Search results

The purpose of this study was to investigate the efficiency of low temperature fractional crystallization to increase polyunsaturated fatty acid (PUFA) content of fish oil. Effects of temperature, stages of crystallization, rate of cooling, agitation and addition of primary nucleus on separation efficiency were evaluated. Low temperature crystallization of triacylglycerols (TAGs) was used to increase PUFA content of fish oil (initial PUFA content ∼30 g/100 g oil).

To optimize the fractionation process, the effect of fractionation temperature (7, 5, 0 and −5°C), crystallization procedures, cooling rate, agitation and addition of primary nucleus on PUFA content was evaluated.

The best relationship between PUFA concentration (45.8 g/100 g oil) and PUFA yield (51.5 per cent) was attained by performing two-stage crystallization of TAGs at the final temperatures of 5 and 0°C under slow cooling rate (3°C h−1 for first fractionation procedure and 0.7°C h−1 for second stage, until the final fractionation temperature, 0°C, was reached) and slow agitation (3 rpm) and in the presence of primary nucleus, which resulted in 50 per cent increase in PUFA content over the original fish oil.

Determination of iodine and saponification values, refractive index, solid fat content, melting point, cholesterol content of original oil and final fractionated product with the highest PUFA ratio showed that fractionation significantly alters physical and chemical properties of the fraction.

Comparison of iodine value, saponification value, refractive index, solid fat content, melting point and cholesterol content of original oil and the final fractionated product (with the highest PUFA ratio) showed that the fractionation process significantly alters mentioned properties of the initial oil.

Carotenoids have been extensively used in many industries owing to their colorant and strong antioxidant properties. Because of their useful properties, the purpose of this paper is to investigate the effect of penicillin‐adding time on stimulation of carotenoid production by Neurospora intermedia, and the effect of drying methods on stability of synthesized carotenoids.

In the first stage, curve of growth kinetic of cultures incubated at 31°C and different times (24, 48, 72, 80, 96, 104, 112, 120, 128, 136 and 144 h) to determine log and stationary phases was depicted. Then penicillin (1 mg/l) at initial and middle of log phase and initial of stationary phase was applied and its effect on carotenoid production was evaluated. In the second stage, mycelia containing carotenoid were dried by microwave oven, vacuum microwave, vacuum oven and freeze drier. Thereafter, effect of drying methods applied on stability of synthesized carotenoid was determined.

The results showed that penicillin could stimulate carotenoid biosynthesis in N. intermedia. Furthermore, this study indicated that the best time of penicillin adding is middle of log phase or after this time. Also the study indicated that there was a significant difference among applied methods as microwave‐dried mycelium had the highest carotenoid contents in comparison to the other drying methods.

This paper is believed to be the only one which investigates the effect of different factors on stimulate and stability of synthesized carotenoid by N. intermedia. Also mycelia containing carotenoid were dried by using new drying methods.

The purpose of this paper is to investigate the tensile strength, Young’s modulus, dimensional stability and porosity of acrylonitrile butadiene styrene (ABS)–oil palm fiber composite filament for fused deposition modeling (FDM).

A new feedstock material for FDM comprising oil palm fiber and ABS as a matrix was developed by a twin screw extruder. The composite filament contains 0, 3, 5 and 7 Wt.% of oil palm fiber in the ABS matrix. The tensile test is then performed on the fiber composite filament, and the wire diameter is measured. In this study, the Archimedes method was used to determine the density and the porosity of the filament. The outer surface of the wire composite was examined using an optical microscope, and the analysis of variance was used to assess the significance and the relative relevance of the primary factor.

The results showed that increasing the fiber loading from 0.15 to 0.4 MPa enhanced tensile strength by 60%. Then, from 16.1 to 18.3 MPa, the Young’s modulus rose by 22.8%. The density of extruded filament decreased and the percentage of porosity increased when the fiber loading was increased from 3 to 7 Wt.%. The diameter deviation of the extruded filaments varied from −0.21 to 0.04 mm.

This paper highlights a novel natural resource-based feedstock material for FDM. Its mechanical and physical properties were also discovered.

The purpose of this paper is to investigate the fracture properties of hybrid woven bamboo (WB)/woven e-glass (EG) fiber composites with various layer arrangements. This paper utilized a specific type of bamboo species named Gigantochloa Scortechinii (Buluh Semantan).

In these experiments, unsaturated polyester, woven EG and WB fibers were prepared through the hand lay-up technique. The composite bamboo strips were prepared in 1.5 mm thickness. The strips are woven to make a single layer. The layer was then laminated into several thicknesses. The specimens were then characterized using compact tension fracture tests.

The fracture toughness of 12–14 MPa was obtained. These findings suggest that this hybrid bamboo composite provides superior fracture strength that is equivalent with steel alloy and is extremely a good alternative for reinforcing fibers to combat fracture failures of materials and structures.

In this paper, experimental determination of newly developed composite made of WB and woven EG is presented.

This study aims to investigate Feng Shui elements that can influence housing selection and property pricing in the Malaysian housing market.

A structured questionnaire encompassing 26 Feng Shui elements, which were shortlisted based on relevant previous studies, was distributed to prospective homebuyers in the Klang Valley region. The elements were inferred and ranked according to frequency, significance and importance scores. Kruskal–Wallis ANOVA tests were used to assess the ratings provided by the different respondent groups, while Spearman's rank correlation tests were utilised to measure the degree of agreement or disagreement among each pair of the ethnic group.

The results obtained indicate the following as the five most influential elements: orientation, main entrance, street location, house number and living room. Despite a multiethnic and multicultural society in Malaysia, Spearman's rank correlation tests showed that there are no differences in the prioritisation of Feng Shui elements between three distinct ethnic groups (Malay, Chinese and Indian). However, the distribution scores are statistically different between the groups. Comparing income level with Feng Shui inclinations, the three most frequently considered elements across the three income groups consistently include orientation, main entrance and street location.

The findings of this study are expected to provide guidance to property stakeholders (developers, real estate agencies, architects, local authorities) in their future development projects. For homebuyers, this study serves as a property Feng Shui checklist for home selection and investment.

This study explored the association of Feng Shui principles to housing selection and property pricing based on cultural and income factors. These findings provide useful insights for designing and positioning of residential properties in both primary and secondary housing markets in Malaysia and beyond.