Search results

Wireless sensor networks (WSN), as a solution for buried water pipe monitoring, face a new set of challenges compared to traditional application for above-ground infrastructure monitoring. One of the main challenges for underground WSN deployment is the limited range (less than 3 m) at which reliable wireless underground communication can be achieved using radio signal propagation through the soil. To overcome this challenge, the purpose of this paper is to investigate a new approach for wireless underground communication using acoustic signal propagation along a buried water pipe.

An acoustic communication system was developed based on the requirements of low cost (tens of pounds at most), low power supply capacity (in the order of 1 W-h) and miniature (centimetre scale) size for a wireless communication node. The developed system was further tested along a buried steel pipe in poorly graded SAND and a buried medium density polyethylene (MDPE) pipe in well graded SAND.

With predicted acoustic attenuation of 1.3 dB/m and 2.1 dB/m along the buried steel and MDPE pipes, respectively, reliable acoustic communication is possible up to 17 m for the buried steel pipe and 11 m for the buried MDPE pipe.

Although an important first step, more research is needed to validate the acoustic communication system along a wider water distribution pipe network.

This paper shows the possibility of achieving reliable wireless underground communication along a buried water pipe (especially non-metallic material ones) using low-frequency acoustic propagation along the pipe wall.

The purpose of this research is to achieve multi-task autonomous driving by adjusting the network architecture of the model. Meanwhile, after achieving multi-task autonomous driving, the authors found that the trained neural network model performs poorly in untrained scenarios. Therefore, the authors proposed to improve the transfer efficiency of the model for new scenarios through transfer learning.

First, the authors achieved multi-task autonomous driving by training a model combining convolutional neural network and different structured long short-term memory (LSTM) layers. Second, the authors achieved fast transfer of neural network models in new scenarios by cross-model transfer learning. Finally, the authors combined data collection and data labeling to improve the efficiency of deep learning. Furthermore, the authors verified that the model has good robustness through light and shadow test.

This research achieved road tracking, real-time acceleration–deceleration, obstacle avoidance and left/right sign recognition. The model proposed by the authors (UniBiCLSTM) outperforms the existing models tested with model cars in terms of autonomous driving performance. Furthermore, the CMTL-UniBiCL-RL model trained by the authors through cross-model transfer learning improves the efficiency of model adaptation to new scenarios. Meanwhile, this research proposed an automatic data annotation method, which can save 1/4 of the time for deep learning.

This research provided novel solutions in the achievement of multi-task autonomous driving and neural network model scenario for transfer learning. The experiment was achieved on a single camera with an embedded chip and a scale model car, which is expected to simplify the hardware for autonomous driving.

This paper aims to offer insight into how strategies within the accounting profession, which has been becoming more global, might be changed by the recent outbreak of the Second Cold War between the West and the Rest of the World.

We explore the strategies of those who called themselves “Confucian accountants” in China, a country which has recently discouraged its state-owned enterprises from using the services of the Big 4. We do this by employing qualitative research methods, including reflexive photo interviews, in which Big-4 accountants, recognised as the most Westernised accounting actors in China, and Confucian accountants are asked to take and explain photographs representing their professional lives. Bourdieu’s notions of “economy of practices” and “vision-of-division strategy” are drawn upon to understand who the Confucian accountants are and what they do strategically in their pursuit of a higher revenue stream and improved social standing in the Chinese social space.

The homegrown Confucian accountants share cultural-cognitive characteristics with neighbouring social actors, such as their clients and government officials, who have been inculcated with Confucianism and the state’s cultural confidence policy in pursuit of a “socialist market economy with Chinese characteristics”. Those accountants try to enhance their social standing and revenue stream by strategically demonstrating their difference from Big-4 accountants. For this purpose, they wear Confucian clothes, have Confucian props in their office, employ Confucian phrases in their everyday conversations, use Confucian business cards and construct and maintain guanxi with government officials and clients.

This paper is the first attempt to explore Confucian accountants’ strategies for increasing their revenue and social standing at the start of the Second Cold War.

This study aims to focus on the main materials used in consolidation processes of illuminated paper manuscripts and leather binding.

For each material, chemical structure, chemical composition, molecular formula, solubility, advantages, disadvantages and its role in treatment process are presented.

This study concluded that carboxy methyl cellulose, hydroxy propyl cellulose, methyl cellulose, cellulose acetate, nanocrystalline cellulose, funori, sturgeon glue, poly vinyl alcohol, chitosan, chitosan nanoparticles (NPs), gelatin, aquazol, paraloid B72 and hydroxyapatite NPs were the most common and important materials used for the consolidation of illuminated paper manuscripts. For the leather bindings, hydroxy propyl cellulose, polyethylene glycol, oligomeric melamine-formaldehyde resin, acrylic wax SC6000, pliantex, paraloid B67 and B72, silicone oil and collagen NPs are the most consolidants used.

Illuminated paper manuscripts with leather binding are considered one of the most important objects in libraries, museums and storehouses. The uncontrolled conditions and other deterioration factors inside the libraries and storehouses lead to degradation of these artifacts. The brittleness, fragility and weakness are considered the most common deterioration aspects of illuminated paper manuscripts and leather binding. Therefore, the consolidation process became vital and important to solve this problem. This study presents the main materials used for consolidation process of illuminated paper manuscripts and leather bindings.

The aim of this study is to make a contribution towards reducing the deflections of silicon wafers. The deformation of silicon wafers used in the manufacture of electronic micro-components is one of the most common problems encountered by industrialists during manufacturing. Stack warping is typically produced during the process of depositing thin layers on a substrate. This is due to the thermal-mechanical stresses caused by the difference between the thermal expansion coefficients of the materials. Reducing wafer deformation is essential to increase reliability and improve quality. In this paper, the authors propose an approach based on minimal geometrical modifications to reduce the deformation of a silicon wafer coated with two thin layers. Numerical finite element models have been developed to evaluate the impact of geometrical modifications on warping amplitude. Finite element models have been validated compared with experimental models. The results obtained are encouraging and clearly show a considerable reduction in wafer deformation.

Reducing wafer deformation is essential to increase reliability and improve quality. In this paper, the authors propose an approach based on minimal geometrical modifications to reduce the deformation of a silicon wafer coated with two thin layers. Numerical finite element models have been developed to evaluate the impact of geometrical modifications on warping amplitude. Finite element models have been validated compared with experimental models.

The results obtained are encouraging and clearly show a considerable reduction in wafer deformation.

This paper describes the influence of geometric modification on wafer deformation. The work show also the cruciality of stress reduction in the purpose to obtain less wafer deformation.

This article examines curatorial practices, both traditional and digital, in the Guizhou Provincial Museum’s ethnic exhibition to assess their effectiveness in representing ethnic minority cultures, fostering learning and inspiring curiosity about ethnic textiles and costumes and associated cultures. It also explores audience expectations concerning digital technology use in future exhibitions.

A mixed-methods approach was employed, where visitor data were collected through questionnaires, together with interviews with expert, museum professionals and ethnic minority textile practitioners. Their expertise proved instrumental in shaping the design of the study and enhancing the overall visitor experience, and thus fostering a deeper appreciation and understanding of ethnic minority cultures.

Visitors were generally satisfied with the exhibition, valuing their educational experience on ethnic textiles and cultures. There is a notable demand for more immersive digital technologies in museum exhibitions. The study underscores the importance of participatory design with stakeholders, especially ethnic minority groups, for genuine and compelling cultural representation.

This study delves into the potentials of digital technologies in the curation of ethnic minority textiles, particularly for enhancing education and cultural communication. Ethnic textiles and costumes provide rich sensory experience, and they carry deep cultural significance, especially during festive occasions. Our findings bridge this gap; they offer insights for museums aiming to deepen the visitor experiences and understanding of ethnic cultures through the use of digital technologies.

This study aims to offer a comprehensive exploration of the potential and challenges associated with sensor fusion-based virtual reality (VR) applications in the context of enhanced physical training. The main objective is to identify key advancements in sensor fusion technology, evaluate its application in VR systems and understand its impact on physical training.

The research initiates by providing context to the physical training environment in today’s technology-driven world, followed by an in-depth overview of VR. This overview includes a concise discussion on the advancements in sensor fusion technology and its application in VR systems for physical training. A systematic review of literature then follows, examining VR’s application in various facets of physical training: from exercise, skill development and technique enhancement to injury prevention, rehabilitation and psychological preparation.

Sensor fusion-based VR presents tangible advantages in the sphere of physical training, offering immersive experiences that could redefine traditional training methodologies. While the advantages are evident in domains such as exercise optimization, skill acquisition and mental preparation, challenges persist. The current research suggests there is a need for further studies to address these limitations to fully harness VR’s potential in physical training.

The integration of sensor fusion technology with VR in the domain of physical training remains a rapidly evolving field. Highlighting the advancements and challenges, this review makes a significant contribution by addressing gaps in knowledge and offering directions for future research.

The purpose of the study is to optimize the blending ratio of Arecanut and cotton fibers to create yarn with the best quality for various applications, particularly home furnishings. The study aims to determine the effect of different blend ratios on the physical and mechanical properties of the yarn.

The study involves blending Arecanut and cotton fibers in various ratios (90:10, 75:25, 50:50, 25:75 and 10:90) at two different yarn counts (10/1 and 5/1). Various physical and mechanical properties of the blended yarn are analyzed, including unevenness, coefficient of mass variation (cvm%), imperfection, hairiness, breaking strength, elongation, tenacity and breaking work.

The research findings suggest that the blend ratio of 10:90 (10% cotton and 90% Arecanut fiber) produced the best results in terms of physical and mechanical properties for both yarn counts. This blend ratio resulted in reduced unevenness, cvm% and imperfection, while also exhibiting good mechanical properties such as breaking strength, elongation, tenacity and breaking work. The blend with a higher concentration of cotton generally showed better properties due to the coarseness of Arecanut fiber. As the goal of the study was to determine the best blend ratio that included the most Arecanut fiber based on its physical and mechanical properties, which is suitable for home furnishing applications, 75:25 Areca cotton blend ratio of yarn count 5/1 proved to be the best.

The study acknowledges that Arecanut fiber must be blended with other commercially used fibers like cotton due to its coarseness. While the study provides insights into optimizing blend ratios for home furnishings and packaging, further research may be needed to make the material suitable for clothing applications.

The research has practical implications for industries interested in utilizing Arecanut and cotton blends for various applications, such as home furnishings and packaging materials. It suggests that specific blend ratios can result in yarn with desirable properties for these purposes.

The study mentions that the increased use of Arecanut fibers can benefit the growers of Arecanut, potentially providing economic opportunities for communities engaged in Arecanut farming.

The research explores the utilization of Arecanut fibers, an underutilized resource, in combination with cotton to create sustainable yarn. It assesses various blend ratios and their impact on yarn properties, contributing to the understanding of eco-friendly textile materials.

Previous literature has identified human resources as a key source of competitive advantage in organizations of all sizes. However, Small and Medium-sized Enterprises (SMEs) face difficulty in comprehensively implementing all recommended Human Resource Management (HRM) functions. In this study, we shed light on the field of HRM in SMEs by focusing on the context of Greek Small and Medium-sized Hotels (SMHs), which represent a dominant private sector employer across the country.

Using a fuzzy-set qualitative comparative analysis (fsQCA) and 34 in-depth interviews with SMHs' owners/managers, we explore the HRM conditions leading to high levels of performance, while taking into consideration the influence of internal key determinants.

We uncover three alternative successful HRM strategies that maximize business performance, namely the Compensation-based performers, the HRM developers and the HRM investors. Each strategy fits discreet organizational characteristics related to company size, ownership type and organizational structure.

To the best of the authors' knowledge this is among the first empirical studies that examine different and equifinal performance-enhancing configurations of HRM practices in SMHs.