Search results

To extend the reuse method and rate of straw biomass, this paper investigated the effect of lignin synthetic phenolic resin (LPF) on the rheological properties of asphalt binder.

Four LPFs with 25%, 50%, 75% and 100% substitution rates were prepared by replacing phenol with lignin in synthetic resins and using it as a modifier to prepare a bio-asphalt binder. Temperature sweep tests were conducted to evaluate aging resistance and temperature sensitivity of the bio-asphalt binder. The rutting resistance of the bio-asphalt binder was evaluated by frequency sweeps and multiple stress creep recovery (MSCR) test. Linear amplitude sweep (LAS) tests were conducted to evaluate the fatigue resistance of the bio-asphalt binder. A master curve was constructed to further analyze the rheological properties of the bio-asphalt binder at different frequencies. The low-temperature cracking resistance of the binder was evaluated by G-R parameters, critical temperatures and ΔTc. Fourier transform infrared spectroscopy (FTIR) was performed to investigate the changes in the functional groups of the binder before and after aging.

The results indicated that adding LPF could improve the high-temperature rutting resistance, fatigue resistance, aging resistance of asphalt and the binders are less affected by temperature. Additionally, LPF slightly prohibited the low-temperature performance of the asphalt binder, which, however, was significantly lower than the base asphalt degradation during aging. Compared with base asphalt binders, the bio-asphalt binder showed no new absorption peaks generated after adding LPF, identifying that the improved asphalt binder performance by LPF was a mainly physical modification.

The main objective of this paper is to further improve the substitution rate (i.e. the mass substitution ratio of lignin to phenol) of lignin and broaden the application of biomass resins, thus realizing resource sustainability.

Nowadays, researchers are interested in using the material at nanoscales as one of asphalt binder modifier. In this paper, Malaysian asphalt binder was modified with nanoclay and warm asphalt additives (WAA) and tested to determine the physical properties and storage stability. The results of the investigation indicated that the modified asphalt binders were stable in term of storage and they also have potential to improve physical properties of asphalts such as increasing softening point and decreasing the penetration. In addition, there was a significant reduction of temperature for mixing and compaction of asphalt mixtures.

This paper aims to investigate the best methods of utilisation of reclaimed asphalt pavements (RAP) in Egypt, to determine the effect of using 100% RAP instead of using virgin aggregates and asphalt; investigate the effect of thermoplastic elastomer polymer as asphalt modifier; and also improve the mechanical and physical characteristics and consequently improving the quality of asphalt paving, increasing service life of asphalt-paving and reducing costs.

Nano acrylate terpolymers were prepared with different % (Wt.) of and were characterised by Fourier transforms infrared (FTIR), for molecular weight (Mw), by thermo gravimetric analysis (TGA) and by transmission electron microscopy (TEM). A 4% (Wt.) of the prepared nanoemulsion terpolymer was mixed with virgin asphalt as a polymer modifier, to improve and reuse of the RAP. The modified binder was tested. The tests conducted include penetration, kinematic viscosity, softening point and specific gravity. Application of Marshall mix design types; hot mix asphalt (HMA), warm mix asphalt (WMA) and cold in place recycled (CIR). Four different mix designs used; control mix contained virgin asphalt by HMA, and the other three mix designs were polymermodified asphalt sample by HMA, WMA and CIR.

The research results showed that using 4 Wt.% of the prepared nanoemulsion terpolymer to produce hot mix asphalt (HMA) and warm mix asphalt (WMA) achieved higher stability compared to the control mix and cold in place recycled (CIR).

This paper discusses the preparation and the characterisation of nanoemulsion and its application in RAPs to enhance and improve the RAP quality.

Nano-acrylate terpolymer can be used as a new polymer to modify asphalt to achieve the required specifications for RAP.

According to the most recent surveys, Europe produced 265 tonnes of asphalt for road applications in 2014, while the amount of available RAP was more than 50 tonnes. The use of RAP in new blended mixes reduces the need of neat asphalt, making RAP recycling economically attractive.

In order to evaluate the rheological properties of asphalt more comprehensively and effectively, and to explore and discuss the practicability of relevant models in the evaluation of the rheological properties of asphalt.

Based on the rheological and viscoelastic theories, temperature scanning, frequency scanning and multiple stress creep recovery (MSCR) tests of different modified asphalt were carried out by dynamic shear rheometer (DSR) to obtain relevant viscoelastic parameters and evaluate the high temperature properties of different modified asphalt. Based on the time-temperature equivalence principle, the main curve was constructed to study the viscoelastic properties of asphalt in a wider frequency domain. The main curve was fitted with the CAM model, and the rheological properties of different modified asphalt were evaluated through the analysis of model parameters. The creep stiffness and creep velocity of different modified asphalt were obtained through the rheological test of bending beam (BBR), and the low-temperature performance of different modified asphalt was analyzed by using Burgers model to fit the creep compliance.

The results show that the high temperature rheological properties of several modified asphalt studied in the test are ranked from best to worst as follows: PE modified asphalt > SBS modified asphalt > SBR modified asphalt. Short-term aging can improve the high temperature performance of asphalt, and different types of modifiers can promote or inhibit this improvement effect. Based on BBR test and Burgers model fitting analysis, SBR modified asphalt has the best low temperature performance, followed by SBS modified asphalt, while PE modified asphalt has poor low temperature performance, so it is not suitable to be used as road material in low temperature area.

Combined with effective evaluation methods, the rheological properties of asphalt at different temperatures and angles were systematically evaluated, and the evolution of rheological properties of asphalt characterized by model parameters was further analyzed by advanced model simulation.

In high-temperature regions (tropical regions) temperatures rises in summer, which affects the performance of asphalt pavement. Therefore, we must consider the conditions of asphalt pavement, especially in these regions. This study aims to investigate the influence of high temperature on the stability performance of high-density polyethylene (HDPE) and crumb rubber powder (CRP) modified hot mix asphalt (HMA) using Marshall design parameters and rutting test.

In this study, three HMA mixtures with 4 per cent HDPE and 15 per cent CRP, 5 per cent HDPE and 10 per cent CRP, and 6 per cent HDPE and 5 per cent CRP concentrations were used for the Marshall stability test and dynamic stability (rutting test) at 60-75°C, and water stability test at 60°C.

The results showed that when test temperature was increased from 60°C to 75°C, the Marshall stability and dynamic stability of three HDPE- and CRP-modified HMA mixtures decreased, and these three HDPE- and CRP-modified HMA mixtures have a good moisture damage resistance. Of the three HMA mixtures with different HDPE and CRP concentrations, HMA mixtures with 5 per cent HDPE and 10 per cent CRP concentration exhibit optimal Marshall stability, dynamic stability and water stability.

This study showed the effects of high-temperatures changes on the stability performance of HDPE- and CRP-modified HMA mixtures.

The purpose of this paper is to study the recent work carried out in enhancing the properties of bitumen using nano-additives. Bitumen is a by-product obtained from the refining process of crude oil, therefore making it a diminishing product. It has been used by mankind since ages for various applications like sealants, binders, waterproof coatings and pavement construction material. It is a black viscous substance with adhesive nature.

Bitumen is used as a binding material because of its ability to become liquid when heated and become solid when cooled and thus used largely in construction of roads because of its unique properties. Low softening point of bitumen leads to melting of bitumen during summer and causes rutting of roads, whereas during winter it leads to cracking as bitumen acts brittle in nature during low temperature. Increasing global demand of bitumen has created gap between demand and supply which is increasing with the passage of time. Further modern life has created very high traffic volume and heavy load which makes it essential to improve performance of bitumen.

Research studies have reported that the thermal properties of bitumen are enhanced by using thermoplastic polymers such as styrene-butadiene-styrene, polyethylene and ethylene-vinyl acetate, rubber and bio waste etc.

This paper reviews various types of materials which have been used to improve the properties of bitumen and explores the possibility to synthesise bitumen composite materials with nanoadditives with improved structural, mechanical and thermal properties.

Cracking, deformation and rutting are the most prevalent types of pavement distress, and these deformations and flow characteristics greatly distress the pavement features while also limiting its use. In India, on the other hand, more than 300 million scrap tyres are generated each year, and their disposal has become a severe environmental issue. Furthermore, the scrap generated by the used tyre must be disposed of properly. Hence, this study presents the experimental investigations of bitumen incorporating with Crumb rubber as main additive along with SBS polymer, to enhance the engineering property.

Crumb rubber (CR) was used as an additive along with styrene–butadiene–styrene (SBS) polymer to enrich the engineering qualities of the bitumen to reduce the disposal problem of scrap tyres and reduce the risk of environmental pollution. Because SBS polymer is expensive, response surface methodology modelling's central composite design (CCD) was used to optimise the number of tests. CCD modelling's input factors (process variables) were the inclusion rates of SBS and CR, which ranged from 2% to 5% and 4% to 10%, respectively, by total weight. Furthermore, the influence of SBS polymer and CR on the characteristics of modified bitumen was prioritised.

The addition of SBS and CR enhanced the bitumen's penetration resistance at service temperatures. Furthermore, increasing the SBS and CR concentration affected the flow characteristics of the modified bitumen and enhanced its viscosity. The addition of SBS and CR as bitumen modifiers increased penetration resistance by 24.06%. The Dynamic Shear Rheometer test demonstrated that the complex modulus of virgin bitumen increases with increasing SBS and CR content, which is consistent with the shifting softening point trend. The dosing rate of up to 3.5% SBS and 11% CR considerably contributed to the creation of polymer link networks, which increased the complex modulus of the bitumen by 16.5%. The CCD model's analysis of variance and Pareto bar chart demonstrated that the dose of CR is significant in improving the engineering features of the virgin bitumen rather than the SBS.

The utilisation of CR as a bitumen modifier may solve the problem of waste tyre disposal while also lowering the risk of environmental damage. Furthermore, because the presence of CR increased the engineering properties, particularly the complex modulus of virgin bitumen, the use of CR in combination with SBS polymer can be an efficient and cost-effective strategy to improving bitumen qualities.

Natural good-quality sources of aggregates are depleting, whereas large amount of reclaimed asphalt pavement (RAP) is produced annually. Safe disposal and use of RAP in the cold in-place recycling (CIR) using foamed bitumen could be sustainable approach where milling and mixing operations are accomplished simultaneously. This will not only help in minimizing contamination (probability) and transportation cost but also reduces the carbon footprints. Therefore, this study aims to investigate the scope of RAP utilization up to 100% and further its effect on the behavior of reclaimed asphalt foamed bituminous mix.

Reclaimed asphalt foamed bituminous mix (FBM) is still a new technique. The evidence of performance of 100% recycled pavement (CIR) is only anecdotal and lacks in systematic guidelines and literatures. Foam binder coating around the aggregates is also a concern. Therefore, this study is mainly emphasized to investigate the scope of RAP use in the FBM up to 100%. RAP content is varied in each trial, i.e. 70, 85, 100 and 0% (only fresh aggregates), to make the FBM. RAP use and its effect on the behavior of FBM in terms of resilient modulus, variation in resilient modulus with curing, rutting performance and the potential of resistance against the moisture damage are addressed.

Considering the laboratory studies, it can be accomplished that mechanistic properties and performance of FBM are largely influenced by RAP material and portray less susceptible characteristics against the moisture damage. FBM containing 70% RAP content exhibits maximum resilient modulus. However, use of RAP up to 100% in FBM is satisfying the minimum required specification.

Overall, the study may be helpful to highway professionals and could generate another possible option of 100% RAP replacing fresh aggregates in the flexible pavements.

Porous asphalt has been used for than 50 years, but it was originally developed in 1970 at Franklin institute in Philadelphia, Pennsylvania. By 1974 the first formalized procedure was created by the federal highway administration to design mixtures. Many researches on porous asphalt mixture have been conducted for the past two decades. However, there remains some concern about the potential adverse impacts of infiltrated surface water on the underlying groundwater. The purpose of this paper is to presents a short review on the application of porous asphalt pavement stormwater treatment.

In this paper, a critical review on history and benefits is presented followed by review of general studies of using porous asphalt pavement, and some recent scientific studies that examine potential contamination of soil and groundwater because of infiltration systems.

This paper indicates that porous asphalt pavement is more efficient than conventional pavements in terms of retaining pollutants, improving the quality of water and runoff while maintaining infiltration.

This paper may also help reduce land consumption by reducing the need for traditional storm-water management structures. However, on the other hand, the priority objectives which is minimizing increased flooding and pollution risks while increasing performance efficiency and enhancing local environmental quality-of-life is achieved.

In order to determine the range of medium temperature zone of road asphalt, it is hoped that the evolution of viscoelastic characteristics of road asphalt under medium temperature state can be deeply explored.

In this paper, the needle penetration test and temperature scanning test were designed for 90# and 70# bitumen as test materials, and the boundary of medium temperature zone of 90# and 70# bitumen was accurately determined by data analysis method. A mathematical model was established based on principal component analysis, and a comprehensive evaluation index was proposed to evaluate the evolution of temperature viscoelastic characteristics of road asphalt by means of standardization and rotational dimensionality reduction.

The test results show that the medium temperature zone of 90# asphalt is [−5 ± 1°C, 38 ± 1°C], and the medium temperature zone of 70# asphalt is [0 ± 1°C, 51 ± 1°C]. According to the viscoelastic response of road asphalt in the medium temperature zone, the medium temperature zone can be divided into three evolution stages: weak viscoelastic stage, viscoelastic equilibrium stage, strong viscoelastic weak stage. Analysis based on the intrinsic viscosity fillip target describing the various intrinsic viscoelastic index represents the viscoelastic properties of bitumen from different angles, and limitations inherent stick fillip for target put forward the integrated the inherent stick fillip mark information, as well as targeted and accurate evaluation of road asphalt temperature comprehensive evaluation indexes in the evolution of the viscoelastic properties of I_M-T. Finally, the temperature data of asphalt pavement in several representative regions of China are compared with the determined medium temperature region, and it is proved that the research on the evolution of viscoelastic characteristics of asphalt pavement under the medium temperature condition has important practical significance.

The boundary of medium temperature zone of 90# and 70# base asphalt was determined, and the viscoelastic characteristic evolution of road asphalt under medium temperature state was studied deeply. Aiming at the limitation of intrinsic viscoelastic index, a comprehensive evaluation index IM-T which not only integrates the information of intrinsic viscoelastic index but also can accurately evaluate the evolution of temperature viscoelastic characteristics in road asphalt is proposed.