Search results

This study aims to investigate the potential use of potato peel extracts as antibacterial finishes for cotton fabrics against Staphylococcus aureus and Escherichia coli. Potato peels are abundant as waste and provide a natural, cheaper and sustainable alternative means of preventing the spread of bacterial infections on cotton fabric.

This research included the characterization of potato peel extracts, application of the extract onto cotton fabric and efficacy testing of the treated cotton fabric against bacteria. Phytochemical screening, agar well diffusion antibacterial test, minimum inhibitory concentration and Fourier transform infrared (FTIR) tests were used to characterize the extract. Antibacterial efficacy of the treated fabric was determined qualitatively using the disc diffusion assay and quantitatively using the bacteria reduction test.

Phytochemical screening confirmed the presence of several secondary metabolites including phenols and flavonoids. Antibacterial tests revealed a positive response in Escherichia coli and Staphylococcus aureus with a zone of inhibition of 6.50 mm and 5.60 mm, respectively. Additional peaks on the FTIR spectroscopy confirmed the presence of potato peel extract on the treated cotton fabric. The treated cotton fabrics showed efficacy against Staphylococcus aureus and Escherichia coli up to 20 washes.

This study introduced the application of potato peel extracts onto cotton fabrics and assessment of the antibacterial properties before and after washing. Results of this study suggest that potato peel extracts can be used as an organic eco-friendly antibacterial finish for cotton fabrics.

This study aims to assess the effect of water variation on bioethanol production from cassava peels (CP) using Saccharomyces cerevisiae yeast as the ethanologenic agent.

The milled CP was divided into three treatment groups in a small-scale flask experiment where each 20 g CP was subjected to two-stage hydrolysis. Different amount of water was added to the fermentation process of CP. The fermented samples were collected every 24 h for various analyses.

The results of the fermentation revealed that the highest ethanol productivity and fermentation efficiency was obtained at 17.38 ± 0.30% and 0.139 ± 0.003 gL⁻¹ h⁻¹. The study affirmed that ethanol production was increased for the addition of water up to 35% for the CP hydrolysate process.

The finding of this study demonstrates that S. cerevisiae is the key player in industrial ethanol production among a variety of yeasts that produce ethanol through sugar fermentation. In order to design truly sustainable processes, it should be expanded to include a thorough analysis and the gradual scaling-up of this process to an industrial level.

This paper is an original research work dealing with bioethanol production from CP using S. cerevisiae microbe.

1. Hydrolysis of cassava peels using 13.1 M H₂SO₄ at 100 ^oC for 110 min gave high Glucose productivity

2. Highest ethanol production was obtained at 72 h of fermentation using Saccharomyces cerevisiae

3. Optimal bioethanol concentration and yield were obtained at a hydration level of 35% agitation

4. Highest ethanol productivity and fermentation efficiency were 17.3%, 0.139 g.L⁻¹.h⁻¹

Hydrolysis of cassava peels using 13.1 M H₂SO₄ at 100 ^oC for 110 min gave high Glucose productivity

Highest ethanol production was obtained at 72 h of fermentation using Saccharomyces cerevisiae

Optimal bioethanol concentration and yield were obtained at a hydration level of 35% agitation

Highest ethanol productivity and fermentation efficiency were 17.3%, 0.139 g.L⁻¹.h⁻¹

Agricultural waste and food sources are some of the pollutants of the environment. One of these wastes is the peel of fruits that cannot be consumed as food. In this regard, walnut husk (WH) and oleaster peel (PO) are known as two important sources of tannin and are bulky wastes. Because of the high percentage of tannin, these materials can be used as a natural source for the preparation of bio-mordant in the dyeing process.

In this study, Reseda and Madder were used as natural dyes in the presence of a mixture of two bio-mordants. WH and PO were selected as bio-mordant. All natural resources are extracted to obtain the juice. The phenolic percentage of tannin-containing extracts was evaluated and then it was used for wool yarns by premordanting method. The results of evaluating the fastness properties using the ISO method.

The most important achievement of this research is the use of agricultural waste in the dyeing process to reduce environmental pollution and create added value. All compounds rich in tannin have some phenolic components, therefore the amount of phenolic content of these extracts was evaluated. The effect of mixing the mordant on the color characteristics of the yarns was investigated and the results showed that changing the ratio of the combination of two mordant is effective on the K/S values. The results of evaluating the fastness properties using the ISO method showed that the washing, rubbing and light fastness in the presence of mordant is good, good and moderate, respectively.

In this paper, to the best of the authors’ knowledge, for the first time, the combination of two natural extracts obtained from agricultural waste has been used to create a new bio-mordant on fibers and improve stability.

The paper aims to empirically test a framework to predict the desire and intention to engage with an elective health-care procedure and implement a methodology to test the anticipated positive and negative emotions in hedonic adaptation to an elective procedure.

Two studies in USA and Australia (N = 1,200) confirmed the psychometric properties of the key constructs under the chemical peel condition. Two further studies in the USA and Australia (N = 1,100) explored the research question and hypotheses in the adapted model of goal-directed behaviour under the Botox condition. A survey was self-administered to online panels who had previously engaged in such elective procedures.

The findings highlighted the pragmatic implications for communication and activation strategies to safeguard consumer interests and retain their loyalty.

From the authors’ best understanding, neither a methodology nor a theoretical framework exists to explore hedonic adaptation to recurring engagement with elective health care. A methodology and theoretical framework will highlight the mood states and factors that predict desire and intention to engage. This can advance the research on hedonic adaptation and decision-making and offer pragmatic suggestions for communication and activation strategies to safeguard consumer interests and retain their loyalty.

The purpose of this paper is to illustrate the new technical demands and reliability challenges to printed circuit board (PCB) designs, materials and processes when the transmission frequency increases from Sub-6 GHz in previous generations to millimeter (mm) wave in fifth-generation (5G) communication technology.

The approach involves theoretical analysis and actual case study by various characterization techniques, such as a stereo microscope, metallographic microscope, scanning electron microscope, energy dispersive spectroscopy, focused ion beam, high-frequency structure simulator, stripline resonator and mechanical test.

To meet PCB signal integrity demands in mm-wave frequency bands, the improving proposals on copper profile, resin system, reinforcement fabric, filler, electromagnetic interference-reducing design, transmission line as well as via layout, surface treatment, drilling, desmear, laminating and electroplating were discussed. And the failure causes and effects of typical reliability issues, including complex permittivity fluctuation at different frequencies or environments, weakening of peel strength, conductive anodic filament, crack on microvias, the effect of solder joint void on signal transmission performance and soldering anomalies at ball grid array location on high-speed PCBs, were demonstrated.

The PCB reliability problem is the leading factor to cause failures of PCB assemblies concluded from statistical results on the failure cases sent to our laboratory. The PCB reliability level is very essential to guarantee the reliability of the entire equipment. In this paper, the summarized technical demands and reliability issues that are rarely reported in existing articles were discussed systematically with new perspectives, which will be very critical to identify potential reliability risks for PCB in 5G mm-wave applications and implement targeted improvements.

This study aims to investigate the effects of process input parameters (welding current, welding time, electrode pressure and holding time) on the output responses (nugget diameter, peak load and indentation) that control the mechanical properties and quality of the joints in dissimilar resistance spot welding (RSW) for the third generation of advanced high-strength steel (AHSS) quenching and partitioning (Q&P980) and (SPFC780Y) high-strength steel spot welds.

Design of experiment approach with two level factors and center points was adopted. Destructive peel and shear tensile strengths were used to measure the responses. The significant factors were determined using analysis of variance implemented by Minitab 18 software. Finally, multiresponse optimization was carried out using the desirability function analysis method.

Holding time was the most significant factor influencing nugget diameter, whereas welding current had the greatest impact on peak load and indentation. Multiresponse optimization revealed that the optimal settings were a welding current of 12.5 KA, welding time of 18 cycles, electrode pressure of 420 Kgf and holding time of 10 cycles. These settings produced a nugget diameter of 8.0 mm, a peak load of 35.15 KN and an indentation of 22.5%, with a composite desirability function of 0.764.

This study provides an effective approach for multiple response optimization to the mechanical behavior of RSW joints, even though there have been few studies on the third generation of AHSS joints and none on the dissimilar joints of the materials used in this study.

Globally, consumer’s inclination towards functional foods had noticed due to their greater health consciousness coupled with enhanced health-care cost. The fact that probiotics could promote a healthier gut microbiome led projection of probiotic foods as functional foods and had emerged as an important dietary strategy for improved human health. It had established that ice cream was a better carrier for probiotics than fermented milked due to greater stability of probiotics in ice cream matrix. Global demand for ice cream boomed and probiotic ice cream could have been one of the most demanded functional foods. The purpose of this paper was to review the technological aspects and factors affecting probiotic viability and to standardize methodology to produce functional probiotic ice cream.

Attempt was made to search the literature (review and researched papers) to identify diverse factors affecting the probiotic viability and major technological challenge faced during formulation of probiotic ice cream. Keywords used for data searched included dairy-based functional foods, ice cream variants, probiotic ice cream, factors affecting probiotic viability and health benefits of probiotic ice cream.

Retention of probiotic viability at a level of >10⁶ cfu/ml is a prerequisite for functional probiotic ice creams. Functional probiotic ice cream could have been produced with the modification of basic mix and modulating technological parameters during processing and freezing. Functionality can be further enhanced with the inclusion of certain nutraceutical components such as prebiotics, antioxidant, phenolic compounds and dietary fibres. Based upon reviewed literature, suggested method for the manufacture of functional probiotic ice cream involved freezing of a probiotic ice cream mix obtained by blending 10% probiotic fermented milk with 90% non-fermented plain ice cream mix for higher probiotic viability. Probiotic ice cream with functional features, comparable with traditional ice cream in terms of technological and sensory properties could be produced and can crop up as a novel functional food.

Probiotic ice cream with functional features may attract food manufacturers to cater health-conscious consumers.

The purpose of this study is to prepare thermal transfer ribbons with good alcohol resistance.

A variety of alcohol-resistant thermal transfer inks were prepared using different polyester resins. The printing temperature, printing effect, adhesion and alcohol resistance of the inks on the label were studied to determine the feasibility of using the ink for manufacturing thermal transfer ribbons. The ink formulations were prepared by a simple and stable grinding technology, and then use mature coating technology to make the ink into a thermal transfer ribbon.

The results show that the thermal transfer ink has good scratch resistance, good alcohol resistance and low printing temperature when the three resins coexist. Notably, the performance of the ribbon produced by 500 mesh anilox roller was better than that of other meshes. Specifically, the ink on the matte silver polyethylene terephthalate (PET) label surface was wiped with a cotton cloth soaked in isopropyl alcohol under 500 g of pressure. After 50 wiping cycles, the ink remained intact.

The proposed method not only ensures good alcohol resistance but also has lower printing temperature and wider label applicability. Therefore, it can effectively reduce the loss of printhead and reduce production costs, because of the low printing temperature.

The purpose of this research is to identify and investigate some natural dyes with halochromic properties for potential use as food spoilage indicators to reduce waste and curve the negative effects of food borne diseases.

Exactly 10 potential dye-yielding plants were selected based on their colour (mostly purple, red, maroon and pink). Solvent extraction was used to extract the dyes and pH differential method was used to determine the concentrations of anthocyanin in the extracted dyes. Different concentrations of hydrochloric acid and sodium hydroxide (0.1 M, 1 M and 2 M) in drops and in excess as acidic and basic solution, respectively, were used to test the halochromicity of the extracted dyes. Methyl red (a synthetic dye) was used as a reference standard/control. The pH of the dyes was recorded before and after addition of both NaOH and HCl solutions.

Five out of the 10 dyes extracted (labelled as dye A–E for Ti plant (green Cordyline fruticosa), coleus (Coleus blumei), paper flower (Bougainvillea glabra), painted nettle (Palisandra coleus) and purple heart (Setcresea purpurea), respectively, were found to be halochromic (even at low doses) by changing its colour when exposed to both acidic and basic solutions. While other dyes labelled F–J for red acalypha (Acalypha wilkesiana), golden shower (Cassia fistula), golden dew drop (Duranta repens), wild sage (Lantana camara var Aculeata) and pink oleander (Apocynaceae Nerium oleander), respectively, were either completely insensitive to the solutions in drops, slightly sensitive at high doses or the colour change is insignificant. Although some dyes were found to be more sensitive than others but in most cases, the colour changes in halochromic dyes were more stable in acidic conditions than in basic making it more sensitive to the basic than the acidic solution with the exception of dye A and E (to some extent) which was sensitive to both acidic and basic solution. The anthocyanin contents of dye A–J were found to be between the range of 2.28–10.35 mg/l with dye E having the lowest and dye J with the highest anthocyanin concentration, respectively. The initial pH of all the dyes falls within the range of 4.8–7.3 with most found within the acidic range.

Halochromic dye research studies are still at the infancy stage in developing world despite the vast available and abundant potential natural halochromic dye-yielding plants. The study explored this area of research and gives an opportunity for the development of smart packaging for pH-sensitive foods using natural dyes as an alternative to conventional synthetic dyes to reduce cost and also curve the negative effect of synthetic dyes as well as food borne diseases.

In addition to agriculture, energy production, and industries, potable water plays a significant role in many fields, further increasing the demand for potable water. Purification and desalination play a major role in meeting the need for clean drinking water. Clean water is necessary in different areas, such as agriculture, industry, food industries, energy generation and in everyday chores.

The authors have used the different search engines like Google Scholar, Web of Science, Scopus and PubMed to find the relevant articles and prepared this mini review.

The various stages of water purification include coagulation and flocculation, coagulation, sedimentation and disinfection, which have been discussed in this mini review. Using nanotechnology in wastewater purification plants can minimize the cost of wastewater treatment plants by combining several conventional procedures into a single package.

In society, we need to avail clean water to meet our everyday, industrial and agricultural needs. Purification of grey water can meet the clean water scarcity and make the environment sustainable.

This mini review will encourage the researchers to find out ways in water remediation to meet the need of pure water in our planet and maintain sustainability.