Search results

Wearable electronic devices have emerged which require compact, flexible power storage devices such as batteries and supercapacitors. Recently, energy storage devices have been developed based on supercapacitor threads. However, current supercapacitor energy storage threads which use electrolytes based on aqueous gels have a 1 V potential window. This is much lower than the voltage required by most electronic devices. This current contribution presents an approach for fabricating a multilayer supercapacitor working as a circuit unit, in which series combinations of the multiple layer structures can achieve a higher potential window, which can better meet the needs of wearable electronic devices.

Two-capacitive layer thread supercapacitors were fabricated using a semi-automatic dip coating method by coating two capacitive layers sequentially on a 50 μm stainless steel core wire, each capacitive layer includes ink, aqueous-based gel electrolyte and silver conductive paint layers.

Two capacitive layers of the single thread supercapacitor can work independently, or as combination circuits – parallel and series. Cyclic voltammograms showed that all flexible circuits have high electrochemical stability. For the case of series circuit configuration, with H₃PO-polyvinyl alcohol (PVA) gel electrolyte, a working potential window of 2 V was achieved.

A flexible single thread supercapacitor of multilayer structure, with working voltage above 1 V in H₃PO₄-PVA gel electrolyte, has not been reported before. A semi-automatic dip coating setup used to process the thread supercapacitor has high potential for transfer to an industrial environment for mass production.

The purpose of this work was fabrication of a small energy harvester.

The multilayer thermoelectric power generator based on thick-film and low temperature co-fired ceramic (LTCC) technology was fabricated. Precise paths printing method was used to fabricate Ag/Ni and Ag/PdAg thermocouples on a number of unfired LTCC tapes. The tapes were put together to form a multilayer stack. The via holes were used to make the electrical connections between adjacent layers. Finally, the multilayer stack was fired in the appropriate thermal profile.

It consists of 450 thermocouples and generates output voltage of about 0.45 V and output electrical power of about 0.13 mW when a temperature difference along the structure is 135°C. In the paper, individual stages of energy harvester fabrication process as well as its output parameters are presented.

Miniaturized thermoelectric energy harvester based on thick-film and LTCC technology was fabricated. As materials, metal-based pastes were used. This is the first paper where multilayer thermoelectric harvester, fabricated with the aid of LTCC technology, was described.

This paper aims to propose an approach based upon the principal component analysis (PCA) to define a contribution rate for each variable and then select the main variables as inputs to a neural network for energy load forecasting in the region southeastern Brazil.

The proposed approach defines a contribution rate of each variable as a weighted sum of the inner product between the variable and each principal component. So, the contribution rate is used for selecting the most important features of 27 variables and 6,815 electricity data for a multilayer perceptron network backpropagation prediction model. Several tests, starting from the most significant variable as input, and adding the next most significant variable and so on, are accomplished to predict energy load (GWh). The Kaiser–Meyer–Olkin and Bartlett sphericity tests were used to verify the overall consistency of the data for factor analysis.

Although energy load forecasting is an area for which databases with tens or hundreds of variables are available, the approach could select only six variables that contribute more than 85% for the model. While the contribution rates of the variables of the plants, plus energy exchange added, have only 14.14% of contribution, the variable the stored energy has a contribution rate of 26.31% being fundamental for the prediction accuracy.

Besides improving the forecasting accuracy and providing a faster predictor, the proposed PCA-based approach for calculating the contribution rate of input variables providing a better understanding of the underlying process that generated the data, which is fundamental to the Brazilian reality due to the accentuated climatic and economic variations.

Inspired by the development of eco-friendly flexible electronics, this paper aims to present a series of paper-based electronics drawn by pencils, which can be used as favorable sensing elements in daily life.

Pencil traces are deposited on the porous surface of Xerox paper by the mechanical exfoliation during writing process, which can be used as basic components to construct functional electronics for daily sensing applications. By changing pencil grade, the obtained traces can work as conductive wires, electrodes, resistors and piezoresistive gauges.

The experimental results confirm their practical applications in sensing several daily activities, including finger motion, touching and the temperature of water in paper cup. Moreover, the used electronics can be easily handled and recycled.

The shortage in functionality, reliability and performance consistency induced by manual operation is an evident challenge, which makes the pencil-on-paper devices more suitable to work as a temporary solution to satisfying the demands from emergency circumstances.

The pencil-on-paper devices, motivated by the electroconductibility and piezoresistivity of pencil trace, can be explored as sensing prototypes in detecting daily activities. Meantime, their advances in easy accessibility, rapid fabrication, low cost and eco-fitness endow them excellent capacity of meeting the “on-site, real-time” demands.

In addition to agriculture, energy production, and industries, potable water plays a significant role in many fields, further increasing the demand for potable water. Purification and desalination play a major role in meeting the need for clean drinking water. Clean water is necessary in different areas, such as agriculture, industry, food industries, energy generation and in everyday chores.

The authors have used the different search engines like Google Scholar, Web of Science, Scopus and PubMed to find the relevant articles and prepared this mini review.

The various stages of water purification include coagulation and flocculation, coagulation, sedimentation and disinfection, which have been discussed in this mini review. Using nanotechnology in wastewater purification plants can minimize the cost of wastewater treatment plants by combining several conventional procedures into a single package.

In society, we need to avail clean water to meet our everyday, industrial and agricultural needs. Purification of grey water can meet the clean water scarcity and make the environment sustainable.

This mini review will encourage the researchers to find out ways in water remediation to meet the need of pure water in our planet and maintain sustainability.

The dispersity of graphene oxide (GO) has an important effect on the properties of epoxy resin (EP) composites. Many modification and dispersion methods require the use of inert solvents which do not participate in the modification reaction, although GO can be uniformly dispersed in water and alcohol solvents. Based on this requirement, several inert solvents were selected as dispersion solvents to find out the suitable inert solvent for GO dispersion into EP matrix.

Several inert solvents with different solubility parameters were selected as dispersion solvents to prepare GO/EP composite. The microstructure, mechanical properties, insulation properties, dielectric properties and thermal property of the composite were characterized, which was due to find suitable inert solvent for GO dispersion into EP matrix.

The dispersity of N, N-dimethylformamide (DMF) was the best stable suspension state when it was used as solvent instead of occurring sedimentation and agglomeration. Moreover, DMF was further confirmed as a suitable inert solvent for the dispersion of GO into EP according to the mechanical properties, insulation properties and thermal conductivity characterization.

The dispersion of GO in solvents has already been researched, but the traditional solvents, such as alcohols and water, has shown their limitations with the increase of modification methods, which were not suitable for the modification environment such as cyanate graft modification. Therefore, it was very important to choose a kind of inert solvent for dissolving EP matrix and dispersing GO better.

Several inert solvents were used to disperse GO into EP, and the influence of different dispersing solvents on the adhesive was discussed through the analysis of the mechanical properties, insulation properties and thermal conductivity, which was due to explore the inert solvent suitable for GO dispersion.

The novel structures and properties of nanostructure and nanomaterials give people perfect artistic expression of feeling and sense, then the nanoart discipline is developed and is closely related on the nanotechniques. The many achieved novel nanostructures with strong anti-corrosion prepared by the anodization have been reviewed. The paper would raise public awareness of nanotechnology, nanomaterial and their impact on our lives.

Anodization is a very effective and simple technique to form various nanostructures of metal oxide. It includes hard anodization, mild anodization and pulse anodization. Many measures have been introduced anodization process to improve the quality of formed nanostructure and enhance its properties, such as anti-corrosion.

The formation mechanism of anodic aluminum oxide (AAO) by using the mild, hard and pulse anodization has been discussed. The pretexture process and many other measures have been taken in mild and hard anodization to improve the regularity of pore array and greatly accelerate the formation rate of AAO. The pulse anodization has been used to prepare the multilayer Y-branched AAO film, which exhibits steady rich and vivid structure colors and gives a very good artistic expression. Furthermore, many other metal oxide nanostructures such as TiO₂ and CuO have also been fabricated using the anodization techniques.

Various nanostructures of metal oxide prepared by anodization have been reviewed and are itself a perfect artwork in mesoscale. Also, many nanostructures have exhibited steady, rich and vivid structure colors and give people a very good artistic expression.

This review paper aims to introduce the inkjet printing as a tool for fabrication of flexible/wearable sensors. It summarizes inkjet printing techniques including various modes of operation, commonly used substrates and inks, commercially available inkjet printers and variables affecting the printing process. More focus is on the drop-on-demand printing mode, a strongly considered printing technique for patterning conductive lines on flexible and stretchable substrates. As inkjet-printed patterns are influenced by various variables related to its conductivity, resistivity, durability and dimensions of printed patterns, the main printing parameters (e.g. printing multilayers, inks sintering, surface treatment, cartridge specifications and printing process parameters) are reported. The embedded approaches of adding electronic components (e.g. surface-mounted and optoelectronic devices) to the stretchable circuit are also included.

In this paper, inkjet printing techniques for fabrication of flexible/stretchable circuits will be reviewed. Specifically, the various modes of operation, commonly used substrates and inks and variables affecting the printing process will be presented. Next, examples of inkjet-printed electronic devices will be demonstrated. These devices will be compared to their rigid counterpart in terms of ease of implementation and electrical behavior for wearable sensor applications. Finally, a summary of key findings and future research opportunities will be presented.

In conclusion, it is evident that the technology of inkjet printing is becoming a competitor to traditional lithography fabrication techniques, as it has the advantage of being low cost and less complex. In particular, this technique has demonstrated great capabilities in the area of flexible/stretchable electronics and sensors. Various inkjet printing methods have been presented with emphasis on their principle of operation and their commercial availability. In addition, the components of a general inkjet printing process have been discussed in details. Several factors affect the resulting printed patterns in terms of conductivity, resistivity, durability and geometry.

The paper focuses on flexible/stretchable optoelectronic devices which could be implemented in stretchable circuits. Furthermore, the importance and challenges related to printing highly conductive and highly stretchable lines, as well as reliable electronic devices, and interfacing them with external circuitry for power transmission, data acquisition and signal conditioning have been highlighted and discussed. Although several fabrication techniques have been recently developed to allow patterning conductive lines on a rubber substrate, the fabrication of fully stretchable wearable sensors remains limited which needs future research in this area for the advancement of wearable sensors.

Aluminum alloy is considered an ideal material in aerospace, automobile and other fields because of its lightweight, high specific strength and easy processing. However, low hardness and strength of the surface of aluminum alloys are the main factors that limit their applications. The purpose of this study is to obtain a composite coating with high hardness and lubricating properties by applying GO–PVA over MAO coating.

A pulsed bipolar power supply was used as power supply to prepare the micro-arc oxidation (MAO) coating on 6061 aluminum sample. Then a graphene oxide-polyvinyl alcohol (GO–PVA) composite coating was prepared on MAO coating for subsequent experiments. Samples were characterized by Fourier infrared spectroscopy, X-ray diffraction, Raman spectroscopy and thermogravimetric analysis. The friction test is carried out by the relative movement of the copper ball and the aluminum disk on the friction tester.

Results showed that the friction coefficient of MAO samples was reduced by 80% after treated with GO–PVA composite film.

This research has made a certain contribution to the surface hardness and tribological issues involved in the lightweight design of aluminum alloys.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2023-0427/