Search results

The purpose of this paper is to study the colour stability and water content resistivity of the green colour coating paint film (consisting of chlorophyll) during exposure to ultraviolet A (UV-A).

The natural green dye was prepared by immersing Cassia alata L. leaves in absolute ethanol. The extract was prepared in two batches of dye samples where one of it was a pure dye and the other was added with 3 Wt. % Cu(NO₃)₂ as an additive. Polymer blend as a binder was prepared by mixing poly(methyl methacrylate) (PMMA) and commercial acrylic polyol. The blended polymer was mixed with the natural dye in a specific ratio and applied as coating paint film on glass panel surfaces. The visible spectrum stability (colour stability) and water content resistivity of the coating paint films during exposure to UV-A were monitored.

Addition of Cu(NO₃)₂ had improved the colour stability of the coating paint film. Fourier transform infrared spectroscopy analysis showed that both coating paint films do not absorb water and are resistive to water content.

The ability of Cu(NO₃)₂ as an colour stability additive to the natural green dye applied in the coating paint film.

The coating paint film developed in this work is suitable to be applied on glass substrates.

The colour stability of the coating paint film was analysed by using the reflectance spectrum.

This paper aims to study the colour stability of chlorophyll and the effect of copper (II) nitrate – Cu(NO₃)₂ – as an additive in natural dye coating films after being exposed to ultraviolet-A (UV-A).

The natural dye was extracted from the leaves of Cassia alata L. using absolute ethanol as the solvent. The extract was divided into two parts and, one of it was added with 3 wt.% Cu(NO₃)₂ as an additive. The polymer blend of poly(methyl methacrylate) (PMMA) and acrylic polyol was used as the coating binder. Both parts of the dye with and without additive were mixed with the blended polymer in a specific ratio. The resulted mixtures were applied as coating films on glass substrates. The colour stability of the coating films on exposure to UV-A with the time of exposure was observed with Commission internationale de l’éclairage (CIE) L*a*b* colour coordinates. The hidden power by the means of reflectivity and glossiness of the coatings was also studied. Statistical standard deviation (STD) was used to analyse the data.

The test showed that the coating films containing Cu(NO₃)₂ had smaller colour differences, (ΔE*) indicating higher colour stability. The analysis on hidden power also showed that the coating film with Cu(NO₃)₂ was 1.6 times more stable than the film without additive. All the measurements in this study were observed within 35 days of duration.

This paper implies the potential of using natural dye extracted from Cassia alata L. leaves as a stable dye colourant for coating applications.

The coating film developed in this study is suitable for glass substrate applications.

A new method of preparing solvent-based coating film from PMMA–acrylic polyol with chlorophyll colourant is introduced in this study.

This paper aims to discuss about the benefits of Cu(NO₃)₂ applied in coating paint film that consists of plant extract from Cassia Alata. Cu(NO₃)₂ has been added to the coating paint film as a colour stabilizer and as an antifungal property by forming a zone of inhibition towards fungal growth.

The coating paint film resin consists of a mixture of poly (methyl methacrylate) (PMMA) and acrylic polyol. The coating paint film’s performances were observed in terms of visible optical and physical appearance.

When exposed to the fungus Trichoderma Sp., a zone of inhibition of 208 mm² was formed around the coating paint film and therefore it gave the coating paint films an antifungal property. The commission internationale de l’éclairage (CIE) L*a*b* colour coordinate system was used to identify the colour changes in the coating paint film and it was found that the addition of Cu(NO₃)₂ to the coating paint film has a better colour stability, as it has a lower standard deviation (STD) value of 6.46 than the pure dye coating paint film of 8.95. The gloss of coating paint film with the addition of Cu(NO₃)₂ was found to be have a more stable gloss based on its smaller STD value at both angles taken at 20° and 60°.

The Cassia Alata plant has different amount of antifungal properties based on location its growth.

The coating paint film developed in this study is suitable for indoor applications.

The plant extract from the Cassia Alata gives the coating paint film an antifungal property.

This paper aims to focus on a comparison study of the visible stability of natural blue dye consisting anthocyanin molecules extracted from Clitoria ternatea in coating films.

The coating films were prepared by mixing the blue dye with poly(acrylamide-co-acrylic acid) in three different weight ratios. Samples were coded as 10PBA, 15PBA and 20PBA, where PBA is the abbreviation for poly acrylamide-co-acrylic acid, blue dyes and anthocyanin. The number at the beginning of each code represents the weight percentage of poly(acrylamide-co-acrylic acid) to natural blue dye. The mixtures were applied on separate glass substrates to form coating films. Another set of samples were prepared for the comparison study with a commercial acrylic clear coat (cc) applied on the surface of the 10PBA, 15PBA and 20PBA coating films. These coating films were coded 10PBAcc, 15PBAcc and 20PBAcc. The purpose of the clear coat is to observe how it affects the colour stability of the blue coating films with respect to time. All samples were exposed to the ultraviolet (UV) source, an 18 W Philips TL-D 18w/830 UV fluorescent lamp. The UV lamp was placed 15 cm above the surface of the samples for 35 days. The colour of the coatings was measured using CIE L*a*b* colour space coordinate.

The results obtained show 10PBA and 10PBAcc have the highest colour stability after 35 days of exposure to UV light. The reflectivity of the coating films was also measured during exposure to UV lamp. Reflectivity measurements also showed that 10PBA and 10PBAcc coating films had the highest reflective stabilities.

The potential of using natural blue dye consisting anthocyanin in coating film to obtain high colour stability.

The coating film developed in this work is suitable to be applied on glass substrates.

The application of anthocyanin dye extracted from the Clitoria ternatea L. as a colourant in coating films

The purpose of this work is to investigate the correlation characteristics in mechanical, thermal and optical properties of PMMA‐acrylic polyol polymer blends mixed with lawsone natural dye for coating paint application.

Natural brownish dye colorant was extracted from Lawsonia Inermis leaves used as a dye colorant in this paint coating system by using ethanol as the solvent. Poly(methyl methacrylate) (PMMA), blended with acrylic polyol was used as the binder system. The ratio of PMMA to acrylic polyol was varied with PMMA dominance. The dye colorant was fixed at 10 wt percent.

The potential time measurement tests showed that the dye colorant paint system with 10 wt percent of acrylic polyol has the highest coating resistance against electrolyte penetration. The dye colorant paint system with 30 wt percent acrylic polyol performed better in mechanical tests such as cross‐hatch and impact resistance. The dye colorant paint system molecular crosslinks were analysed by using the fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction spectroscopy.

The ratio of lawsone dye colorant in the polymer blends is found limited to 10 percent. Increasing in the percentage of lawsone dye colorant will cause inhomogeneity in coating paint sample.

A new formulation of natural dye colorant paint system with 10 percent wt dye volume concentration of lawsone as pigment was obtained.

The purpose of this paper is to observe the thermal and colour stabilities of coating films consisting of natural dye anthocyanin colourant with acid and nitrate salt as additives.

The natural dye was extracted from Hibiscus sabdariffa L. (Roselle) by using distilled water as solvent. The extracted dye was mixed with 1 weight per cent hydrochloric acid and 5 weight per cent calcium nitrate to conduct the comparison study. The dye samples were than mixed with poly (vinyl alcohol) (PVA). The mixtures were applied on glass panels to form coating films. The coating films were left to dry for 24 hours. The thermal stability of coating films was investigated by using thermogravimetric analysis (TGA). The amorphousness coating films molecular structures were observed by using x-ray diffraction (XRD). CIE L*a*b* colour coordinate space technique was used to investigate the coating films colour stability against ultraviolet (UV).

The results show that addition of hydrochloric acid (HCl acid) enhanced thermal stability of PVA-anthocyanin coating and shifted the degradation temperature to higher temperature at 300°C. HCl acid also improved UV stability of the coating system significantly with the reduced ΔE from 26.67 to 16.89. Addition of calcium nitrate (Ca(NO₃)₂) salt promotes good interaction with PVA-anthocyanin system that caused structural changes, improved thermal stability and increased T_g from 61.5 to 83.1°C.

The potential of using natural dye extracted from plant as renewable material.

The coating films developed in this works are suitable for glass substrate application.

Development of water-based coating from PVA binder with anthocyanin colourant is introduced in this study.

The purpose of this work is to investigate the influence of curcumin dye natural colorant on adhesion, mechanical, thermal and electrochemical properties of blend poly (methyl methacrylate) (PMMA) – acrylic polyol.

Extracted curcumin yellow dye colorant from Curcuma Demostica was mixed with PMMA‐acrylic polyol blended polymer in the volume ratios of 9:1, 8:2 and 7:3. The mixtures were applied on pre‐treated cold‐roll mild steel panels. All of the paint coating samples were subjected to potential time measurement (PTM), rapid impact deformation, differential scanning calorimetry (DSC), cross hatch and Fourier transform infrared spectroscopy (FTIR) tests.

The addition of curcumin dye colorant was able to improve the adhesion, flexibilities and resistance against electrolytes penetration of the blended poly (methyl methacrylate) (PMMA) – acrylic polyol polymer paint system. Cross hatch test studies showed that high amount of curcumin dye colorant (AP30 paint system) had the lowest peel‐off coating area from the substrate. The FTIR test had confirmed the high concentration of hydroxyl group in the AP30 sample. The hydroxyl group was able to promote hydrogen bonding between coating substrate interface. The AP30 sample had the highest coating flexibilities when tested with rapid impact test. This was due to the lowest glass transition value T_g which indicated lowest cross linking density in the coating molecules structure. In the PTM test, AP30 paint system had shown the highest rate electrolytes penetration within the AP sample.

The composition of curcumin dye colorant in the polymer blend is limited from 10 percent to 30 percent pigment volume concentration. Increasing the amount of lawsone pigment will result inhomogeneous mixtures.

The AP paint system is suitable for interior applications. This paint system has to be mixed with suitable additive materials to improve its performance for exterior purpose.

The purpose of this paper is to observe the colour and thermal stability of natural red dye consisting of anthocyanin with addition of different aqueous acids and applied as coating films.

The natural red dye was extracted from Hibiscus sabdariffa L. (roselle) flowers and mixed with 1 per cent hydrochloric acid, 5 per cent acetic acid, 5 per cent citric acid and 5 per cent oxalic acid. All the dye samples were exposed to heat and UV-B to observe the colour stability by calculating the half-life and rate of reaction. In coating film application, each of the dye samples was mixed with 25 wt% of poly(vinyl alcohol) (PVA) and applied on to a glass substrate. The coating samples’ colour stability was observed by using CIE L*a*b* colour space coordinates. The coating films’ weight loss stability against temperature was observed by using thermogravimetric analysis.

Addition of hydrochloric acid enhances the thermal and UV stability of the anthocyanin natural dye. This can be observed from the calculation of the half-life of the dye. The half-life values for the thermal and UV stability studies were 1,155 hours and 210 hours, respectively. In coating films, the sample with addition of acetic acid showed the highest colour stability with colour difference (ΔE*) value 8.95.

The coating films developed in this work are not suitable to be applied on metal substrates due to the presence of water, which can contribute to the corrosion formation.

The coating films developed in this work are suitable for washable coating application. In other words, they are non-permanent coatings applied on a glass substrate.

Development of water-based coatings from PVA binder with anthocyanin colourant is introduced in this study.

Examines the tenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

Examines the fourteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.