Search results

The purpose of this paper is to analyze the variation of temperature field, pressure field and deformation of hydrostatic thrust bearing under different working conditions, so as to provide a theoretical basis for improving accuracy and reliability.

In this study, the double rectangular hydrostatic bearing of type Q1-224 was selected as the research object, and the simulation was carried out according to different working conditions, and the obtained data were summarized regularly.

It is found that the overall temperature of hydrostatic bearing increases with the increase of speed and load, and the increase in load will result in a larger pressure distribution which first increases and then decreases with the speed. The deformation trend of the deformation field is found, and it is found that the force deformation is larger than the thermal deformation at low rotational speed, and the thermal deformation is larger than the force deformation at high rotational speed.

In this study, the fluid-structure coupling method of conjugate heat transfer is applied to study the whole hydrostatic bearing. Most of the previous studies only studied the oil film and considered the influence of the convective heat transfer between the hydrostatic bearing and the air in heat transfer, which is rarely seen in the previous research literature.

In this study a numerical analysis of the elastohydrodynamic lubrication point contact problem in the unsteady state of reciprocating motion is presented. The effects of frequency, stroke length and load on film thickness and pressure variation during one operating cycle are discussed. The general tribological behavior of elastohydrodynamic lubrication during reciprocating motion is explained.

The system of equations of Reynolds, film thickness considering surface deformation and load balance equations are solved using the Newton-Raphson technique with the Gauss-Seidel iteration method. Numerical solutions were performed with a sinusoidal contact surface velocity to simulate reciprocating elastohydrodynamics. The methodology is validated using historical experimental measurements/observations and numerical predictions from other researchers.

The numerical results showed that the change in oil film during a stroke is controlled by both wedge and squeeze effects. When the surface velocity is zero at the stroke end, the squeeze effect is most noticeable. As the frequency increases, the general trend of central and minimum film thickness increases. With the same entraining speed but different stroke lengths, the properties of the oil film differ from one another, with an increase in stroke length leading to a reduction in film thickness. Finally, the numerical results showed that the overall film thickness decreases with increasing load.

General tribological behaviors of elastohydrodynamic lubricating point contact, represented by pressure and film thickness variations over time and profiles, are analyzed under reciprocating motion during one working cycle to show the effects of frequency, stroke length and applied load.

This paper aims to investigate the effect of frictional heat on the wear of high-speed rotary lip seals in engines.

In this research paper, the authors focus on the high-speed rotating lip seal of aircraft engines. Using the hybrid lubrication theory, a thermal-fluid-solid coupled numerical simulation model is established to investigate the influence of parameters such as contact pressure distribution, temperature rise and leakage rate on the sealing performance under different operating conditions. By incorporating the Rhee wear theory and combining simulation results with experimental data, a method for predicting the wear of the rotating seal lip profile is proposed. Experimental validation is conducted using a high-speed rotating test rig.

The results indicate that as the speed increases, the rise in frictional heat leads to a decrease in the sealing performance of the lip seal contact region. The experimental results show a similar trend to the numerical simulation results, and considering the effect of frictional heat, the predicted wear of the lip seal profile aligns more closely with the actual wear curve. This highlights the importance of considering the influence of frictional heat in the analysis of rotating seal mechanisms.

This study provides a reference for the prediction of wear profiles of engine high-speed rotary lip seals.

The purpose of this paper is to investigate the performance of an ultra-thin film lubricated conjunction through the elastohydrodynamic lubrication of point contacts for various ridge shapes and sizes located within the contact zone including flat-top, triangle and cosine wave profiles, considering the influence of surface forces of solvation and Van der Waals’ in addition to the hydrodynamic effect to predict an optimum geometric characteristics for surface texture for lubricated conjunctions.

Surface features are simulated in a variety of sizes and shapes including flat-top, triangle and cosine wave profiles. While estimating the elastic deformation of the contacting surfaces, surface forces of solvation and Van der Waals’ are taken into account. The Reynolds equation is solved using the Newton–Raphson method to get the pressure profile and film thickness including the elastic deformation, and surface feature.

The geometrical characteristics of the ridge, its placement in relation to the contact zone and its height all have a significant impact on the performance of ultra-thin film lubricated conjunction. When the triangular-shaped ridge is present in contact, it forecasts even sharper peaks in film thickness and pressure. More friction, wear and eventually contact fatigue are brought on by this more acute pressure and film thickness peaks. The flat-top ridge shape shows a better performance for lubricated conjunction where, the minimum film thickness value is comparable to that obtained for the case of a smooth contact surface. This behavior is attributed to the effect of intermolecular force of solvation. An increase in the size of the ridge results in a step increase in the film thickness for different ridge shapes, particularly for the flat-topped ridge pattern.

Evaluation of the performance of elastohydrodynamic lubricated ultra-thin film conjunction related to film thickness and pressure profile for various ridge surface features of different amplitudes, shapes and sizes located through the contact zone considering the influence of surface forces of solvation and Van der Waals’ in addition to the hydrodynamic effect.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2023-0062/

This paper aims to study the influence of cylindrical texture parameters on the lubrication performance of static and dynamic pressure thrust bearings (hereinafter referred to as thrust bearings) and to optimize their lubrication performance using multiobjective optimization.

The influence of texture parameters on the lubrication performance of thrust bearings was studied based on the modified Reynolds equation. The objective functions are predicted through the BP neural network, and the texture parameters were optimized using the improved multiobjective ant lion algorithm (MOALA).

Compared with smooth surface, the introduction of texture can improve the lubrication properties. Under the optimization of the improved algorithm, when the texture diameter, depth, spacing and number are approximately 0.2 mm, 0.5 mm, 5 mm and 34, respectively, the loading capacity is increased by around 27.7% and the temperature is reduced by around 1.55°C.

This paper studies the effect of texture parameters on the lubrication properties of thrust bearings based on the modified Reynolds equation and performs multiobjective optimization through an improved MOALA.

Tribological research is complex and multidisciplinary, with many parameters to consider. As traditional experimentation is time-consuming and expensive due to the complexity of tribological systems, researchers tend to use quantitative and qualitative analysis to monitor critical parameters and material characterization to explain observed dependencies. In this regard, numerical modeling and simulation offers a cost-effective alternative to physical experimentation but must be validated with limited testing. This paper aims to highlight advances in numerical modeling as they relate to the field of tribology.

This study performed an in-depth literature review for the field of modeling and simulation as it relates to tribology. The authors initially looked at the application of foundational studies (e.g. Stribeck) to understand the gaps in the current knowledge set. The authors then evaluated a number of modern developments related to contact mechanics, surface roughness, tribofilm formation and fluid-film layers. In particular, it looked at key fields driving tribology models including nanoparticle research and prosthetics. The study then sought out to understand the future trends in this research field.

The field of tribology, numerical modeling has shown to be a powerful tool, which is both time- and cost-effective when compared to standard bench testing. The characterization of tribological systems of interest fundamentally stems from the lubrication regimes designated in the Stribeck curve. The prediction of tribofilm formation, film thickness variation, fluid properties, asperity contact and surface deformation as well as the continuously changing interactions between such parameters is an essential challenge for proper modeling.

This paper highlights the major numerical modeling achievements in various disciplines and discusses their efficacy, assumptions and limitations in tribology research.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2023-0076/

This study aims to present a numerical solution for the analysis of the influence of surface roughness as presented by a sinusoidal ripple of different amplitude and wavelength on the performance of transient elastohydrodynamic lubrication at motion start-up under different operational parameters of entraining speed and load as well as different acceleration rates.

A statistical asperity micro-contact model represented by a sinusoidal ripple expressed by two parameters (wavelength and undeformed amplitude) is considered. The ball equation of motion is used to calculate the force on the ball as it starts to move. The time-dependent Reynolds equation is solved together with surface deformation and statistical asperity models using the Newton–Raphson technique with the Gauss–Seidel iteration method.

The behaviour of the film thickness was found to be strongly influenced by the acceleration rate for different ripple amplitude and wavelength parameters. The effect of increasing the final entraining speed will eventually lead to rapid film thickness build-up and increase the film thickness jump at the moment of motion start-up. The effect of increasing applied load is to reduce the deviation of the minimum film thickness jump at the start-up of motion, making its value approximately equal to the steady-state value over the entire run-time period.

Influence of surface roughness for various wavelength and undeformed amplitude on the performance of transient elastohydrodynamic lubrication at motion start-up is presented at different acceleration rates as well as for different operating parameters of entraining speed and load. Ball equation of motion is used to calculate the force on the ball as it starts to move.

The aim of this study is to experimentally analyze the friction and wear responses of different steels to different surface films generated in oil-lubricated tribological contacts.

Tribological experiments were conducted using a 100Cr6 bearing ball sliding against a V155 carbon steel disk and 316L stainless steel disk, respectively. Lubricants with additives known to form zinc dialkyl-dithiophosphate (ZDDP) or Ca tribofilms were used.

Both of the ZDDP and Ca tribofilms helped stabilize the friction coefficient of the carbon steel and stainless steel. The ZDDP tribofilm could effectively protect the carbon steel from wear, in contrast to the stainless steel, whereas the wear of both carbon steel and stainless steel could be significantly reduced by the Ca tribofilm. In the case of neither ZDDP nor Ca tribofilms formation, the 100Cr6 ball was worn by the V155 disk and generated a special surface topography. A polishing wear mechanism was proposed to explain the wear of the 100Cr6 ball.

This study clearly shows the different friction and wear responses of steels to the different surface films and the response is dependent on the tested steel.

The present paper aims to analyse the synergistic effect of pocket orientation and piezo-viscous-polar (PVP) lubrication on the performance of multi-recessed hybrid journal bearing (MHJB) system.

To simulate the behaviour of PVP lubricant in clearance space of the MHJB system, the modified form of Reynolds equation is numerically solved by using finite element method. Galerkin’s method is used to obtain the weak form of the governing equation. The system equation is solved by Gauss–Seidal iterative method to compute the unknown values of nodal oil film pressure. Subsequently, performance characteristics of bearing system are computed.

The simulated results reveal that the location of pressurised lubricant inlets significantly affects the oil film pressure distribution and may cause a significant effect on the characteristics of bearing system. Further, the use of PVP lubricant may significantly enhances the performance of the bearing system, namely.

The present work examines the influence of pocket orientation with respect to loading direction on the characteristics of PVP fluid lubricated MHJB system and provides vital information regarding the design of journal bearing system.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0241/

Due to high speeds, heavy loads, large slide-to-roll ratios (SRR) and other variable operating conditions, some rolling bearings that have been working in harsh conditions may experience flash temperatures in the contact area, which may result in early damage like smearing and then affect service life. This study aims to investigate the flash temperature phenomenon of rolling bearings through theoretical and experimental analysis.

A technology for measuring temperature distribution in rolling ball on disk contact under lubrication was developed. The test-rig can simulate the ball bearing contact. The effects of working conditions such as entrainment speed, load, SRR and lubricating oil viscosity on the flash temperature were investigated.

The results of the theoretical calculation and experiments indicate that the parameters promoting the reduction of film thickness in elastohydrodynamic lubrication are always related with the number of flash points, even film thickness reduced to mixed lubrication. The flash temperature is easier to happen in conditions of high SRR, heavy load, slow entrainment speed and low viscosity oil.

This work conducts an experimental study on the flash temperature phenomenon, providing a test technology for bearing lubrication and failure investigation.

This author has opted into Transparent Peer Review available at: https://publons.com/publon/10.1108/ILT-04-2023-0104