. The study patterns within the scope of techno-economics of advanced biofuel reveal that there is no generic answer as to which technology would be feasible at a commercial scale. It is therefore important to keep in mind that models can only simplify and give a simulation of reality to a certain extent. Nevertheless, reviewed studies do not reach the same results, but some results are logically similar.

The originality of this article specifically illustrates important technical and economic indicators that should be considered when conducting feasibility studies for advance biofuels.

A systems perspective of waste management allows an integrated approach not only to the five basic functional elements of waste management itself (generation, reduction, collection, recycling, disposal), but to the problems arising at the interfaces with the management of energy, nature conservation, environmental protection, economic factors like unemployment and productivity, etc. This monograph separately describes present practices and the problems to be solved in each of the functional areas of waste management and at the important interfaces. Strategies for more efficient control are then proposed from a systems perspective. Systematic and objective means of solving problems become possible leading to optimal management and a positive contribution to economic development, not least through resource conservation. India is the particular context within which waste generation and management are discussed. In considering waste disposal techniques, special attention is given to sewage and radioactive wastes.

In 1987, Campbell Soup Company introduced the Souper Combo, a line of frozen soup and sandwiches. Melvin Druin, vice‐president for packaging, called it “the perfect combination of old‐fashioned good taste and today's convenience. No mess. No fuss. Easy to use. All you have to do is clean your spoon. Everything else just throw away.” Unfortunately, the multi‐layered plastic‐coated packaging does not just disappear when thrown away. Plastics packaging, particularly from convenience products, has become a waste disposal nightmare. Garbage, an environmental magazine, gave the Souper Combo an “in the dumpster” award, saying, “It's precisely the kind of product that's created the municipal landfill monster.”

Plastic waste is one of the long-standing global issues in the recent era. Unfortunately, India is one of the countries which has been affected by the mismanagement of the use of plastics. India has recorded a substantial growth in the production of plastic and is considered a country of increased consumption of plastic. Due to the absence of an appropriate waste collection and segregation process, it has created the major issue of waste management and discarded used plastic items used for packaging application. There are various plastic waste management laws and programmes that have a cascading effect on almost every sector of business. In 2016, two years after the new union government took power in New Delhi, The Ministry of Environment, Forest and Climate Change (MoEFCC) has made some improvements in rules for the collection, segregation, processing, treatment and disposal of the waste. In the pandemic era, effective plastic waste management became more important than ever. The COVID-19 pandemic has created an increased demand for single-use plastic because of pressure on the already out-of-control global plastic waste problem. It is recorded to be large, and the magnitude of this pandemic related to mismanaged plastic waste is unknown. However, understanding the changing landscape and alarming need for effective plastic waste management, the government of India has proposed certain changes to prohibit imports, handling, manufacturing and use of single-use plastics in the country. This is in line with the government's intent to phase out single-use plastic by 2022. Considering this, this chapter highlights the changes in the rules and regulations in India related to plastic waste management and its effects on various sectors of business.