Search results

The purpose of this study is two phase modeling of Water/Cu nanofluid forced convection in different arrangements of elliptical tube banks in a two-dimensional space.

The arrangements of tube banks have been regarded as equal spacing triangle (ES), equilateral triangle (ET) and the rotated square (RS). The obtained results indicate that, among the investigated arrangements, the RS arrangement has the maximum value of heat transfer with cooling fluid. Also, the changes of Nusselt number and the local friction factor are under the influence of three main factors including volume fraction of slid nanoparticles, the changes of fluid velocity parameters on the curved surface of tube and flow separation after crossing from a specified angle of fluid rotation.

In Reynolds number of 250 and in all arrangements of the tube banks, the behavior of Nusselt number is almost the same and the separation of flow happens in almost 155-165 degrees from fluid rotation on surface. In RS arrangement, due to the strength of vortexes after fluid separation, better mixture is created and because of this reason, after the separation zone, the level of local Nusselt number graph enhances significantly.

In this research, the laminar and two-phase flow of Water/Cu nanofluid in tube banks with elliptical cross section has been numerically investigated in a two-dimensional space with different longitudinal arrangements. In this study, the effects of using nanofluid, different arrangements of tube banks and the elliptical cross section on heat transfer and cooling fluid flow among the tube banks of heat exchanger have been numerically simulated by using finite volume method.

Although many studies have been conducted on the nanofluid flow in microtubes, this paper, for the first time, aims to investigate the effects of nanoparticle diameter and concentration on the velocity and temperature fields of turbulent non-Newtonian Carboxymethylcellulose (CMC)/copper oxide (CuO) nanofluid in a three-dimensional microtube. Modeling has been done using low- and high-Reynolds turbulent models. CMC/CuO was modeled using power law non-Newtonian model. The authors obtained interesting results, which can be helpful for engineers and researchers that work on cooling of electronic devices such as LED, VLSI circuits and MEMS, as well as similar devices.

Present numerical simulation was performed with finite volume method. For obtaining higher accuracy in the numerical solving procedure, second-order upwind discretization and SIMPLEC algorithm were used. For all Reynolds numbers and volume fractions, a maximum residual of 10⁻⁶ is considered for saving computer memory usage and the time for the numerical solving procedure.

In constant Reynolds number and by decreasing the diameter of nanoparticles, the convection heat transfer coefficient increases. In Reynolds numbers of 2,500, 4,500 and 6,000, using nanoparticles with the diameter of 25 nm compared with 50 nm causes 0.34 per cent enhancement of convection heat transfer coefficient and Nusselt number. Also, in Reynolds number of 2,500, by increasing the concentration of nanoparticles with the diameter of 25 nm from 0.5 to 1 per cent, the average Nusselt number increases by almost 0.1 per cent. Similarly, In Reynolds numbers of 4,500 and 6,000, the average Nusselt number increases by 1.8 per cent.

The numerical simulation was carried out for three nanoparticle diameters of 25, 50 and 100 nm with three Reynolds numbers of 2,500, 4,500 and 6,000. Constant heat flux is on the channel, and the inlet fluid becomes heated and exists from it.

The authors obtained interesting results, which can be helpful for engineers and researchers that work on cooling of electronic devices such as LED, VLSI circuits and MEMS, as well as similar devices.

This manuscript is an original work, has not been published and is not under consideration for publication elsewhere. About the competing interests, the authors declare that they have no competing interests.

This paper aims to study forced convection in a double tube heat exchanger using nanofluids with constant and variable thermophysical properties.

The cold fluid was distilled water flowing in the annulus and the hot fluid was aluminum oxide/water nanofluid which flows in the inner tube. Thermal conductivity and viscosity were taken as variable thermophysical properties, and the results were compared against runs with constant values. Finite volume method was used for solving the governing equations. For distilled water, Re = 500 was used, while for nanofluid, nanoparticles volume fraction equal to 2.5-10 per cent and Re = 100-1,500 were used.

Heat transfer rate can be enhanced by increasing the volume fraction of nanoparticles and Reynolds number. Thermal efficiency is better with constant thermophysical characteristics and the average Nusselt number is better for variable characteristics.

Heat exchanger efficiency is evaluated by using distilled water and nanofluid bulk temperature, thermal efficiency and average and local Nusselt numbers for both variable and constant thermophysical characteristics.

The purpose of this study is three-dimensional flow and heat transfer investigation of water/Al₂O₃ nanofluid inside a microchannel with different cross-sections in two-phase mode.

The effect of microchannel walls geometry (trapezoidal, sinusoidal and stepped microchannels) on flow characteristics and also changing circular cross section to trapezoidal cross section in laminar flow at Reynolds numbers of 50, 100, 300 and 600 were investigated. In this study, two-phase water/Al₂O₃ nanofluid is simulated by the mixture model, and the effect of volume fraction of nanoparticles on performance evaluation criterion (PEC) is studied. The accuracy of obtained results was compared with the experimental and numerical results of other similar papers.

Results show that in flow at lower Reynolds numbers, sinusoidal walls create a pressure drop in pure water flow which improves heat transfer to obtain PEC < 1. However, in sinusoidal and stepped microchannel with higher Reynolds numbers, PEC > 1. Results showed that the stepped microchannel had higher pressure drop, better thermal performance and higher PEC than other microchannels.

Review of previous studies showed that existing papers have not compared and investigated nanofluid in a two-phase mode in inhomogeneous circular, stepped and sinusoidal cross and trapezoidal cross-sections by considering the effect of changing channel shape, which is the aim of the present paper.

Water/Al₂O₃ nanofluid with volume fractions of 0, 0.3 and 0.06 was investigated inside a rectangular microchannel. Jet injection of nanofluid was used to enhance the heat transfer under a homogeneous magnetic field with the strengths of Ha = 0, 20 and 40. Both slip velocity and no-slip boundary conditions were used.

The laminar flow was studied using Reynolds numbers of 1, 10 and 50. The results showed that in creep motion state, the constricted cross section caused by fluid jet is not observable and the rise of axial velocity level is only because of the presence of additional size of the microchannel. By increasing the strength of the magnetic field and because of the rise of the Lorentz force, the motion of fluid layers on each other becomes limited.

Because of the limitation of sudden changes of fluid in jet injection areas, the magnetic force compresses the fluid to the bottom wall, and this behavior limits the vertical velocity gradients. In the absence of a magnetic field and under the influence of the velocity boundary layer, the fluid motion has more variations. In creeping velocities of fluid, the presence or absence of the magnetic field does not have an essential effect on Nusselt number enhancement.

In lower velocities of fluid, the effect of the jet is not significant, and the thermal boundary layer affects the entire temperature field. In this case, for Hartmann numbers of 40 and 0, changing the Nusselt number on the heated wall is similar.

This study aims to numerically investigate the heat transfer and laminar forced and two-phase flow of Water/Cu nanofluid in a rectangular microchannel with oblique ribs with angle of attacks equal to 0-45°. This simulation was conducted in the range of Reynolds numbers of 5-120 in volume fractions of 0, 2 and 4 per cent of solid nanoparticles in three-dimensional space.

This study investigates the effect of the changes of angle of attack of rectangular rib on heat transfer and hydrodynamics of two-phase flow. This study was done in three-dimensional space and simulation was done with finite volume method. SIMPLEC algorithm and second-order discretization of equations were used to increase the accuracy of results. The usage of nanofluid, application of rips with different angles of attacks and using the two-phase mixture method is the distinction of this paper compared with other studies.

The results of this research revealed that the changing angle of attack of ribs is an effective factor in heat transfer enhancement. On the other hand, the existence of rib on the internal surfaces of a microchannel increases friction coefficient. By increasing the volume fraction of nanoparticles, due to the augmentation of fluid density and viscosity, the pressure drop increases significantly. For all of the angle of attacks studied in this paper, the maximum rate of performance evaluation criterion has been obtained in Reynolds number of 30 and the minimum amount of performance evaluation criterion was been obtained in Reynolds numbers of 5 and 120.

Many studies have been done in the field of heat transfer in ribbed microchannel. In this paper, the laminar flow in the ribbed microchannel Water/Cu nanofluid in a rectangular microchannel by using two-phase mixture method is numerically investigated with different volume fractions (0-4 per cent), Reynolds numbers (5-120) and angle of attacks of rectangular rib in the indented microchannel (0-45°).

The purpose of this paper is to numerically simulate the nanofluid boiling inside a tube in turbulent flow regime and to investigate the effect of adding volume faction of CuO nanoparticles on the boiling process.

To make sure the accuracy of the obtained numerical results, the results of this paper have been compared with the experimental results and an acceptable coincidence has been achieved. In the current paper, by Euler–Euler method, the phase change of boiling phenomenon has been modeled. The presented results are the local Nusselt number distribution, temperature distribution of wall, the distribution of volume fraction of vapor phase and fluid temperature at the center of the tube.

The obtained results indicate that using nanofluid is very effective in the postponement of the boiling process. Hence, by change the amount of volume fraction of nanoparticles in base fluid, the location of phase change and bubble creation are changed. Also, at the Reynolds numbers of 50,000, 100,000 and 150,000 with the volume fraction of 2 per cent, the beginning locations of phase change process are, respectively, 2D, 10D and 13D, and for the volume fraction of 4 per cent, the beginning locations of phase change are 4D, 18D and 19D, respectively. These results indicate that, as the volume fraction of nanoparticles increases, the location of the start of the phase change process is postponed that this issue causes the increment of heat transfer from wall to fluid and the reduction of wall temperature. In general, it can be stated that, in boiling flows, using nanofluid because of the delay in boiling phenomenon has a good effect on heat transfer enhancement of heated walls. Also, the obtained results show that, by increasing Reynolds number, the created vapor phase reduces that leads to increase of the Nusselt number.

The paper investigates the effect of using nanofluid in phase change process of cooling fluid.

The purpose of this study is simulation the flow boiling inside a tube in the turbulent flow regime for investigating the effect of using a porous medium in the boiling procedure.

To ensure the accuracy of the obtained numerical results, the presented results have been compared with the experimental results, and proper coincidence has been achieved. In this study, the phase change phenomenon of boiling has been modeled by using the Eulerian–Eulerian multi-phase Rensselaer Polytechnic Institute (RPI) wall boiling model.

The obtained results indicate using a porous medium in boiling process is very effective in a way that by using a porous medium inside the tub, the location of changing the liquid to the vapor and the creation of bubbles, changes. By increasing the thermal conductivity of porous medium, the onset of phase changing postpones, which causes the enhancement of heat transfer from the wall to the fluid. Generally, it can be said that using a porous medium in boiling flows, especially in flow with high Reynolds numbers, has a positive effect on heat transfer enhancement. Also, the obtained results revealed that by increasing Reynolds number, the created vapor phase along the tube decreases and by increasing Reynolds number, the Nusselt number enhances.

In present research, by using the computational fluid dynamics, the effect of using a porous medium in the forced boiling of water flow inside a tube has been investigated. The fluid boiling inside the tube has been simulated by using the multi-phase Eulerian RPI wall boiling model, and the effect of thermal conductivity of a porous medium and the Reynolds number on the flow properties, heat transfer and boiling procedure have been investigated.

This study aims to identify health workforce challenges at Iranian hospitals during the COVID-19 pandemic.

This was a conventional content analysis study conducted in 2020. The population consisted of the managers (heads of hospitals, managers and matrons) and staff (nurses, physicians, etc.) of eligible hospitals. The participants were selected using purposive sampling, and data saturation was achieved after 28 interviews. The data were analyzed in MAXQDA10.

In total, 28 interviews were conducted with 10 women and 18 men. The challenges of hospital human resources were categorized into five main themes and 15 sub-themes. The main themes were the shortage of human resources, burnout, the need to acquire new knowledge and skills, the employees’ health and safety and the reward system.

Identification of challenges faced by human resources is the first step toward preventing human force shortage and psychological problems in the personnel. Implementing the recommendations of the present study would assist the proper management of hospitals’ human resources.

This study aims to build upon resource orchestration theory to theorize and empirically test a model that demonstrates how knowledge assets and innovation ambidexterity trigger a synergy in favor of firm performance.

Drawing on a survey of 158 Iranian knowledge-intensive companies, this study uses the partial least squares based on structural equation modeling to test the research hypotheses.

The results show that two elements of knowledge assets, namely, structural and relational capital, indirectly affect firm performance through the full mediation of innovation ambidexterity. The findings indicate that human capital has no relationship with both innovation ambidexterity and firm performance.

This study offers fresh insights into the issue of how organizations can create value from an effective orchestration of various strategic resources and capabilities, including knowledge assets and innovation ambidexterity.

This study applies resource orchestration theory to concurrently the areas of knowledge resources and organizational ambidexterity to show how innovation ambidexterity plays a role in translating three various knowledge assets into performance.