Search results

The purpose of this paper is to develop a concept and design to cast Al alloys/metal matrix composites (MMCs) by continuous casting process. The various steps involved in the evolution of the design have been reported and discussed in this study.

On the basis of developed design concept, initial prototype design has been prepared in this study. The casting process's melt flow pattern was studied via computer simulation, and the resulting changes were implemented in the original design. The single-phase fluid flow pattern through bottom feeding technique is studied. The equipment was fabricated based on computer simulation and water modelling studies. Finally, validation was performed for the preparation of Al alloys/ MMCs after parameter optimisation. The results were observed in the optical metallography to confirm the alloying and Al MMC preparation.

The developed continuous casting process with bottom feeding technique for the addition of constituent particles shows more efficiency in comparison to the existing batch processes. The final manufactured setup demonstrates effective Al alloy/MMC production as the basis for final fabrication has been accomplished by both computer simulation and water model test. In addition, the microstructure exhibits homogeneous distribution, validating the reliability of the setup.

Integrating continuous casting with continuous reinforcement or master alloy addition is novel in this area. The constraints that batch production had that have been rectified will also lower the contemporary cost of production.

A novel type of heat transfer fluid known as hybrid nanofluids is used to improve the efficiency of heat exchangers. It is observed from literature evidence that hybrid nanofluids outperform single nanofluids in terms of thermal performance. This study aims to address the stagnation point flow induced by Williamson hybrid nanofluids across a vertical plate. This fluid is drenched under the influence of mixed convection in a Darcy–Forchheimer porous medium with heat source/sink and entropy generation.

By applying the proper similarity transformation, the partial differential equations that represent the leading model of the flow problem are reduced to ordinary differential equations. For the boundary value problem of the fourth-order code (bvp4c), a built-in MATLAB finite difference code is used to tackle the flow problem and carry out the dual numerical solutions.

The shear stress decreases, but the rate of heat transfer increases because of their greater influence on the permeability parameter and Weissenberg number for both solutions. The ability of hybrid nanofluids to strengthen heat transfer with the incorporation of a porous medium is demonstrated in this study.

The findings may be highly beneficial in raising the energy efficiency of thermal systems.

The originality of the research lies in the investigation of the Darcy–Forchheimer stagnation point flow of a Williamson hybrid nanofluid across a vertical plate, considering buoyancy forces, which introduces another layer of complexity to the flow problem. This aspect has not been extensively studied before. The results are verified and offer a very favorable balance with the acknowledged papers.

Perspiration and heat are produced by the body and must be eliminated to maintain a stable body temperature. Sweat, heat and air must pass through the fabric to be comfortable. The cloth absorbs sweat and then releases it, allowing the body to chill down. By capillary action, moisture is driven away from fabric pores or sucked out of yarns. Convectional air movement improves sweat drainage, which may aid in body temperature reduction. Clothing reduces the skin's ability to transport heat and moisture to the outside. Excessive moisture makes clothing stick to the skin, whereas excessive heat induces heat stress, making the user uncomfortable. Wet heat loss is significantly more difficult to understand than dry heat loss. The purpose of this study is to provided a good compilation of complete information on wet thermal comfort of textile and technological elements to be consider while constructing protective apparel.

This paper aims to critically review studies on the thermal comfort of textiles in wet conditions and assess the results to guide future research.

Several recent studies focused on wet textiles' impact on comfort. Moisture reduces the fabric's thermal insulation value while also altering its moisture characteristics. Moisture and heat conductivity were linked. Sweat and other factors impact fabric comfort. So, while evaluating a fabric's comfort, consider both external and inside moisture.

The systematic literature review in this research focuses on wet thermal comfort and technological elements to consider while constructing protective apparel.

This study aims to characterize the properties of natural cellulose fiber from the pseudo-stems of the curcuma zedoaria plant.

The fiber was extracted using the biological retting process (cold-water retting). The intrinsic fiber properties obtained were used to evaluate the possibility of using fiber for textile applications.

The average length of a curcuma zedoaria fiber was 34.77 cm with a fineness value of 6.72 Tex. A bundle of curcuma zedoaria fibers was comprised of many elementary fibers. Curcuma zedoaria had an irregular cross-section, with the lumen having a varied oval shape. Curcuma zedoaria fibers had tenacity and elongation value of 3.32 gf/denier and 6.95%, respectively. Curcuma zedoaria fibers had a coefficient of friction value of 0.46. Curcuma zedoaria fibers belong to a hygroscopic fiber type with a moisture regain value of 10.29%.

Extraction and Characterization of Curcuma zedoaria Pseudo-stems Fibers for Textile Application.

This study aims to investigate the influence of corporate social responsibility (CSR) on corporate sustainable performance (CSP) of small- and medium-sized enterprises (SMEs) by looking into the significance of mediating factors, namely, brand image (BI) and brand loyalty (BL), within the context of an emerging economy.

The authors conduct an extensive literature study on the subjects of CSR, BI and BL to assess their influence on the sustainable performance of SMEs in an emerging market. The study adopts a quantitative methodology. A total of 438 answers were obtained from a sample size of 513. The data of the SMEs in Vietnam was analyzed using the smart partial least squares structural equation modeling software, specifically version 3.3.2.

The results of the authors demonstrate notable and favorable correlations between CSR and CSP, CSR and BI and CSR and BL. Importantly, the findings contribute to existing knowledge by looking into the mediating influence of BI and BL in the relationship between CSR and CSP.

According to the authors’ understanding, a number of research have investigated the correlation between CSR and CSP within the realm of SMEs. Nevertheless, there is a scarcity of scholarly research examining the mediating function of BI and BL in this association. The study’s findings have important implications for entrepreneurs and senior management in effectively guiding their enterprises and improving their business strategies with an emphasis on sustainability in emerging markets. The outcome of this study has the potential to significantly contribute to SMEs in Vietnam as well as other emerging countries.