Search results

The purpose of this paper is to demonstrate the processability of cohesive PE-HD particles in laser beam melting processes (LBM) of polymers. Furthermore, we present a characterization method for polymer particles, which can predict the quality of the powder deposition via LBM processes.

This study focuses on the application of dry particle coating processes to increase flowability and bulk density of PE-HD particles. Both has been measured and afterwards validated via powder deposition of PE-HD particles in a LBM machine.

For efficient coating in a dry particle coating process, the PE-HD particles and the attached nanoparticles need to show similar surface chemistry, i.e. both need to behave either hydrophobic or hydrophilic. It is demonstrated that dry particle coating is appropriate to enhance flowability and bulk density of PE-HD particles and hence considerably improves LBM processes and the resulting product quality.

At present, in LBM processes mainly polyamide (PA), 12 particles are used, which are so far quite expensive in comparison to, for example, PE-HD particles. This work provides a unique and versatile method for nanoparticulate surface modification which may be applied to a wide variety of materials. After the coating, the particles are applicable for the LBM process. Our results provide a correlation between flowability and bulk density and the resulting product quality.

The purpose of this paper is to investigate the influence of sprue distributions on the flow field and temperature field of the cladding casting process and verify the simulation results by experiments.

A steady-state mathematic model for the coupling of fluid flow, heat transfer and solidification to describe the process of cladding casting was present. The effect of sprue distributions on melt flow and temperature field was discussed. Based on the numerical simulation results, the cladding billet was prepared successfully. Moreover, the model has been verified against by temperature measurements during the cladding casting process.

There is a good agreement between the measured and calculated results. The homogeneity of melt flow determines the formability of cladding billets and circular temperature difference affects the bonding of the two alloys. The AA4045/AA3003 cladding billet with no defects in size of f140/f110 mm was fabricated successfully. The alloy elements diffused across the interface and formed diffusion layer with a thickness of 15 µm. The interface bonding strength is higher than the tensile strength of AA3003, indicating the metallurgical bonding between two alloys.

The casting parameters are limited to the aluminum alloy cladding billet in size of f140/f110 mm in this paper.

There are few reports of cladding billet, which are used to prepare condense pipes of automotive engines. The effect of distribution schemes on the cladding casting process is rarely studied.

This paper aims to focus on the development of the three-dimensional (3D) printing filaments based on acrylonitrile butadiene styrene (ABS) copolymer and styrene-ethylene/butylene-styrene (SEBS) block copolymer, with tailored viscoelastic properties and controlled flow during the 3D printing process.

In this investigation, ABS was blended with various amounts of SEBS via a melt mixing process. Then the ABS/SEBS filaments were prepared by a single-screw extruder and printed by the FDM method. The rheological properties were determined using an MCR 501 from Anton-Paar. The melt flow behavior of ABS/SEBS filaments was determined. The morphology of the filaments was studied by scanning electron microscope and the mechanical (tensile and impact) properties, surface roughness and void content of printed samples were investigated.

The rheological results can accurately interpret what drives the morphology and mechanical properties’ changes in the blends. The impact strength, toughness, elongation-at-break and anisotropy in mechanical properties of ABS samples were improved concurrently by adding 40 Wt.% of SEBS. The optimal tensile properties of blend containing 40 Wt.% SEBS samples were obtained at −45°/+45° raster angle, 0.05 mm layer thickness and XYZ build orientation. Optimized samples showed an 890% increase in elongation compared to neat ABS. Also, the impact strength of ABS samples showed a 60% improvement by adding 40 Wt.% SEBS.

The paper simultaneously evaluates the effects of material composition and 3D printing parameters (layer thickness, raster angle and build orientation) on the rheology, morphology, mechanical properties and surface roughness. Also, a mechanical properties comparison between printed samples and their compression-molded counterpart was conducted.

The relationship between the major process variables (laser power, laser scan speed, scan length, beam overlap and Q‐switch pulse frequency) of direct metal laser re‐melting and their effect on the structure of single‐ and multi‐layer copper coupons has been investigated. The work successfully produced selectively fused copper powder layers and simple three‐dimensional copper structures with suitable laser parameters being identified for the production of parts, including thin‐walled cubic structures. It was shown that the specific energy density needed to melt thick powder beds was less than that to melt multi‐layer builds and that the type of substrate material used significantly affected the process parameters. Thus, the substrate and its thermal properties have a significant effect on the melt pool size and freezing rate.

Additive manufacturing (AM) is revolutionizing the manufacturing industry due to several advantages and capabilities, including use of rapid prototyping, fabrication of complex geometries, reduction of product development cycles and minimization of material waste. As metal AM becomes increasingly popular for aerospace and defense original equipment manufacturers (OEMs), a major barrier that remains is rapid qualification of components. Several potential defects (such as porosity, residual stress and microstructural inhomogeneity) occur during layer-by-layer processing. Current methods to qualify AM parts heavily rely on experimental testing, which is economically inefficient and technically insufficient to comprehensively evaluate components. Approaches for high fidelity qualification of AM parts are necessary.

This review summarizes the existing powder-based fusion computational models and their feasibility in AM processes through discrete aspects, including process and microstructure modeling.

Current progresses and challenges in high fidelity modeling of AM processes are presented.

Potential opportunities are discussed toward high-level assurance of AM component quality through a comprehensive computational tool.

This study aims to obtain the mechanistic insights for the fabrication of pure copper thin wall components by selective infrared (IR) laser melting (SLM) and correlated with microstructure development, microhardness, surface morphology and phase analysis. Experimental processes for single track and selection of substrate materials have been studied using a combination of different laser powers and scanning speeds.

SLM of pure copper was performed on a YONGNIAN Laser YLMS-120 SLM machine using an Nd: YAG fiber laser operating at 1,060 nm in the NIR region. Single-track experiments and processing parameters are investigated through different combinations of laser power and scanning speed. The microstructure of the fabricated pure copper samples by SLM technique was analyzed by means of X-ray diffraction, scanning electron microscope equipped with energy disperse spectrometer, optical microscope (OM) and micro-hardness tester.

Steel-based substrates were found suitable for pure copper manufacturing due to sufficient heat accumulation. The width of a single track was determined by liner energy density, showing discontinuities and irregular morphologies at low laser powers and high scanning speeds. As a result of instability of the molten pool induced by Marangoni convection, cracks and cavities were observed to appear along grain boundaries in the microstructure. The top surface morphology of SLM-processed component showed a streamflow structure and irregular shapes. However, the powder particles attached to side surface, which manifest copper powders, are even more sensitive to melt pool of contour track. The crystal phase characteristics of copper components indicated increasing crystallite size of a-Cu, and the decreasing intensity of diffraction peak was attributed to the presence of defects during SLM. The maximum relative density and microhardness were 82 per cent and 61.48 HV0.2, respectively. The minimum thickness of a pure copper thin wall component was 0.2 mm.

This paper demonstrated the forming mechanism and explored feasibility of pure copper thin wall parts by SLM technology in the NIR region. The surface morphology, microstructure and crystal structure were preliminary studied with laser processing parameters.

Human aging is becoming a common issue these days as it results in orthopaedic-related issues such as joints disorderness, bone-fracture. People with age = 60 years suffer more from these aforesaid issues. It is expected that these issues in human beings will ultimately reach 2.1 billion by 2050 worldwide. Furthermore, the increase in traffic accidents in young people throughout the world has significantly emerged the need for artificial implants. Their implantation can act as a substitute for fractured bones or disordered joints. Therefore, this study aims to focus on electron beam melted titanium (Ti)-based orthopaedic implants along with their recent trends in the field.

The main contents of this work include the basic theme and background of the metal-based additive manufacturing, different implant materials specifically Ti alloys and their classification based on crystallographic transus temperature (including α, metastable β, β and α + β phases), details of electron beam melting (EBM) concerning its process physics, various control variables and performance characteristics of EBMed Ti alloys in orthopaedic and orthodontic implants, applications of EBMed Ti alloys in various load-bearing implants, different challenges associated with the EBMed Ti-based implants along with their possible solutions. Recent trends and shortfalls have also been described at the end.

EBM is getting significant attention in medical implants because of its minor issues as compared to conventional fabrication practices such as Ti casting and possesses a significant research potential to fabricate various medical implants. The elastic modulus and strength of EBMed ß Ti-alloys such as 24Nb-4Zr-8Sn and Ti-33Nb-4Sn are superior compared to conventional Ti for orthopaedic implants. Beta Ti alloys processed by EBM have near bone elastic modulus (approximately 35–50 GPa) along with improved tribo-mechanical performance involving mechanical strength, wear and corrosion resistance, along with biocompatibility for implants.

Advances in EBM have opened the gateway Ti alloys in the biomedical field explicitly ß-alloys because of their unique biocompatibility, bioactivity along with improved tribo-mechanical performance. Less significant work is available on the EBM of Ti alloys in orthopaedic and orthodontic implants. This study is directed solely on the EBM of medical Ti alloys in medical sectors to explore their different aspects for future research opportunities.

This study aims to comprehensively investigate the process-structure-property correlation of acrylonitrile butadiene styrene (ABS) parts manufactured by the overheat material extrusion (Mex) method. This study considers the relationships between the tensile and impact strength with temperature profiles, mesostructures and fracture behaviors of the ABS-printed parts.

The overheat printing condition was generated by using the highest possible printing temperature of the Mex printer used in this study together with cooling fan turned off. Temperature profiles of the polymer rasters were measured to characterize the diffusion time of the deposited rasters. Thermogravimetric analysis, differential scanning calorimetry and melt flow index were performed to study the thermal properties of the ABS feedstock. The mesostructures of the printed ABS samples were characterized by using an optical microscope, while their fracture surface was investigated using a field emission scanning electron microscope. The authors performed the tensile and impact tests following ASTM D3039 and D256-10A, respectively.

The use of the overheat Mex printing could offer better raster diffusion with reduced cooling rate and prolonged diffusion time. Consequently, the overheat printed ABS parts possessed a porosity as low as 1.35% with an increase in the weld length formed between the adjacent rasters of up to 62.5%. More importantly, the overheat printed ABS parts exhibited an increase of up to 70%, 84% and 30% in tensile strain at break, tensile toughness and impact strength, respectively, compared to their normal printed counterparts.

This study provides a facile but effective approach to fabricate highly dense and strong polymeric parts printed by Mex method for end-use applications.

The purpose of this paper is to investigate the effect of different heating approaches during thermal rounding of polymer powders on powder bulk properties such as particle size, shape and flowability, as well as on the yield of process.

This study focuses on the rounding of commercial high-density polyethylene polymer particles in two different downer reactor designs using heated walls (indirect heating) and preheated carrier gas (direct heating). Powder bulk properties of the product obtained from both designs are characterized and compared.

Particle rounding with direct heating leads to a considerable increase in process yield and a reduction in powder agglomeration compared to the design with indirect heating. This subsequently leads to higher powder flowability. In terms of shape, indirect heating yields not only particles with higher sphericity but also entails substantial agglomeration of the rounded particles.

Shape modification via thermal rounding is the decisive step for the success of a top-down process chain for selective laser sintering powders with excellent flowability, starting with polymer particles from comminution. This report provides new information on the influence of the heating mode (direct/indirect) on the performance of the rounding process and particle properties.