Search results

Porosity is one of the most important properties of the textile substrate. It can influence the comfort of a garment by affecting its breathability and thermal conductivity. During the process of dyeing, the dye liquor comes in contact with the substrate; the absorption of the dye liquor into the substrate will be dependent on its porosity. The concept of porosity between the yarns of fabric is a common phenomenon; however, the porosity between the fibres in the yarn can also influence the dyeing behaviour of the fabric.

In this research, ring and rotor yarns of 25/s and 30/s counts are considered as textile substrates. The porosity of yarns was determined theoretically and experimentally using the image analysis method.

It was found that theoretical porosity is independent of the yarn manufacturing method. In addition, 30/s yarn was more porous as compared with 25/s yarn having a higher pore area. Rotor yarns had higher porosity, dye fixation and K/S as compared with ring yarns. Dyeing behaviour was also dependent on the count of yarn. Specifically, 30/s yarns have higher dye fixation as compared with 25/s yarns. However, 25/s yarns were dyed with deeper shades showing higher K/S values. Also, 25/s yarns are coarser than 30/s yarns having higher diameters and cross-sectional area, thus resulting in deeper shades and higher K/S values.

This novel technique is based on the comparative study of the porosity of various types of yarns using the image analysis technique. This investigation shows that the porosity between the fibres in the yarn can also influence the dyeing behaviour of the yarn.

In experiments utilising sweat solution and distilled water, seamed ensembles performed less thermally efficiently than unseamed fabrics.

Water may not accurately reflect perspiration when testing multi-layered clothes for thermal comfort in wet state. Most researchers used water or sodium chloride (NaCl) to measure wet state thermal comfort. However, human perspiration is an extremely complex mixture of aqueous chemicals, including minerals, salts, lipids, urea and lactic acid. This study compares the effects of simulated sweat solution to distilled water on the thermal behaviour of a multi-layered fabric assembly with different seam patterns.

Experiment results show that stitching decreases thermal resistance and thermal conductivity. Seam pattern of 10 cm diagonal spacing is more thermally resistant than 2.5 cm diagonal spacing. In comparison to that of simulated sweat, fabric that has been moistened with distilled water exhibits increased thermal conductivity. Hollow polyester wadding or micro polyester wadding as the intermediate layer exhibits greater thermal resistance than multi-layered construction with spacer fabric as middle layer.

This study considers human perspiration while designing protective clothing for wet thermal comfort.

Dehydrated bacterial cellulose’s (BC) intrinsic rigidity constrains applicability across textiles, leather, health care and other sectors. This study aims to yield a novel BC modification method using glycerol and succinic acid with catalyst and heat, applied via an industrially scalable padding method to tackle BC’s stiffness drawbacks and enhance BC properties.

Fabric-like BC is generated via mechanical dehydration and then finished by using padding method with glycerol, succinic acid, catalyst and heat. Comprehensive material characterizations, including international testing standards for stiffness, bending properties (cantilever method), tensile properties, moisture vapor transmission rate, moisture content and regain, washing, thermal gravimetric analysis, derivative thermogravimetry, Fourier-transform infrared spectroscopy and colorimetric measurement, are used.

The combination of BC/glycerol/succinic acid dramatically enhanced porous structure, elongation (27.40 ± 6.39%), flexibility (flexural rigidity of 21.46 ± 4.01 µN m; bending modulus of 97.45 ± 18.20 MPa) and moisture management (moisture vapor transmission rate of 961.07 ± 86.16 g/m²/24 h; moisture content of 27.43 ± 2.50%; and moisture regain of 37.94 ± 4.73%). This softening process modified the thermal stability of BC. Besides, this study alleviated the drawbacks for washing (five cycles) of BC and glycerol caused by the ineffective affinity between glycerol and cellulose by adding succinic acid with catalyst and heat.

The study yields an effective padding process for BC softening and a unique modified BC to contribute added value to textile and leather industries as a sustainable alternative to existing materials and a premise for future research on BC functionalization by using doable technologies in mass production as padding.

Kapok was well-known for its oleophilic properties, but its mechanical properties and morphology impeded it from forming suitable absorbent materials. This study aims to demonstrate the process of creating an oil-absorbent web from a blend of treated kapok and polypropylene fibers.

Kapok fibers were separated from dried fruits, then the wax was removed with an HCl solution at different concentrations. The morphological and structural changes of these fibers were investigated using scanning electron microscopy images. The blending ratios of kapok and polypropylene fibers were 60/40, 70/30 and 80/20, respectively. The fiber blends were fed to a laboratory carding machine to form a web and then consolidated using the heat press technique. The absorption behavior of the formed web was evaluated regarding oil absorption capacity and oil retention capacity according to ASTM 726.

The results showed that the HCl concentration of 1.0% (wt%) gave the highest wax removal efficiency without damaging the kapok fibers. This study found that oil absorbency is influenced by the fiber blending ratio, web tensile strength and elongation, porosity, oil type and environmental conditions. The oil-absorbency of the web can be re-used for at least 20 cycles.

This study only looked at three types of oils: diesel, kerosene and vegetable oils.

When the problem of oil spills in rivers and seas is growing and causing serious environmental and economic consequences, using physical methods to recover oil spills is the most effective solution.

This research adds to the possibility of using kapok fiber in the form of a web of non-woven fabric for practical purposes.

The aim of this study is to optimize the electrospinning parameters used in the production process of polyvinyl chloride (PVC) nanofibers.

The response surface methodology (RSM) was used to determine the experimental design. The 30 nanofiber prototypes candidates were electrospun using a needle-based electrospinning machine. PVC polymer, N-dimethyl formamide and tetrahydrofuran solvents were used to prepare the electrospinning solution.

The electrospun nanofibers had a mean diameter of 386 ± 136.57 nm, in the range of 200−412 nm. The mean porosity was 31.60 ± 6.37% in the range of 15.33−41.53%. The webs made from electrospun nanofibers had a mean pressure loss of 194.23 ± 47.7 pa in the range of 124−300 pa. The highest statistically significant correlation was observed between solution concentration and nanofiber diameter (r = 0.756, p < 0.05).

The optimal electrospinning parameters were determined to be: a solution concentration of 11 weight percent, a voltage of 16.5 kV, a needle-collector distance of 13.5 cm and an electrospinning duration of 4 h.

Stainless-steel electromagnetic shielding (EMS) fabrics are widely applied as protective materials against electromagnetic interference (EMI). However, these fabrics primarily shield electromagnetic waves through reflection, which can lead to the formation of resonance effects that severely compromise their protective capabilities and potentially cause secondary electromagnetic pollution in the external environment.

In this paper, carbon nanotube fibers are added via spacing method to replace some stainless-steel fibers to impart absorbing properties to stainless-steel EMS fabric. The shielding effectiveness (SE) of the EMS fabrics across various polarization directions is analyzed. Additionally, a spacing arrangement for the carbon nanotube fibers is designed. The EMS fabric with carbon nanotube fibers is manufactured using a semi-automatic sample loom, and its SE is tested using a small window method test box in both vertical and horizontal polarization directions.

According to the experimental data and electromagnetic theory analysis, it is determined that when the spacing between the carbon nanotube fibers is less than a specific distance, the SE of the stainless-steel EMS fabric significantly improves. The fabric exhibits stable absorbing properties within the tested frequency range, effectively addressing the issue of secondary damage that arises from relying solely on reflective shielding. Conversely, as the spacing between the carbon nanotube fibers exceeds this distance, the SE diminishes. Notably, the SE in the vertical polarization direction is substantially higher than that in the horizontal polarization direction at the same frequency.

This study provides a new path for the development of high-performance EMS fabrics with good wave-absorption characteristics and SE.

This study aims to characterize the properties of natural cellulose fiber from the pseudo-stems of the curcuma zedoaria plant.

The fiber was extracted using the biological retting process (cold-water retting). The intrinsic fiber properties obtained were used to evaluate the possibility of using fiber for textile applications.

The average length of a curcuma zedoaria fiber was 34.77 cm with a fineness value of 6.72 Tex. A bundle of curcuma zedoaria fibers was comprised of many elementary fibers. Curcuma zedoaria had an irregular cross-section, with the lumen having a varied oval shape. Curcuma zedoaria fibers had tenacity and elongation value of 3.32 gf/denier and 6.95%, respectively. Curcuma zedoaria fibers had a coefficient of friction value of 0.46. Curcuma zedoaria fibers belong to a hygroscopic fiber type with a moisture regain value of 10.29%.

Extraction and Characterization of Curcuma zedoaria Pseudo-stems Fibers for Textile Application.

The purpose of this paper is to gain an in-depth understanding into the research progress, hot spots and future trends in smart gripping technology in the field of apparel smart manufacturing.

This work scrutinised the current research status of the five automatic grasping methods for garment fabrics including the pneumatic suction grasping, the electrostatic grasping, the intrusive grasping and the dexterous grasping. Specifically, the principles, characteristics, main devices and the impact on garment production were discussed.

In particular, soft finger of the dexterous grasping method has good flexibility and adaptability in the process of fabric grasping, which provides a new solution for garment production automation. Up to now, the reviewed method in general exhibit good grasping speed, high grasping stability and flat grasping process. However, in the face of complex fabric materials which are thin and flexible and do not return their original shapes when deformed in practical applications, the gripper for automatic fabric grasping need new technological breakthroughs in the positioning accuracy, grab efficiency and flexible grasping.

The outcomes offered an overview of the research status and future trends of the automatic grasping methods for garment fabrics in the field of apparel intelligent manufacturing. It could not only provide scholars with convenience in identifying research hot spots and building potential cooperation in the follow-up research but also assist beginners in searching core scholars and literature of great significance.

Perspiration and heat are produced by the body and must be eliminated to maintain a stable body temperature. Sweat, heat and air must pass through the fabric to be comfortable. The cloth absorbs sweat and then releases it, allowing the body to chill down. By capillary action, moisture is driven away from fabric pores or sucked out of yarns. Convectional air movement improves sweat drainage, which may aid in body temperature reduction. Clothing reduces the skin's ability to transport heat and moisture to the outside. Excessive moisture makes clothing stick to the skin, whereas excessive heat induces heat stress, making the user uncomfortable. Wet heat loss is significantly more difficult to understand than dry heat loss. The purpose of this study is to provided a good compilation of complete information on wet thermal comfort of textile and technological elements to be consider while constructing protective apparel.

This paper aims to critically review studies on the thermal comfort of textiles in wet conditions and assess the results to guide future research.

Several recent studies focused on wet textiles' impact on comfort. Moisture reduces the fabric's thermal insulation value while also altering its moisture characteristics. Moisture and heat conductivity were linked. Sweat and other factors impact fabric comfort. So, while evaluating a fabric's comfort, consider both external and inside moisture.

The systematic literature review in this research focuses on wet thermal comfort and technological elements to consider while constructing protective apparel.