Search results

The purpose of this paper is to present issues related to the design of a modern lighting system based on LED technology. The developed system provides lighting with a high colour rendering index (up to 98); it also has many innovative functions, which make its implementation bring significant energy savings and increase the comfort of work.

In contrast to typical solutions, the dynamic synthesis of white light from six component colours was used in the presented project. This process is controlled by a microcontroller, and there is a colour temperature sensor in the feedback loop. The communication between smart luminaires and sensor modules is provided by means of a ZigBee wireless network.

The correctness of the proposed methodology has been proved by measurements and laboratory tests.

The process of improving the lighting system is continued and significant changes in the spectrum of used sensors are expected.

The proposed system based on mixing light from six components is an innovative solution that besides undoubted advantages entails a more elaborate electronic circuitry. However, good characteristics of the obtained light, as well as the possibility of compensating for changes in colour temperature of natural light and reducing the impact of aging of LEDs, in the authors’ opinion, make the proposed solution find its place on the market.

The proposed solution is original, both in terms of the light mixing technique and advanced functionality offered by the system.

The purpose of the paper was to present a comparative study on the microstructure and magnetoelectric effect of new magnetoelectric composites based on TbFe₂ compound and Ni_0.3Zn_0.62Cu_0.08Fe₂O₄, CoFe₂O₄ ferrites as a magnetostrictive phase, Pb(Fe_1/2Ta_1/2)O₃ (PFT), Pb(Fe_1/2Nb_1/2)O₃ relaxors as a ferroelectric phase and polyvinylidene fluoride (PVDF) as piezoelectric phase.

The ceramic components of composites were prepared by the standard solid-state reaction method. The intermetallic compound TbFe₂ was prepared with an arc melting system with a contact-less ignition in a high purity argon atmosphere. The metal – ceramic – polymer composites were prepared in a container in which powder of PVDF were dissolved in N,N-dimethylformamide with continuous mixing and at the controlled temperature. Ceramic composites were prepared as bulk samples and multilayer tape cast and co-sintered laminates. The microstructure of the composites was investigated using scanning electron microscopy (SEM). The magnetoelectric effect of the composites was evaluated at room temperature by means of the dynamic lock-in method.

SEM analysis revealed a dense, fine-grained microstructure and uniform distribution of the metallic, ferrite and relaxor grains in the bulk composites. The SEM image for multilayer composite illustrates the lack of cracks or delaminations at the phase boundaries between the well-sintered ferrite and relaxor layers. For all studied composites, the magnetoelectric coefficients at a lower magnetic field increase, reaches a maximum and then decreases.

The progress in electronic technology is directly linked to advances made in materials science. Exploring and characterizing new materials with interesting magnetoelectric properties, in the rapidly growing field of functional materials, is an important task. The paper reports on processing, microstructure and magnetoelectric properties of novel magnetoelectric composites.

The purpose of this paper is to assess the reliability of thermoelectric generators after ageing at elevated temperature and to determine the influence of the technology used (i.e. type of thermoelectric material, type of substrate and soldering technology) for thermogenerator (TGE) assembly.

In this paper, the Seebeck coefficient and the current voltage were measured for lead telluride doped with either manganese (PMT), germanium (PGT) or sulfur (PST) TGEs. The Seebeck coefficient measurements were taken at temperatures between 230 and 630 K.

The Seebeck coefficient determined for PMT, PGT and PST TGEs increases approximately linearly with increasing temperature and is greater by about 40 per cent for PST and about 30 per cent for PMT than in commercially available PbTe TGEs. The best outcome in terms of stability after long-term ageing was that of PMT material.

The choice of proper technology (i.e. thermoelectric materials, type of substrate and soldering technology) for the TGE assembly is essential for their functioning overtime and reliability.

This paper aims to present certain issues in direct bonded copper (DBC) technology towards the manufacture of Al2O3 or AlN ceramic substrates with one or both sides clad with a copper (Cu) layer.

As part of the experimental work, attempts were made to produce patterns printed onto DBC substrates based on four substantially different technologies: precise cutting with a diamond saw, photolithography, the use of a milling cutter (LPKF ProtoMat 93s) and laser ablation with differential chemical etching of the Cu layer.

The use of photolithography and etching technology in the case of boards clad with a 0.2-mm-thick Cu layer, can produce conductive paths with a width of 0.4 mm while maintaining a distance of 0.4 mm between the paths, and in the case of boards clad with a 0.3-mm-thick copper layer, conductive paths with a width of 0.5 mm while maintaining a distance of 0.5 mm between paths. The application of laser ablation at the final step of removing the unnecessary copper layer, can radically increase the resolution of printed pattern even to 0.1/0.1 mm. The quality of the printed pattern is also much better.

Etching process optimization and the development of the fundamentals of technology and design of power electronic systems based on DBC substrates should be done in the future. A limiting factor for further research and its implementation may be the relatively high price of DBC substrates in comparison with typical PCB printed circuits.

Several examples of practical implementations using DBC technology are presented, such as full- and half-bridge connections, full-wave rectifier with an output voltage of 48 V and an output current of 50 A, and part of a battery discharger controller and light-emitting diode illuminator soldered to a copper heat sink.

The paper presents a comparison of different technologies used for the realization of precise patterns on DBC substrates. The combination of etching and laser ablation technologies radically improves the quality of DBC-printed patterns.