Search results

The lean blowout (LBO) limit of the combustor is one of the important performance parameters for any gas turbine combustor design. This study aims to predict the LBO limits of an in-house designed swirl stabilized 3kW can-type micro gas turbine combustor.

The experimental prediction of LBO limits was performed on 3kW swirl stabilized combustor fueled with methane for the combustor inlet velocity ranging from 1.70 m/s to 6.80 m/s. The numerical prediction of LBO limits of combustor was performed on two-dimensional axisymmetric model. The blowout limits of combustor were predicted through calculated average exit gas temperature (AEGT) method and compared with experimental predictions.

The results show that the predicted LBO equivalence ratio decreases gradually with an increase in combustor inlet velocity.

This LBO limits predictions will use to fix the operating boundary conditions of 3kW can-type micro gas turbine combustor. This methodology will be used in design stage as well as in the testing stage of the combustor.

This is a first effort to predict the LBO limits on micro gas turbine combustor through AEGT method. The maximum uncertainty in LBO limit prediction with AEGT is 6 % in comparison with experimental results.

This paper aims to predict the effect of combustor inlet area ratio (CIAR) on the lean blowout limit (LBO) of a swirl stabilized can-type micro gas turbine combustor having a thermal capacity of 3 kW.

The blowout limits of the combustor were predicted predominantly from numerical simulations by using the average exit gas temperature (AEGT) method. In this method, the blowout limit is determined from characteristics of the average exit gas temperature of the combustion products for varying equivalence. The CIAR value considered in this study ranges from 0.2 to 0.4 and combustor inlet velocities range from 1.70 to 6.80 m/s.

The LBO equivalence ratio decreases gradually with an increase in inlet velocity. On the other hand, the LBO equivalence ratio decreases significantly especially at low inlet velocities with a decrease in CIAR. These results were backed by experimental results for a case of CIAR equal to 0.2.

Gas turbine combustors are vulnerable to operate on lean equivalence ratios at cruise flight to avoid high thermal stresses. A flame blowout is the main issue faced in lean operations. Based on literature and studies, the combustor lean blowout performance significantly depends on the primary zone mass flow rate. By incorporating variable area snout in the combustor will alter the primary zone mass flow rates by which the combustor will experience extended lean blowout limit characteristics.

This is a first effort to predict the lean blowout performance on the variation of combustor inlet area ratio on gas turbine combustor. This would help to extend the flame stability region for the gas turbine combustor.

A combustor design is a particularly important and difficult task in the development of gas turbine engines. During studies for accurate and easy combustor design, reasonable design methodologies have been established and used in engine development. The purpose of this paper is to review the design methodology for combustor in development of advanced gas turbine engines. The advanced combustor development task can be successfully achieved in less time and at lower cost by adopting new and superior design methodologies.

The review considers the main technical problems (combustion, cooling, fuel injection and ignition technology) in the development of modern combustor design and deals with combustor design methods by dividing it into preliminary design, performance evaluation, optimization and experiment. The advanced combustion and cooling technologies mainly used in combustor design are mentioned in detail. In accordance with the modern combustor design method, the design mechanisms are considered and the methods used in every stage of the design are reviewed technically.

The improved performances and strict emission limits of gas turbine engines require the application of advanced technologies when designing combustors. The optimized design mechanism and reasonable performance evaluation methods are very important in reducing experiments and increasing the effectiveness of the design.

This paper provides a comprehensive review of the design methodology for the advanced gas turbine engine combustor.

The purpose of this paper is to review the applications of the chemical reactor network (CRN) approach for modeling the combustion in gas turbine combustors and classify the CRN construction methods that have been frequently used by researchers.

This paper initiates with introducing the CRN approach as a practical tool for precisely predicting the species concentrations in the combustion process with lower computational costs. The structure of the CRN and its elements as the ideal reactors are reviewed in recent studies. Flow field modeling has been identified as the most important input for constructing the CRNs; thus, the flow field modeling methods have been extensively reviewed in previous studies. Network approach, component modeling approach and computational fluid dynamics (CFD), as the main flow field modeling methods, are investigated with a focus on the CRN applications. Then, the CRN construction approaches are reviewed and categorized based on extracting the flow field required data. Finally, the most used kinetics and CRN solvers are reviewed and reported in this paper.

It is concluded that the CRN approach can be a useful tool in the entire process of combustion chamber design. One-dimensional and quasi-dimensional methods of flow field modeling are used in the construction of the simple CRNs without detailed geometry data. This approach requires fewer requirements and is used in the initial combustor designing process. In recent years, using the CFD approach in the construction of CRNs has been increased. The flow field results of the CFD codes processed to create the homogeneous regions based on construction criteria. Over the past years, several practical algorithms have been proposed to automatically extract reactor networks from CFD results. These algorithms have been developed to identify homogeneous regions with a high resolution based on the splitting criteria.

This paper reviews the various flow modeling methods used in the construction of the CRNs, along with an overview of the studies carried out in this field. Also, the usual approaches for creating a CRN and the most significant achievements in this field are addressed in detail.

Diesel has traditionally been considered the best-suited and most widely used fuel in various sectors, including manufacturing industries, power production, automobiles and transportation. However, with the ongoing crisis of fossil fuel inadequacy, the search for alternative fuels and their application in these sectors has become increasingly important. One particularly interesting and beneficial alternative fuel is biodiesel derived from bio sources.

In this research, an attempt was made to use biodiesel in an unconventional micro gas turbine engine. It will remove the concentric use of diesel engines for power production by improving fuel efficiency as well as increasing the power production rate. Before the fuel is used enormously, it has to be checked in many ways such as performance, emission and combustion analysis experimentally.

In this paper, a detailed experimental study was made for the use of Spirulina microalgae biodiesel in a micro gas turbine. A small-scale setup with the primary micro gas turbine and secondary instruments such as a data acquisition system and AVL gas analyser. The reason for selecting the third-generation microalgae is due to its high lipid and biodiesel production rate. For the conduction of experimental tests, certain conditions were followed in addition that the engine rotating rpm was varied from 4,000, 5,000 and 6,000 rpm. The favourable and predicted results were obtained with the use of microalgae biodiesel.

The performance and combustion results were not exactly equal or greater for biodiesel blends but close to the values of pure diesel; however, the reduction in the emission of CO was at the appreciable level for the used spirulina microalgae biodiesel. The emission of nitrogen oxides and carbon dioxide was a little higher than the use of pure diesel. This experimental analysis results proved that the use of spirulina microalgae biodiesel is both economical and effective replacement for fossil fuel.

Utilizing renewable energy and developing new energy sources are practical responses to the shortage of fossil fuels and environmental regulations for carbon dioxide emissions. The purpose of this paper is to assess the practicability of using low heating value (LHV) fuel on an annular miniature gas turbine (MGT) via numerical simulations.

The MGT used in this study is MW‐44 Mark I, whose original fuel is liquid (Jet A1). Its fuel supply system is re‐designed to use biogas fuel with LHV. The simulations, aided by the commercial code CFD‐ACE+, were carried out to investigate the cooling effect in a perforated combustion chamber and combustion behavior in an annular MGT when using LHV gas. In this study, four parameters of rotational speeds are considered. At each specific speed, various mixture ratios of methane (CH₄) to carbon dioxide (CO₂) including 90, 80, 70, and 60 percent were taken into consideration as simulated LHV fuels.

The simulation results show the chamber design can create a proper recirculation zone to concentrate the flame at the center of the chamber, and prevent the flame from expanding to cause hot spot. Furthermore, the hot gas exhausted from combustor outlet is cooled down effectively by jet flow discharged from dilution holes, which prevent turbine blade from heat damage.

Simulation results demonstrate that CFD‐ACE+ can simulate flow field performance and combustion behavior in an annular MGT precisely. The results of these CFD analyses confirm that the methane fuel can be used in such small volume of MGT and still have high performance. With the aid of the constructed combustor model, the performance of a methane‐used MGT can be realized before the experiment procedure starts.

This paper seeks to evaluate the potential of heat exchanged aeroengines for future Unmanned Aerial Vehicle (UAV), helicopter, and aircraft propulsion, with emphasis placed on reduced emissions, lower fuel burn, and less noise.

Aeroengine performance analyses were carried out covering a wide range of parameters for more complex thermodynamic cycles. This led to the identification of major component features and the establishing of preconceptual aeroengine layout concepts for various types of recuperated and ICR variants.

Novel aeroengine architectures were identified for heat exchanged turboshaft, turboprop, and turbofan variants covering a wide range of applications. While conceptual in nature, the results of the analyses and design studies generally concluded that heat exchanged engines represent a viable solution to meet demanding defence and commercial aeropropulsion needs in the 2015‐2020 timeframe, but they would require extensive development.

As highlighted in Parts I and II, early development work was focused on the use of recuperation, but this is only practical with compressor pressure ratios up to about 10. For today's aeroengines with pressure ratios up to about 50, improvement in SFC can only be realised by incorporating intercooling and recuperation. The new aeroengine concepts presented are clearly in an embryonic stage, but these should enable gas turbine and heat exchanger specialists to advance the technology by conducting more in‐depth analytical and design studies to establish higher efficiency and “greener” gas turbine aviation propulsion systems.

It is recognised that meeting future environmental and economic requirements will have a profound effect on aeroengine design and operation, and near‐term efforts will be focused on improving conventional simple‐cycle engines. This paper has addressed the longer‐term potential of heat exchanged aeroengines and has discussed novel design concepts. A deployment strategy, aimed at gaining confidence with emphasis placed on assuring engine reliability, has been suggested, with the initial development and flight worthiness test of a small recuperated turboprop engine for UAVs, followed by a larger recuperated turboshaft engine for a military helicopter, and then advancement to a larger and far more complex ICR turbofan engine.

This paper aims to investigate the effect of additives in Jet-A fuel blends, especially on performance, combustion and emission characteristics.

Jet-A fuel was formed by using Kay’s and Gruenberg–Nissan mixing rules by adding additive glycerol with TiO₂. While measuring the combustion performance, the amount of oxygen content present in fuel and atomization are the key factors to consider. As such, the Jet-A fuel was created by adding additives at different proportion. A small gas turbine engine was used for conducting tests. All tests were carried out at different load conditions for all the fuel blends such as neat Jet-A fuel, G10T (glycerol 10% with 50 ppm TiO₂ and Jet-A 90%), G20T (glycerol 10% with 50 ppm TiO₂ and Jet-A 90%) and G30T (glycerol 10% with 50 ppm TiO₂ and Jet-A 90%).

From tests, the G20T and G10T produced better results than other blends. The thermal efficiency of the blends of G20T and G10T are 22% and 14% higher than neat Jet-A fuel. Further, the improved static thrust with less fuel consumption was noticed in G20T fuel blend.

The G20T blends showed better performance because of the increased oxygenated compounds in the fuel blends. Moreover, the emission rate of environmentally harmful gases such as NOx, CO and HC was lower than the neat Jet-A fuel. From the results, it is clear that the rate of exergy destruction is more in the combustion chamber than the other components of fuel.

This paper aims to study the influences of hydrogen jet pressure on flow features of a strut-based injector in a scramjet combustor under-reacting cases are numerically investigated in this study.

The numerical analysis is carried out using Reynolds Averaged Navier Stokes (RANS) equations with the Shear Stress Transport k-ω turbulence model in contention to comprehend the flow physics during scramjet combustion. The three major parameters such as the shock wave pattern, wall pressures and static temperature across the combustor are validated with the reported experiments. The results comply with the range, indicating the adopted simulation method can be extended for other investigations as well. The supersonic flow characteristics are determined based on the flow properties, combustion efficiency and total pressure loss.

The results revealed that the augmentation of hydrogen jet pressure via variation in flame features increases the static pressure in the vicinity of the strut and destabilize the normal shock wave position. Indeed, the pressure of the mainstream flow drives the shock wave toward the upstream direction. The study perceived that once the hydrogen jet pressure is reached 4 bar, the incoming flow attains a subsonic state due to the movement of normal shock wave ahead of the strut. It is noticed that the increase in hydrogen jet pressure in the supersonic flow field improves the jet penetration rate in the lateral direction of the flow and also increases the total pressure loss as compared with the baseline injection pressure condition.

The outcome of this research provides the influence of fuel injection pressure variations in the supersonic combustion phenomenon of hypersonic vehicles.

This paper substantiates the effect of increasing hydrogen jet pressure in the reacting supersonic airstream on the performance of a scramjet combustor.

This study aims to review the recent advancements in high entropy alloys (HEAs) called high entropy materials, including high entropy superalloys which are current potential alternatives to nickel superalloys for gas turbine applications. Understandings of the laser surface modification techniques of the HEA are discussed whilst future recommendations and remedies to manufacturing challenges via laser are outlined.

Materials used for high-pressure gas turbine engine applications must be able to withstand severe environmentally induced degradation, mechanical, thermal loads and general extreme conditions caused by hot corrosive gases, high-temperature oxidation and stress. Over the years, Nickel-based superalloys with elevated temperature rupture and creep resistance, excellent lifetime expectancy and solution strengthening L12 and γ´ precipitate used for turbine engine applications. However, the superalloy’s density, low creep strength, poor thermal conductivity, difficulty in machining and low fatigue resistance demands the innovation of new advanced materials.

HEAs is one of the most frequently investigated advanced materials, attributed to their configurational complexity and properties reported to exceed conventional materials. Thus, owing to their characteristic feature of the high entropy effect, several other materials have emerged to become potential solutions for several functional and structural applications in the aerospace industry. In a previous study, research contributions show that defects are associated with conventional manufacturing processes of HEAs; therefore, this study investigates new advances in the laser-based manufacturing and surface modification techniques of HEA.

The AlxCoCrCuFeNi HEA system, particularly the Al0.5CoCrCuFeNi HEA has been extensively studied, attributed to its mechanical and physical properties exceeding that of pure metals for aerospace turbine engine applications and the advances in the fabrication and surface modification processes of the alloy was outlined to show the latest developments focusing only on laser-based manufacturing processing due to its many advantages.

It is evident that high entropy materials are a potential innovative alternative to conventional superalloys for turbine engine applications via laser additive manufacturing.