Search results

The aim of this study was to evaluate the feasibility of pad printing for producing electrical conductors and to define the factors affecting the print quality of polymeric silver ink conductors.

Polyethylene terephthalate (PET) film and polyphenylene oxide (PPO) compound film were used as substrate materials. Three different polymeric silver inks, marked A, B and C, were used and tested.

The results indicated that the important factors in the pad printing of silver ink conductors are the printing parameters and characteristics of the ink, pad, cliché and substrate. The interactions of these factors should be considered on a case-by-case basis. The sheet resistances of triple-pressed ink conductors varied between 20 and 110 mΩ/sq for 5.7- to 8.5-μm-thick conductors. Ink (B) had a higher sheet resistance than Ink (A) because of its lower silver particle content but also because of the shorter curing time and lower curing temperature. Ink (A) showed excellent adhesion on PET, and Ink (B) had moderate adhesion on PET without corona or plasma pre-treatments, but both inks adhered weakly on PPO compound. Both corona and plasma treatments raised adhesion of these two inks on all test substrates to the highest classification value, 5B.

This paper contains a survey and preliminary testing of the pad printing of polymeric silver ink conductors on flexible thermoplastic foils. Finally, the paper introduces the advantages and drawbacks of the technique.

The purpose of this paper is to investigate and minimize the printing-related defects in the surface mount assembly (SMA) process.

This paper uses an experimental approach to explore process parameter and printing defects during the SMA process. Increasing printing performance, various practices of solder paste (Ag3.0/Cu0.5/Sn) storage and handling are suggested. Lopsided paste problem is studied by varying squeegee pressure and the results are presented. Unfilled pads problems are observed for ball grid array (BGA) and quad flat package (QFP) which is mitigated by proper force tuning. In this paper, a comparative study is conducted which evaluates the manifestation of printing offset due to low-grade stencil. The input/output (I/O) boards were oxidized when the relative humidity was maintained beyond 70 per cent for more than 8 h. This pad oxidation problem is overcome by proper printed circuit board (PCB) handling procedures. When the unoptimized line is used, the paste wedged in the stencil and influences the performance of the screen printer, for this reason, an optimized line is proposed that minimize the printing defects.

The key findings are as follows: in the SMA process, printing quality is directly associated with solder paste quality. Experimentally, it is observed that a considerable variance in solder deposition occurred when the front and rear squeegee have different configurations. High-grade and unsoiled stencil results in superior paste deposition and less distinction. Insufficient solder paste and bridge problems also occur in printing when PCB pads are oxidized. Optimized line resolves solder paste clog issues, associated with stencil’s aperture. The cooling arrangement on the conveyor, after reflow, explicates hot jig problem. Control environmental conditions minimized static charges and printing defects.

The preceding studies emphasis mostly on the squeegee pressure, while other important parameters are not completely investigated. Moreover, it is very imperative to concurrently measure all parameters while varying the environmental conditions. This study highlights and provides an experimental approach to various PCB printing defects, and a comparative study has been conducted that concurrently measure all process parameters.

The purpose of this paper is to study the effect of the electropolishing time of stencil manufacturing parameters and solder‐mask definition methods of PCB pad design parameters on the performance of solder paste stencil printing process for the assembly of 01005 chip components.

During the study, two types of stencils were manufactured for the evaluations: electroformed stencils and electropolished laser‐cut stencils. The electroformed stencils were manufactured using the standard electroforming process and their use in the paste printing process was compared against the use of an electropolished laser‐cut stencil. The electropolishing performance of the laser‐cut stencil was evaluated twice at the following intervals: 100 s and 200 s. The performance of the laser‐cut stencil was also evaluated without electropolishing. An optimized process was established after the polished stencil apertures of the laser‐cut stencil were inspected. The performance evaluations were made by visually inspecting the quality of the post‐surface finishing for the aperture wall and the quality of that post‐surface finishing was further checked using a scanning electron microscope. A test board was used in a series of designed experiments to evaluate the solder paste printing process.

The results demonstrated that the length of the electropolishing time had a significant effect on the small stencil's aperture quality and the solder paste's stencil printing performance. In this study, the most effective electropolishing time was 100 s for a stencil thickness of 0.08 mm. The deposited solder paste thickness was significantly better for the enhanced laser‐cut stencil with electropolishing compared to the conventional electroformed stencils. In this printing‐focused work, print paste thickness measurements were also found to vary across different solder‐mask definition methods of printed circuit board pad designs with no change in the size of the stencil aperture. The highest paste value transfer consistently occurred with solder‐mask‐defined pads, when an electropolished laser‐cut stencil was used.

Due to important improvements in the quality of the electropolished laser‐cut stencil, and based on the results of this experiment, the electropolished laser‐cut stencil is strongly recommended for the solder paste printing of fine‐pitch and miniature components, especially in comparison to the typical laser‐cut stencil. The advantages of implementing a 01005 chip component mass production assembly process include excellent solder paste release, increased solder volume, good manufacture‐ability, fast turnaround time, and greater cost saving opportunities.

This paper aims to study the packing density of printed paths on different substrate materials. It presents problems which appear when the necessity of printing one or more narrow paths occurs.

A piezoelectric printhead containing nozzles with a diameter of 35 µm was used for printing nanoparticle silver ink on different polymer substrates which were treated by plasma or not treated at all. The shape, defects, resistance and printing parameters for the printed paths were analysed.

The obtained results allow the identification of the sources of the technological problems in obtaining a high packing density of the paths in a small area of substrate and the repeatable prints.

The study could have limited universality because of the chosen research method; printhead, ink, substrate materials and process parameters were arbitrarily selected. The authors encourage the study of other kinds of conductive inks, treatment methods and printing process parameters.

The study includes practically useful information about widths, shapes, defects and the resistance of the paths printed using different technological parameters.

The study presents the results of original empirical research on problems of the packing density of inkjet printed paths on a small area of substrate and identifies problems that must be resolved to obtain effective interconnections in the inkjet technology.

The purpose of this paper is to investigate the durability of radio‐frequency identification (RFID) chips assembled on flexible substrates (paper and foil), with materials evaluated with regard to mechanical stresses and dependence on the applied substrate, antenna materials, chip pad printing and chip encapsulation.

RFID chips were assembled to antennas screen printed on flexible substrates. Shear and bending tests were conducted in order to evaluate the mechanical durability of the chip joints depending on the materials used for mounting the RFID chip structures. X‐ray inspection and cross sectioning were performed to verify the quality of the assembly process. The microstructure and the resistance of the materials used for chip pads were investigated with the aim of determining the conductivity mechanism in the printed layers.

Addition of carbon nanotubes to the conductive adhesive (CA) provided a higher shear force for the assembled RFID chips, compared to the unmodified conductive adhesive or a polymer paste with silver flakes. However, this additive resulted in an increase in the material's resistance. It was found that the RFID substrate material had a significant influence on the shear force of mounted chips, contrary to the materials used for printing antennas. The lower shear force for chips assembled on antennas printed on paper rather than on foil was probably connected with its higher absorption of solvent from the pastes. Increasing the curing temperature and time resulted in an additional increase in the shear force for chips assembled to antennas printed on foil. A reverse dependence was observed for chips mounted on the antennas made on paper. An improvement in the durability of the RFID chip structures was achieved by chip encapsulation. Bending tests showed that a low‐melting adhesive was the best candidate for encapsulation, as it provided flexibility of the assembled structure.

Further studies are necessary to investigate the mechanical durability of RFID chips assembled with a conductive adhesive, with different addition levels and types of carbon nanotubes.

The results revealed that the best candidate for providing the highest RFID chip durability related to mechanical stresses was the low‐melting adhesive. It can be recommended for practical use, as it simplified the assembly process and reduced the curing step in the encapsulation of the RFID devices. From the results of shear testing, conductive adhesives with carbon nanotubes can be used in RFID chip assembly because of their ability to increase the shear force of joints created between the antenna and the chip.

In this paper, the influence of the materials used for antenna, chip pads, encapsulation and the curing conditions on the mechanical durability (shear and bending) of RFID chips was analyzed. Commercial and elaborated materials were compared. Some new materials containing a conductive adhesive and carbon nanotubes were proposed and tested in RFID chip assembly to antennas printed on flexible substrates (paper and foil).

The increasing availability and use of fine pitch integrated circuit packages place increased demands on the stencil printing process for solder paste deposition. To attain the resolution needed for high assembly yields, both materials and operating parameters must be optimised. The resultant deposits must be uniform and of the proper geometry to promote satisfactory device placement and reflow. This paper summarises findings in the following areas:

Experimental design has proved to be a useful statistical tool in reducing process variation. The technique has been applied to a wide range of processes, including electronics assembly and soldering processes. For effective SMT assembly the screen printing of solder paste requires tight process control, especially as pad geometries become ever smaller. However, printing of solder paste is a rather complex process which is affected by machine, material, environmental and human factors, which make it difficult to characterise effectively. This paper examines the practical application of experimental design to solder paste printing for SMT and also the results from a number of experiments carried out on a semi‐automatic ‘clamshell’ type screen printer. The experimentation concentrates on the important printer and squeegee parameters and their effect on paste deposition, with measured solder paste height and ‘measle’ diagrams used as process outputs. The usefulness of the experimental results in determining the best printer settings, as well as the problems encountered during the experimentation, are highlighted.

The purpose of this paper is to suggest an analysis methodology for the stencil printing process and to obtain proper design parameters that guarantee the successful filling using suggested finite element analyses.

Filling performance of solder paste in the stencil printing process is highly dependent on material properties such as viscosity and surface tension together with process parameters such as squeegee angle and squeegee speed. In order to investigate the effects of process parameters on the filling performance, the pressure built‐up under the squeegee and the filling procedure of the solder paste into an aperture were analysed. Due to the limitations of the computational memory and time, the analysis domain was simplified. The pressure development under the squeegee was investigated for various values of squeegee angle and speed; then, the filling behaviour with the pressure boundary condition was analysed for only one aperture. Finally, the two analysis results were integrated to obtain the successful filling condition. In this analysis method, process parameters that guarantee filling performance were decided on.

It was shown that higher squeezing pressure develops as the squeegee angle decreases and the squeegee speed increases. The filling performance, however, improves as the squeegee angle and the squeegee speed decrease. This is because the pressure duration time decreases as the squeegee speed increases.

This study suggests a new design approach to obtain proper process design parameters for successful filling of solder paste into an aperture. The direct analysis of filling with squeegee movement is impossible due to limitations of computer memory and computation time. To overcome these limitations, a two steps analysis approach is proposed and can be effectively applied in the design of stencil screen printing.

Historically, tin‐lead solder has been a commonly used joining material in electronics manufacturing. Environmental and health concerns, due to the leaching of lead from landfills into ground water, have necessitated legislation that restricts the use of lead in electronics. The transition from tin‐lead solder to a lead‐free solder composition is imminent. Several alternative solder alloys (and their fluxes) have been researched for electronics assembly in the last few years. The objective of this research was to develop a systematic selection process for choosing a “preferred” lead‐free solder paste, based on its print and reflow performance.

After a detailed study of industry preferences, published experimental data, and recommendations of various industrial consortia, a near eutectic tin‐silver‐copper (SAC) composition was selected as the preferred alloy for evaluation. Commercially available SAC solder pastes with a no‐clean chemistry were extensively investigated in a simulated manufacturing environment. A total of nine SAC pastes from seven manufacturers were evaluated in this investigation. A eutectic Sn/Pb solder paste was used as a baseline for comparison. While selecting the best lead‐free paste, it was noted that the selected paste has to perform as good as, if not better than, the current tin‐lead paste configuration used in electronics manufacturing for a particular application. The quality of the solder pastes was characterized by a series of analytical and assembly process tests consisting of, but not limited to, a printability test, a solder ball test, a slump test, and post reflow characteristics such as the tendency to form voids, self‐centring and wetting ability.

Each paste was evaluated for desirable and undesirable properties. The pastes were then scored relative to each other in each individual test. An aggregate of individual test scores determined the best paste.

This paper summarizes a systematic approach adopted to evaluate lead‐free solder pastes for extreme reflow profiles expected to be observed in reflow soldering lead‐free boards.

This study aims to focus on the surface mount technology (SMT) mass production process of Sn-9Zn-2.5Bi-1.5In solder. It explores it with some components that will provide theoretical support for the industrial SMT application of Sn-Zn solder.

This study evaluates the properties of solder pastes and selects a more appropriate reflow parameter by comparing the microstructure of solder joints with different reflow soldering profile parameters. The aim is to provide an economical and reliable process for SMT production in the industry.

Solder paste wettability and solder ball testing in a nitrogen environment with an oxygen content of 3,000 ppm meet the requirements of industrial production. The printing performance of the solder paste is good and can achieve a printing rate of 100–160 mm/s. When soldering with a traditional stepped reflow soldering profile, air bubbles are generated on the surface of the solder joint, and there are many voids and defects in the solder joint. A linear reflow soldering profile reduces the residence time below the melting point of the solder paste (approximately 110 s). This reduces the time the zinc is oxidized, reducing solder joint defects. The joint strength of tin-zinc joints soldered with the optimized reflow parameters is close to that of Sn-58Bi and SAC305, with high joint strength.

This study attempts to industrialize the application of Sn-Zn solder and solves the problem that Sn-Zn solder paste is prone to be oxidized in the application and obtains the SMT process parameters suitable for Sn-9Zn-2.5Bi-1.5In solder.