Search results

Incineration has become increasingly important in many large cities around the world because of fast urbanization and population growth. The benefits of energy production and large reduction in the waste volume to landfills also contribute to its growing adaptation for solid waste management for these cities. At the same time, the environmental impact of the pollutant gases emitted from the incineration process is a common concern for various stakeholders which must be properly addressed. To minimize the pollutant gas emission levels, as well as maximize the energy efficiency, it is critically important to optimize the combustion performance of an incinerator freeboard which would require the development of reliable approaches based on computational fluid dynamics (CFD) modeling. A critical task in the CFD modeling of an incinerator furnace requires the specification of waste characteristics along the moving grate as boundary conditions, which is not available in standard CFD packages at present. This study aims to address this gap by developing a numerical incinerator waste bed model.

A one-dimensional Lagrangian model for the incineration waste bed has been developed, which can be coupled to the furnace CFD model. The changes in bed mass due to drying, pyrolysis, devolatilization and char oxidation are all included in the model. The mass and concentration of gases produced in these processes through reactions are also predicted. The one-dimensional unsteady energy equations of solid and gas phases, which account for the furnace radiation, conduction, convection and heat of reactions, are solved by the control volume method.

The Lagrangian model is validated by comparing its prediction with the experimental data in the literature. The predicted waste bed height reduction, temperature profile and gas concentration are in reasonable agreement with the observations.

The simplicity and efficiency of the model makes it ideally suitable to be used for coupling with the computational furnace model to be developed in future (so as to optimize incinerator designs).

Micropollutants in the aquatic environment pose threats to both ecosystems and human health. Traditional wastewater treatment plants (WWTP) reduce some micropollutants, especially those who adhere to sludge or suspended matter. The hydrophilic micropollutants, on the other side, which may be non-biodegradable and resistant to UV-treatment etc. are typically transported untreated into the water recipients. This paper contains a literature study on the state of the art of advanced wastewater treatment technologies for reducing micropollutants such as pharmaceutical degradation products, personal care products, surfactants and industrial chemicals including heavy metals.

This literature study is completed using the most extensive and expansive literature database in the World to date, Google Scholar (GS). Published papers in recognized scientific journals are sought out in GS, and for relevance for this literature study, papers published here from 2016 and onwards (the last 5 years) have been chosen to eliminate irrelevant studies.

The result of the study is that there are many promising technologies on the market or emerging; however, no one solution treats every micropollutant equally well. Since advanced technologies often require expensive investments for municipalities and companies, it is important to identify which micropollutants pose the highest risk towards human health and the environment, because choosing systems to eliminate them all is not economically wise, and even choosing a system combining the existing technologies can be more expensive than states, municipalities and private companies are capable of investing in.

The research is limited to published papers on GS, which may omit certain papers published in closed databases not sharing their work on GS.

The practical implications are that practitioners cannot find go-to solutions based on the conclusions of the research and thus need to use the results to investigate their own needs further in order to make the wisest decision accordingly. However, the paper outlines the state of the art in advanced wastewater treatment and explains the benefits and downsides of the technologies mentioned; however, more research in the field is required before practitioners may find a proper solution to their specific issues.

The social implications are that the consequences of introducing a removal of micropollutants from the water environment can ultimately effect the citizens/consumers/end-users through added costs to the tariffs or taxes on advanced wastewater treatment, added costs on everyday goods, wares and products and added costs on services that uses goods, wares and products that ultimately produces micropollutants affecting the water environment.

This paper presents a much needed state of the art regarding the current advanced technologies to mitigate micropollutants in wastewater. The overview the paper provides supports politics on national as well as international levels, where larger unions such as the EU has stated that advanced wastewater treatment will be the next step in regulating pollutants for aquatic outlet.

To decrease wear and friction, zinc dialkyldithiophosphate (ZDDP) has been used in engine oil for several decades, but the mechanism of the tribofilm formation is still unclear. The purpose of this study is to characterize the chemical details of the tribofilm by using high-resolution approaching.

An ISO VG 100 mineral oil mixed with ZDDP was used in sliding tests on cylindrical roller bearings. Tribofilm formation was observed after 2 h of the sliding test. X-ray photoelectron spectroscopy (XPS) and atom probe tomography (APT) were used for chemical analysis of the tribofilm.

The results show that the ZDDP tribofilm consists of the common ZDDP elements along with iron oxides. A considerable amount of zinc and a small amount of sulfur were observed. In particular, an oxide interlayer with sulfur enrichment was revealed by APT between the tribofilm and the steel substrate. The depth profile of the chemical composition was obtained, and a tribofilm of approximately 40 nm thickness was identified by XPS.

A sulfur enrichment at the interface is observed by APT, which is beneath an oxygen enrichment. The clear evidence of the S interlayer confirms the hard and soft acids and bases principle.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2020-0035/

The main purpose of this study resides essentially in the development of a new tool to quantify the biomass in the bioreactor operating under steady state conditions.

Modeling is the most relevant tool for understanding the functioning of some complex processes such as biological wastewater treatment. A steady state model equation of activated sludge model 1 (ASM1) was developed, especially for autotrophic biomass (XBA) and for oxygen uptake rate (OUR). Furthermore, a respirometric measurement, under steady state and endogenous conditions, was used as a new tool for quantifying the viable biomass concentration in the bioreactor.

The developed steady state equations simplified the sensitivity analysis and allowed the autotrophic biomass (XBA) quantification. Indeed, the XBA concentration was approximately 212 mg COD/L and 454 mgCOD/L for SRT, equal to 20 and 40 d, respectively. Under the steady state condition, monitoring of endogenous OUR permitted biomass quantification in the bioreactor. Comparing XBA obtained by the steady state equation and respirometric tool indicated a percentage deviation of about 3 to 13%. Modeling bioreactor using GPS-X showed an excellent agreement between simulation and experimental measurements concerning the XBA evolution.

These results confirmed the importance of respirometric measurements as a simple and available tool for quantifying biomass.

Exposure therapy is a widely used treatment for patients with post-traumatic stress dis -order. It involves reduction of fear through progressive exposure to frightening stimuli in a therapeutic environment. Here we propose a new method designed to improve the effectiveness of exposure therapy. We hypothesized that device-guided breathing during exposure therapy can increase the capability of the patient to undergo effective exposure. The successful application of the method is described for a single patient. Using a device to slow and regularize breathing, the patient was calmed and experienced a greater sense of control and a profound effect of the exposure. The use of the breathing-guiding device is believed to reduce arousal level and excitability of sympathetic “fight-flight” behaviors. The present study suggests that device-guided breathing integrated with exposure therapy may provide a practically feasible and potentially promising non-pharmacological treatment after trauma.

While aiming to create methods for fibre recycling, the question of colours in waste textiles is also in focus; whether the colour should be kept or should be removed while recycling textile fibre. More knowledge is needed for colour management in a circular economy approach.

The research included the use of different dye types in a cotton dyeing process, the process for decolourizing and the results. Two reactive dyes, two direct dyes and one vat dye were used in the study. Four chemical treatment sequences were used to evaluate colour removal from the dyed cotton fabrics, namely, HCE-A, HCE-P-A, HCE-Z-P-A and HCE-Y-A.

The objective was to evaluate how different chemical refining sequences remove colour from direct, reactive and vat dyed cotton fabrics, and how they influence the specific cellulose properties. Dyeing methods and the used refining sequences influence the degree of colour removal. The highest achieved final brightness of refined cotton materials were between 71 and 91 per cent ISO brightness, depending on the dyeing method used.

Only cotton fibre and three different colour types were tested.

With cotton waste, it appears to be easier to remove the colour than to retain it, especially if the textile contains polyester residues, which are desired to be removed in the textile refining stage.

Colour management in the CE context is an important new track to study in the context of the increasing amount of textile waste used as a raw material.