Search results

Discusses the results of a study of the moduli of elasticity of concretes made with artificially manufactured lightweight aggregates subjected to uniaxial compression and uniaxial tension. Two artificially manufactured lightweight aggregates and one normal weight aggregate (for comparison) were used in the investigation. Concrete mixes designed to have compressive strengths varying from 20 MPa to 60 MPa were used in this study. Presents the results of static and dynamic moduli of elasticity, Poisson′s ratio, ultrasonic pulse velocity, compressive strength and tensile strength tests. Observes that the static modulus of elasticity in tension is nearly equal to the static modulus of elasticity in compression at a stress level of one‐third the ultimate stress. Compressive modulus values are shown to be dependent on the stress level and type of modulus, i.e. either secant or tangent. On the other hand, the tensile modulus is not affected by the stress level. The modulus of elasticity of lightweight aggregate concrete is about 60‐70 per cent of that of normal weight concrete. Compares the test results obtained in this study with research work carried out on other lightweight aggregate concretes by other investigators. Also presents the relationships between static modulus of elasticity, dynamic modulus of elasticity, compressive strength, and Poisson′s ratio, and equations for estimating elastic modulus and Poisson′s ratio.

The purpose of this paper is to study the effect of the relative density and geometric parameters on the homogenised in-plane elasticity modulus of a cellular honeycomb structure using analytical and numerical approaches.

In this work, the mechanical behaviour of a new design of the honeycomb is analysed through a refined analytical model that is developed based on the energy theorems by considering the shearing and stretching effects in addition to bending.

By taking into account the various deformation mechanisms (MNT), the obtained results show that the values of elasticity modulus are the same for low relative densities, but the difference becomes remarkable for higher densities. Moreover, it is difficult to judge the effect of the relative density and anisotropy of the cellular structure on the values of the homogenised elasticity modulus without considering all the three deformation mechanisms in the analytical model. It is shown that conventional models overestimate the elasticity modulus, especially for high relative densities.

In this paper, a refined model that takes into account the three deformation mechanisms (MNT) is developed to predict the in-plane elasticity modulus of a honeycomb cellular material. It is shown that analytical models that describe the anisotropic behaviour of honeycomb cells can be improved by considering the three deformation mechanisms, which are bending, stretching, and shearing deformations.

Aim of this research work is to examine the stress–strain behavior and modulus of elasticity of fiber-reinforced concrete (FRC) exposed to elevated temperature. The purpose of this paper is to study the effect of standard fire exposure on the mechanical and microstructure characteristics of concrete specimens with different strength grade.

An electrical bogie hearth furnace was developed to simulate the ISO 834 standard fire curve. Specimens were exposed to high temperatures of 821°C, 925°C and 986°C for the duration of 30, 60 and 90 min, respectively, as per standard fire curve. Peak stress, peak strain, modulus of elasticity and damage level of heated concrete specimens were evaluated by experimental investigation. SEM-based microstructure investigation has been carried out to analyze the microstructure characteristics of heated concrete specimens.

The results revealed that carbon fiber reinforced concrete was found to be better than the FRC made with other fibers on improving the modulus of elasticity of concrete. An empirical relationship has been established to predict the modulus of elasticity of temperature exposed specimens with different type of fiber and grade of concrete. In comparison with low melting point fibers, high melting point fibers exhibited higher modulus of elasticity under all tested conditions. Surface damage and porosity level of concrete with carbon and basalt fibers were found to be lower than other FRC.

Empirical relationship was developed to determine the modulus of elasticity of concrete exposed to elevate temperature, and this will be useful for concrete design applications. This research work may be useful for finding the residual compressive strength of concrete exposed to elevate temperature. So that it will be helpful to identify the suitable repair/retrofitting technique for reinforced concrete elements.

The purpose of this paper is to describe various aspects of the visco-elastoplastic (VEP) behavior of porous-hardened concrete samples in relation to standard tests.

The problem is formulated on the basis of the rheological-dynamic analogy (RDA). In this study, changes in creep coefficient, Poisson's ratio, damage variables, modulus of elasticity, strength and angle of internal friction as a function of porosity are defined by P and S wave velocities. The RDA model provides a description of the degradation process of material properties from their peak state to their ultimate values using void volume fraction (VVF).

Compared to numerous versions of acoustic emission tracking developed to analyze the behavior of total wave propagation in inhomogeneous media with density variations, the proposed model is comprehensive in interpretation and consistent with physical understanding. The comparison of the damage variables with the theoretical variables under the assumption of spherical voids in the spherical representative volume element (RVE) shows a satisfactory agreement of the results for all analyzed samples if the maximum porosities are used for comparison.

The paper presents a new mathematical-physical method for examining the effect of porosity on the characteristics of hardened concrete. Porosity is essentially related to density variations. Therefore, it was logical to define the limit values of porosity using the strain energy density.

The purpose of this paper is to study the influence of the porous structure on the maximum stress and modulus of elasticity of the specimens which are fabricated by rapid prototypes. According to the experimental results, modify the theoretical formula of elastic modulus.

The Objet Eden 250 was used to prepare the Vero White photosensitive resin samples with different porosity (ranges from 25 to 65 per cent) and different pore structures. The mechanical properties of different samples were numerically simulated and the formulas of the modulus of elasticity were established. Through the compression test, the performance of the specimen is compared and analyzed, and the theoretical elastic modulus formula is optimized.

With the increase of porosity, the maximum stress of honeycomb structure specimens decreases. The maximum stress of the honeycomb structure specimen with circular pore shape is higher than the hexagon cross-section while the hexahedron and octahedron structure are the arms (wall thickness between pores) with a square cross-section. The error comparison between the modulus of elasticity before and after the structure models regression analysis shows that after the regression analysis, the error of theoretical value and the actual value is between 0 and 14 per cent which is lower than the value before the regression analysis which was between 5 and 27 per cent.

The paper obtains rules of the influence of different porous structures which were fabricated by the Vero White photosensitive resin material on mechanical properties and higher prediction accuracy formula of elastic modulus. The conclusions provide a theoretical basis for Northeastern University, China, to reduce mass and mechanical properties prediction of load-bearing parts.

Self‐compacting concrete (SCC) offers several economic and technical benefits; the use of steel fibers extends its possibilities. Steel fibers bridge cracks, retard their propagation, and improve several characteristics and properties of the SCC. The purpose of this paper is to investigate the effects of type and volume fraction of steel fiber on the compressive strength, split tensile strength, flexural strength and modulus of elasticity of steel fiber reinforced self‐compacting concrete (SFRSCC).

For this purpose, Micro wire and Wave type steel fibers with l/d ratios of 50 were used. Three different fiber volumes were added to concrete mixes at 0.5, 0.75 and 1 per cent by volume of SCC. Six different SFRSCC mixes were prepared. After 28 days of curing, compressive, split and flexural strength and modulus of elasticity were determined.

It was found that, inclusion of steel fibers significantly affect the split tensile and flexural strength of SCC accordance with type and v_f. Besides, mathematical expressions were developed to estimate the flexural, modulus of elasticity and split tensile strength of SFRSCCs regarding of compressive strength.

It was found that inclusion of steel fibers significantly affected the split tensile and flexural strength of SCC accordance with type and f v.

Currently, many experimental studies on the properties and behavior of rubberized concrete are available in the literature. These findings have motivated scholars to propose models for estimating some properties of rubberized concrete using traditional and advanced techniques. However, with the advancement of computational techniques and new estimation models, selecting a model that best estimates concrete's property is becoming challenging.

In this study, over 1,000 different experimental findings were obtained from the literature and used to investigate the capabilities of ten different machine learning algorithms in modeling the hardened density, compressive, splitting tensile, and flexural strengths, static and dynamic moduli, and damping ratio of rubberized concrete through adopting three different prediction approaches with respect to the inputs of the model.

In general, the study's findings have shown that XGBoosting and FFBP models result in the best performances compared to other techniques.

Previous studies have focused on the compressive strength of rubberized concrete as the main parameter to be estimated and rarely went into other characteristics of the material. In this study, the capabilities of different machine learning algorithms in predicting the properties of rubberized concrete were investigated and compared. Additionally, most of the studies adopted the direct estimation approach in which the concrete constituent materials are used as inputs to the prediction model. In contrast, this study evaluates three different prediction approaches based on the input parameters used, referred to as direct, generalized, and nondestructive methods.

Concrete, the second most used material in the world, surpassed only by water, relies on a vast amount of cement. The process of cement production emits substantial amounts of carbon dioxide (CO₂). Consequently, it is crucial to search for cement alternatives. Geopolymer concrete (GC) uses industrial by-product material instead of traditional cement, which not only reduces CO₂ emissions but also enhances concrete durability. On the other hand, the disposal of concrete waste in the landfills represents a significant environmental challenge, emphasising the urgent need for sustainable solutions. This study aimed to investigate waste concrete's best form and rate as the alternative aggregates in self-compacting and ambient-cured GC to preserve natural resources, reduce construction and demolition waste and decrease pertinent CO₂ emissions. The binding material employed in this research encompasses fly ash, slag, micro fly ash and anhydrous sodium metasilicate as an alkali activator. It also introduces the best treatment method to improve the recycled concrete aggregate (RCA) quality.

A total of25%, 50% and 100% of coarse aggregates are replaced with RCAs to cast self-compacting geopolymer concrete (SCGC) and assess the impact of RCA on the fresh, hardened and water absorption properties of the ambient-cured GC. Geopolymer slurry was used for coating RCAs and the authors examined the effect of one-day and seven-day cured coated RCA. The mechanical properties (compressive strength, splitting tensile strength and modulus of elasticity), rheological properties (slump flow, T500 and J-ring) and total water absorption of RCA-based SCGC were studied. The microstructural and chemical compositions of the concrete mixes were studied by the methods of energy dispersive X-Ray and scanning electron microscopy.

It is evident from the test observations that 100% replacement of natural aggregate with coated RCA using geopolymer slurry containing fly ash, slag, micro fly ash and anhydrous sodium metasilicate cured for one day before mixing enhances the concrete's quality and complies with the flowability requirements. Assessment is based on the fresh and hardened properties of the SCGC with various RCA contents and coating periods. The fresh properties of the mix with a seven-day curing time for coated RCA did not meet the requirements for self-compacting concrete, while this mix demonstrated better compressive strength (31.61 MPa) and modulus of elasticity (15.39 GPa) compared to 29.36 MPa and 9.8 GPa, respectively, for the mix with one-day cured coated RCA. However, incorporating one-day-cured coated RCA in SCGC demonstrated better splitting tensile strength (2.32 MPa) and water absorption (15.16%).

A potential limitation of this study on SCGC with coated RCAs is the focus on the short-term behaviour of this concrete. This limited time frame may not meet the long-term requirements for ensuring the sustained durability of the structures throughout their service life.

This paper highlights the treatment technique of coating RCA with geopolymer slurry for casting SCGC.

The paper aims to discuss the design, fabrication, communication, testing, and simulation of a new tactile probe called Elastirob used to measure the modulus of elasticity of biological soft tissues and soft materials.

Both finite element modeling and experimental approaches were used in this analysis. Elastirob, with the ability to apply different rates of strain on testing specimens, is accompanied by a tactile display called TacPlay. This display is a custom‐designed user‐friendly interface and is able to evaluate the elasticity in each part of the stress‐strain curve.

A new device is being constructed that can measure the modulus of elasticity of a sensed object. The results of Elastirob applied on two specimens are reported and compared by the results of experiments obtained by an industrial testing machine. Acceptable validations of Elastirob were achieved from the comparisons.

The designed system can be miniaturized to be used in minimally invasive surgeries in the future.

Elastirob determines the elasticity by drawing the stress‐strain curve and then calculating its slope. The combination of the force sensing resistor, microcontroller and stepper motor provides Elastirob with the ability to apply different rates of strain on testing specimens.

It can be employed in both in vivo and in vitro tests for measuring stiffness of touch objects. For the first time, a device has been designed and tested which is a few orders of magnitude smaller than its industrial counterparts and has considerably lower weight.

The purpose of this paper is to solve temperature stress for bending beam with different moduli under different constraints subject to nonlinear temperature.

The equations of neutral axis position, normal stress, and displacement of bending beam with different moduli subjected to nonlinear temperature were derived based on different moduli elasticity theory. Meanwhile, iterative procedure was programmed to solve the nonlinear equations. The analytical solution can return back into the result of the same modulus theory, and the analytical solution was compared with finite element numerical solution. It shows that the analytical model proposed in this paper is reliable to use. Furthermore, the influence of different moduli characteristics on the temperature stress and deformation is discussed.

The mechanical behavior of the bending beam with different moduli subject to nonlinear temperature is quite different from the one that is subjected to force. The bending beam maybe exist two neutral axis, and the reasonable selection of tension modulus and compression modulus can improve the distribution of the normal stress and reduce the maximum tensile stress or the maximum compressive stress.

The crack produced by temperature stress will affect the integrity and the durability of the structure. The solution for temperature problem with different moduli theory is rarely reported at home and board. In view of this, this paper will do some exploratory research-temperature stress for bending beam with different moduli.