Search results

This study aims to evaluate the protection performance of zinc as sacrificial anode for ABS A steel in the presence of H₂S under different temperatures, pH and salinities.

In this paper, weight loss measurements and electrochemical measurements are used to evaluate the corrosion degree of zinc and ABS A steel.

Under the conditions involved in this work, it is shown that zinc is a nice sacrificial anode with the reason of its stable potential and excellent anode current efficiency according to the relevant standard. And it is also found that the hydrogen evolution does not occur on ABS A steel specimens. The potential difference between cathode and anode is suitable; thus, it can be concluded that each steel is well protected.

To the best of the authors’ knowledge, no other study has analyzed the protection mechanism and effect of zinc as sacrificial anode in H₂S-containing environments under high temperature at present.

This study aims to discuss the influences of surface severe plastic deformation (S²PD) on the electrochemical corrosion, pitting corrosion, intergranular corrosion, stress corrosion cracking of aluminum (Al) alloys and attempt to correlate the microstructural/compositional changes with the performances.

This study provides a novel gradient design of structure/composition caused by S²PD for the purpose of enhancing Al alloys’ corrosion resistance.

S²PD has a significant effect on corrosion behavior of Al alloys through tuning the grain size, residual stress, composition, grain boundary phase and second phase particle distribution.

Although Al alloys are known to form a protective Al₂O₃ film, corrosion is a major challenge for the longevity of Al structures across numerous industries, especially for the infrastructures made of high-strength Al alloys. Traditional strategies of improving corrosion resistance of Al alloys heavily relied on alloying and coatings. In this review, gradient design of structure/composition caused by S²PD provides a novel strategy for corrosion protection of Al alloys, especially in the enhancement of localized corrosion resistance.

The purpose of this study to investigate the organized porous network zinc (OPNZ) scaffolds. Their mechanical characteristics, surface roughness and fracture mechanism were assessed in relation to their structural properties. The prospects of fused deposition modeling (FDM) for printing metal scaffolds via rapid tooling have also been studied.

Zn scaffolds with different pore and strut sizes were manufactured via the rapid tooling method. This method is a multistep process that begins with the 3D printing of a polymer template. Later, a paraffin template was obtained from the prepared polymer template. Finally, this paraffin template was used to fabricate the Zn scaffold using microwave sintering. The characterization of prepared Zn samples involved structural characterization, microstructural study, surface roughness testing and compression testing. Moreover, based on the Gibson–Ashby model analysis, the model equations’ constant values were evaluated, which can help in predicting the mechanical properties of Zn scaffolds.

The scanning electron microscopy study confirmed that the fabricated sample pores were open and interconnected. The X-ray diffraction analysis revealed that the Zn scaffold contained hexagonal closed-packed Zn peaks related to the a-Zn phase, validating that scaffolds were free from contamination and impurity. The range for ultimate compressive strength, compressive modulus and plateau stresses for Zn samples were found to be 6.75–39 MPa, 0.14–3.51 GPa and 1.85–12.6 MPa by adjusting their porosity, which are comparable with the cancellous bones. The average roughness value for the Zn scaffolds was found to be 1.86 µm.

This research work can widen the scope for extrusion-based FDM printers for fabricating biocompatible and biodegradable metal Zn scaffolds. This study also revealed the effects of scaffold structural properties like porosity, pore and strut size effect on their mechanical characteristics in view of tissue engineering applications.

Nature and occurrence of food-borne pathogens in raw and processed food products evolved greatly in the past few years due to new modes of transmission and resistance build-up against sundry micro-/macro-environmental conditions. Assurance of food health and safety thus gained immense importance, for which bio-sensing technology proved very promising in the detection and quantification of food-borne pathogens. Considering the importance, different studies have been performed, and different biosensors have been developed. This study aims to summarize the different biosensors used for the deduction of food-borne pathogens.

The present review highlights different biosensors developed apropos to food matrices, factors governing their selection, their potential and applicability. The paper discusses some related key challenges and constraints and also focuses on the needs and future research prospects in this field.

The shift in consumers’ and industries’ perceptions directed the further approach to achieve portable, user and environmental friendly biosensing techniques. Despite of these developments, it was still observed that the comparison among the different biosensors and their categories proved tedious on a single platform; since the food matrices tested, pathogen detected or diagnosed, time of detection, etc., varied greatly and very few products have been commercially launched. Conclusively, a challenge lies in front of food scientists and researchers to maintain pace and develop techniques for efficiently catering to the needs of the food industry.

Biosensors deduction limit varied with the food matrix, type of organism, material of biosensors’ surface, etc. The food matrix itself consists of complex substances, and various types of food are available in nature. Considering the diversity of food there is a need to develop a universal biosensor that can be used for all the food matrices for a pathogen. Further research is needed to develop a pathogen-specific biosensor that can be used for all the food products that may have accuracy to eliminate the traditional method of deduction.

The present paper summarized and categorized the different types of biosensors developed for food-borne pathogens.

The ability to characterise highly conducting objects, that may also be highly magnetic, by the complex symmetric rank–2 magnetic polarizability tensor (MPT) is important for metal detection applications including discriminating between threat and non-threat objects in security screening, identifying unexploded anti-personnel landmines and ordnance and identifying metals of high commercial value in scrap sorting. Many everyday non-threat items have both a large electrical conductivity and a magnetic behaviour, which, for sufficiently weak fields and the frequencies of interest, can be modelled by a high relative magnetic permeability. This paper aims to discuss the aforementioned idea.

The numerical simulation of the MPT for everyday non-threat highly conducting magnetic objects over a broad range of frequencies is challenging due to the resulting thin skin depths. The authors address this by employing higher order edge finite element discretisations based on unstructured meshes of tetrahedral elements with the addition of thin layers of prismatic elements. Furthermore, computer aided design (CAD) geometrical models of the non-threat and threat object are often not available and, instead, the authors extract the geometrical features of an object from an imaging procedure.

The authors obtain accurate numerical MPT characterisations that are in close agreement with experimental measurements for realistic physical objects. The assessment of uncertainty shows the impact of geometrical and material parameter uncertainties on the computational results.

The authors present novel computations and measurements of MPT characterisations of realistic objects made of magnetic materials. A novel assessment of uncertainty in the numerical predictions of MPT characterisations for uncertain geometry and material parameters is included.

Wireless sensor networks (WSN), as a solution for buried water pipe monitoring, face a new set of challenges compared to traditional application for above-ground infrastructure monitoring. One of the main challenges for underground WSN deployment is the limited range (less than 3 m) at which reliable wireless underground communication can be achieved using radio signal propagation through the soil. To overcome this challenge, the purpose of this paper is to investigate a new approach for wireless underground communication using acoustic signal propagation along a buried water pipe.

An acoustic communication system was developed based on the requirements of low cost (tens of pounds at most), low power supply capacity (in the order of 1 W-h) and miniature (centimetre scale) size for a wireless communication node. The developed system was further tested along a buried steel pipe in poorly graded SAND and a buried medium density polyethylene (MDPE) pipe in well graded SAND.

With predicted acoustic attenuation of 1.3 dB/m and 2.1 dB/m along the buried steel and MDPE pipes, respectively, reliable acoustic communication is possible up to 17 m for the buried steel pipe and 11 m for the buried MDPE pipe.

Although an important first step, more research is needed to validate the acoustic communication system along a wider water distribution pipe network.

This paper shows the possibility of achieving reliable wireless underground communication along a buried water pipe (especially non-metallic material ones) using low-frequency acoustic propagation along the pipe wall.

The purpose of this study is, to compare laser-based additive manufacturing and subtractive methods. Laser-based manufacturing is a widely used, noncontact, advanced manufacturing technique, which can be applied to a very wide range of materials, with particular emphasis on metals. In this paper, the governing principles of both laser-based subtractive of metals (LB-SM) and laser-based powder bed fusion (LB-PBF) of metallic materials are discussed and evaluated in terms of performance and capabilities. Using the principles of both laser-based methods, some new potential hybrid additive manufacturing options are discussed.

Production characteristics, such as surface quality, dimensional accuracy, material range, mechanical properties and applications, are reviewed and discussed. The process parameters for both LB-PBF and LB-SM were identified, and different factors that caused defects in both processes are explored. Advantages, disadvantages and limitations are explained and analyzed to shed light on the process selection for both additive and subtractive processes.

The performance of subtractive and additive processes is highly related to the material properties, such as diffusivity, reflectivity, thermal conductivity as well as laser parameters. LB-PBF has more influential factors affecting the quality of produced parts and is a more complex process. Both LB-SM and LB-PBF are flexible manufacturing methods that can be applied to a wide range of materials; however, they both suffer from low energy efficiency and production rate. These may be useful when producing highly innovative parts detailed, hollow products, such as medical implants.

This paper reviews the literature for both LB-PBF and LB-SM; nevertheless, the main contributions of this paper are twofold. To the best of the authors’ knowledge, this paper is one of the first to discuss the effect of the production process (both additive and subtractive) on the quality of the produced components. Also, some options for the hybrid capability of both LB-PBF and LB-SM are suggested to produce complex components with the desired macro- and microscale features.

Regardless of the materials used, additive manufacturing (AM) is one of the most popular emerging fabrication processes used for creating complex and intricate structural components. This study aims to investigate the effects of process parameters – namely, nozzle diameter, layer thickness and infill density on microstructure as well as the mechanical properties of 17–4 PH stainless steel specimens fabricated via material extrusion AM.

The experimental approach investigates the effects of printing parameters, including nozzle diameter, layer thickness and infill density, on surface roughness, physical and mechanical properties of the printed specimens. The tests were triplicated to ensure reproducibility of the experimental results.

The highest ultimate tensile strength, 795.26 MPa, was obtained on specimen that was fabricated with a 0.4 mm nozzle diameter, 0.14 mm layer thickness and 30% infill density. Furthermore, a 0.4 mm nozzle diameter also provided slightly better ductility. This came at the expense of surface finishing, as a 0.25 mm nozzle diameter exhibited better surface finishing over a 0.4 mm nozzle diameter. Infill density was shown to slightly influence the tensile properties, whereas layer thickness showed a significant effect on surface roughness. By contrast, hardness and ductility were independent of nozzle diameter, layer thickness and infill density.

This paper presents a comprehensive analysis relating to various input printing parameters on microstructural, physical and mechanical properties of additively manufactured 17–4 PH stainless steel to improve the printability and processability via AM.

Everyone is extremely concerned about environmental protection and health safety due to the rise in living standards. Plant-derived natural dyes have garnered much industrial attention in food, pharmaceutical, textile, cosmetics, etc. owing to their health and environmental benefits. The present study aims to focus on the elimination of the use of synthetic dyes and provides brief information about natural dyes, their sources, extraction procedures with characterization and various advantages and disadvantages.

In producing natural colors, extraction and purification are essential steps. Various conventional methods used till date have a low yield, as these consume a lot of solvent volume, time, labor and energy or may destroy the coloring behavior of the actual molecules. The establishment of proper characterization and certification protocols for natural dyes would improve the yielding of natural dyes and benefit both producers and users.

However, scientists have found modern extraction methods to obtain maximum color yield. They are also modifying the fabric surface to appraise its uptake behavior of color. Various extraction techniques such as solvent, aqueous, enzymatic and fermentation and extraction with microwave or ultrasonic energy, supercritical fluid extraction and alkaline or acid extraction are currently available for these natural dyes and are summarized in the present review article.

If natural dye availability can be increased by the different extraction measures and the cost of purified dyes can be brought down with a proper certification mechanism, there is a wide scope for the adoption of these dyes by small-scale dyeing units.

Air pollution is the combination of fine particles and gases in the atmosphere that harm humans and animals. Our objective is to find the various air pollution contaminants and its repercussion on Homo sapiens’ health. We discuss how air quality is measured with the air quality index and measures that help us cope with the consequences of air pollution. To carry out this study, we carried out a systematic literature review to uncover the different dimensions of air pollution and mitigation strategies. From the existing literature and observations of the different data sets, we can conclude that air pollutants have a severe impact on the life of Homo sapiens, causing various diseases such as respiratory issues, skin diseases, etc. Today, we have ample laws, but the need of the hour is to initiate new policies to change the behavioural of Homo sapiens. Our findings will help in decision-making by stakeholders such as policy-makers, manufacturing industries, households, etc. This article will also help in highlighting the need for Homo sapiens behavioural change.